1977 Chicago Loop derailment
 | |
| Date | February 4, 1977 |
|---|---|
| Time | 5:25 pm |
| Location | Chicago, Illinois |
| Country | United States |
| Rail line | The Loop |
| Operator | Ravenswood |
| Type of incident | Collision |
| Cause | Driver error |
| Statistics | |
| Trains | 2 |
| Deaths | 11 |
| Injuries | Greater than 180 |
The 1977 Chicago Loop derailment occurred on February 4, 1977, when a Chicago Transit Authority elevated train rear-ended another on the northeast corner of the Loop at Wabash Avenue and Lake Street during the evening rush hour. The collision forced the first four cars of the rear train off the elevated tracks, killing 11 people and injuring over 180 as the cars fell onto the street below.
Infrastructure layout
"The Loop" not only refers to Chicago's central business district, but also a rectangular pattern formed by the city's elevated trains. Some trains entering the Loop do a complete circuit around the entire rectangular "loop", and after turning around all four corners, leave on the same path they came from. Other routes enter the Loop, turning only two of the corners, and then leave on a different route. Further complicating this is the fact that some trains' routes follow a clockwise pattern around the Loop, but others go counter-clockwise.
The 1977 crash itself involved trains from two lines. One was Ravenswood Line (today known as the Brown Line) and Lake–Dan Ryan Line (today, parts of the Green Line and Red Line). However, a third train, from the Evanston Express (Purple Line), factored in as well.
Earlier in the day of the accident, a switching issue forced dispatchers to reroute the Evanston Express to run counter-clockwise around the Loop instead of its normal clockwise route. This put it on the tracks normally used by the Ravenswood and westbound Lake–Dan Ryan trains. Because of congestion caused by this abnormal track sharing, the Ravenswood train would be required to stop short, waiting for the rerouted Evanston Express to clear before proceeding. Additionally, this delay meant that the Ravenswood was still in place when the Lake–Dan Ryan train arrived on these tracks, and it too was required to stop and wait for the Ravenswood to clear the track before proceeding.
Collision
At about 5:25 p.m., a Ravenswood train was waiting on the tracks, just past the northeast turn, waiting for the Evanston Express to clear the State/Lake platform. However, the Lake–Dan Ryan train did not stop as it approached the Ravenswood train. The Lake-Dan Ryan train proceeded against both track and cab signals, and struck the back of the Ravenswood train. This impact was at a slow speed, as the train had only started off a few seconds earlier and was still halfway through pulling out of Randolph/Wabash. Passengers on the train reported the impact as nothing more than a slight bump.
However, after the impact, the operator - Stephan A. Martin - continued to apply traction power. This resulted in the rear cars continuing to push forwards, pinning the front of the train against the waiting Ravenswood on the right-angle turn of the track. With the front Lake-Dan Ryan train unable to move forward, the pressure from behind caused the coupling bar between the first two cars to bend and the coupled ends of those two cars to be pushed in the air. As motor power continued to be applied, the first three cars were pushed further upwards, until they jackknifed and fell off the tracks. The second and third cars fell all the way to the street below, while the first car fell onto a track support structure. The fourth car, pulled forward by the third, was derailed and dangled between the track edge and surface street. The last four cars remained on the track - and, in fact, still in Randolph/Wabash station.
Investigation and CTA response
Subsequent investigation revealed that Martin had been smoking marijuana and had four marijuana cigarettes in his shoulder bag. He also had a poor safety record and was responsible for an earlier derailment, and he had a tendency to talk to passengers while driving the train.[1] It is theorized that, having made the normal station stop before the curve, Martin had caused the restrictive cab signal caused by the train ahead to be overridden. Distracted, he then left the station at under 15 miles per hour, which was slow enough to not trigger the automatic control, and then after the initial collision, panic or inertia caused him to move the Cineston controller forward resulting in the derailment.
As a result of the accident, the CTA forbade motormen to proceed past a red signal "on sight" without first getting permission from the Control Center.
References
Coordinates: 41°53′08″N 87°37′34″W / 41.8855°N 87.6262°W
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| ||||||||||
