3,4-Epoxycyclohexylmethyl-3’,4’-epoxycyclohexane carboxylate

3,4-Epoxycyclohexylmethyl-3’,4’-epoxycyclohexane carboxylate
Names
Other names
7-Oxabicyclo[4.1.0]hept-3-ylmethyl-7-oxabicyclo[4.1.0]heptane-3-carboxylate
Identifiers
2386-87-0
Abbreviations ECC
Jmol interactive 3D Image
PubChem 16949
Properties
C14H20O4
Molar mass 252.31 g·mol−1
Appearance Colorless liquid[1]
Density 1.17 g·cm−3[1]
Melting point −37 °C (−35 °F; 236 K)[1]
Slightly soluble (13.85 g·l−1 (20 °C))[1]
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
Infobox references

3,4-Epoxycyclohexylmethyl-3’,4’-epoxycyclohexane carboxylate (ECC) is a cycloaliphatic epoxy resin which is used in many industrial applications. It reacts by cationic polymerization using thermolatent photoinitiators to form crosslinked insoluble thermosets. Formulations based on cycloaliphatic epoxy resins such as ECC are known to form by curing thermosets with high heat and chemical resistance and good adhesion.[2]

History

The homopolymerization of ECC is based on radiation curing, which proceeds via a photochemical formation of a super acid and subsequent cationic polymerization. This was the first time realized in the 1970s.[3]

Fabrication

ECC can be prepared via Tishchenko reaction and subsequent epoxidation with a peracid.[4]

Properties

ECC has a dynamic viscosity of 400 mPa·s at 25 °C.[2]

Reactivity

For homopolymerization of ECC 1.5 to 3 wt. % of an initiator are added. Above 3 wt% initiator no further acceleration was found, increasing proportions of initiators, however, increase the brittleness of the formed thermoset. After a photopolymerization usually still a thermal post-curing is necessary for a complete reaction.[5]

It is known that the reactivity of the monomer is lower than it could be, since the contained ester group can react with the reactive, polymerizing chain end and stabilize it. It therefore reacts significantly slower than other molecules without ester group.[2][6] ECC polymerizes also much slower than radical monomers. It is therefore the object of research to find cationic polymerizable monomers with higher polymerization rate but same performance.[2]

Crosslinking

Cationically crosslinked ECC is used in a variety of industrial applications, due to its low viscosity, excellent electrical properties and high reliability among others as an electrical insulator, as coating and adhesive or as printing ink.[7] Homopolymerized ECC, however, is extremely brittle, what is disadvantageous. This problem can be addressed by integration of elastomer particles in the epoxy matrix, such as rubber or silicone, by integration of inorganic fillers[8] or by plasticization due to polymerization in the presence of polyester polyols.[9] The latter are covalently integrated via the monomer-activated mechanism into the polymer network.[10]

References

  1. 1 2 3 4 Record of 3,4-Epoxycyclohexylmethyl-3',4'-epoxycyclohexancarboxylat in the GESTIS Substance Database of the IFA, accessed on 1 January 2015.
  2. 1 2 3 4 Sasaki, Hiroshi (February 2007). "Curing properties of cycloaliphatic epoxy derivatives". Progress in Organic Coatings 58 (2-3): 227–230. doi:10.1016/j.porgcoat.2006.09.030.
  3. ↑ Crivello, J. V.; Lam, J. H. W. (October 1978). "Dye-sensitized photoinitiated cationic polymerization". Journal of Polymer Science: Polymer Chemistry Edition 16 (10): 2441–2451. doi:10.1002/pol.1978.170161004.
  4. ↑ Dillman, Brian; Jessop, Julie L. P. (2013-05-01). "Chain transfer agents in cationic photopolymerization of a bis-cycloaliphatic epoxide monomer: Kinetic and physical property effects". Journal of Polymer Science Part A: Polymer Chemistry 51 (9): 2058–2067. doi:10.1002/pola.26595.
  5. ↑ Atsushi Udagawa, Yasuhiko Yamamoto, Yoshio Inoue, Riichirô Chûjô (January 1991). "Dynamic mechanical properties of cycloaliphatic epoxy resins cured by ultra-violet- and heat-initiated cationic polymerizations". Polymer 32 (15): 2779–2784. doi:10.1016/0032-3861(91)90108-U.
  6. ↑ Crivello, James V.; Varlemann, Ulrike (October 1995). "Mechanistic study of the reactivity of 3,4-epoxycyclohexylmethyl 3′,4′-epoxycyclohexancarboxylate in photoinitiated cationic polymerizations". Journal of Polymer Science Part A: Polymer Chemistry 33 (14): 2473–2486. doi:10.1002/pola.1995.080331421.
  7. ↑ Cristina Mas, Ana Mantecón, Angels Serra, Xavier Ramis und Josep Maria Salla (2005-06-01). "Improved thermosets obtained from cycloaliphatic epoxy resins and γ-butyrolactone with lanthanide triflates as initiators. I. Study of curing by differential scanning calorimetry and Fourier transform infrared". Journal of Polymer Science Part A: Polymer Chemistry 43 (11): 2337–2347. doi:10.1002/pola.20711.
  8. ↑ Lützen, Hendrik; Bitomsky, Peter; Rezwan, Kurosch; Hartwig, Andreas (January 2013). "Partially crystalline polyols lead to morphology changes and improved mechanical properties of cationically polymerized epoxy resins". European Polymer Journal 49 (1): 167–176. doi:10.1016/j.eurpolymj.2012.10.015.
  9. ↑ Spyrou, Emmanouil (November 2001). "Radiation initiated cationic polymerization with tailor-made polyesters". Progress in Organic Coatings 43 (1-3): 25–31. doi:10.1016/S0300-9440(01)00240-5.
  10. ↑ Yagci, Yusuf; Schnabel, Wolfram (1999-09-01). "On the mechanism of photoinitiated cationic polymerization in the presence of polyols". Die Angewandte Makromolekulare Chemie 270 (1): 38–41. doi:10.1002/(SICI)1522-9505(19990901)270:1<38::AID-APMC38>3.0.CO;2-S.

Literature

This article is issued from Wikipedia - version of the Monday, January 25, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.