ALCO RSD-7

ALCO RSD-7

Type and origin Power type Diesel-electric Builder ALCO Model RSD-7 Total produced 29

Specifications AAR wheel arr C-C UIC class Co′Co′ Gauge 4 ft 8 ^1⁄2 in (1,435 mm) Prime mover ALCO 244 Cylinders V16

Performance figures Power output DL-600: 2,250 hp (1,678 kW; 2,281 PS) DL-600A: 2,400 hp (1,790 kW; 2,433 PS)

The ALCO RSD-7 was a diesel-electric locomotive of the road switcher type built by ALCO at Schenectady, New York between January 1954 and April 1956. Two versions were built, with the same RSD-7 model designation but different specifications and power ratings, although both used the ALCO 244 engine in V16 configuration. Specification DL-600, of which only two were built, developed 2,250 hp (1,678 kW; 2,281 PS) and used the 244G engine. The revised specification DL-600A, numbering 27 locomotives, was rated at 2,400 hp (1,790 kW; 2,433 PS) and used the 244H engine. The RSD-7 was superseded by the ALCO 251-engined ALCO RSD-15, which looks very similar.^[1] The RSD-7 was the last ALCO diesel built with a 244 engine.

Both rode on a pair of three-axle trucks with all three axles on each truck powered; this is a C-C wheel arrangement. These trucks have an unequal axle spacing due to traction motor positioning; the outer two axles on each truck are closer together than the inner two. The RSD-7 used the GE 752 traction motor. The six-motor design allowed better tractive effort at lower speeds.

Demonstrators

The two RSD-7 demonstrators were significant for Alco. They were built with the intention of challenging the Fairbanks-Morse Train Master H24-66. When built in early 1954 the RSD-7 delivered the highest continuous tractive effort of all diesel locomotives then available. The RSD-7 offered 75% more dynamic braking capacity than any standard freight unit available at the time. The superlatives of the RSD-7 allowed two units to do the work of three conventional 4-motor units. The dynamic brake system was mounted on top the long hood, leaving room in the short hood for a steam generator. The RSD-7 was the first Alco built with the notched corner sand fills. The RSD-7 was the first Alco to use the coiled air brake intercoolers mounted just above and ahead of the radiator intakes. The RSD-7 was the first Alco to use the then new Model 710 water cooled turbocharger in a 16-cylinder engine. The two demonstrators were numbered DL600 and DL601. The DL600 weighed 360,000 pounds at the standard 60,000 pounds per axle. The DL601 weighed 390,000 to test the gains in adhesion from the extra weight. Additional experimentation by Alco used new fuel injection pumps and nozzles, increased fuel rack settings, and an aftercooler was applied to reduce engine air inlet temperature. The aftercooler allowed higher density inlet air into the engine that promoted greater fuel burning efficiency. The aftercooler became the feature that allowed the 244 to be pushed to 2400 horsepower and the designation of 244H. The 244H is also known as the Alco 250 engine to disassociate it from the troubled 244 engine series. The maroon, yellow and gray painted RSD-7 demonstrators began a 23-railroad, 50,000 mile demonstration tour in the Spring of 1954. The tour concluded in September 1954 and the two units were refurbished before sale to the Santa Fe.

References

1. Pinkepank, Jerry A. (1973). The Second Diesel Spotter’s Guide. Milwaukee, WI: Kalmbach Publishing Company. ISBN 0-89024-026-4.

• The American Locomotive Company A Centennial Remembrance by Richard Steinbrenner pp. 346–348.

External links

• RSD-7 Roster