Safe area (television)

Not to be confused with Broadcast-safe.
Safe areas on a PAL screen.
Red: Invisible area
Yellow: Action-safe area
Green: Title-safe area

Safe area is a term used in television production to describe the areas of the television picture that can be seen on television screens.

Older televisions can display less of the space outside of the safe area than ones made more recently. Flat panel screens, Plasma displays and liquid crystal display (LCD) screens generally can show most of the picture outside the safe areas.

The use of safe areas in television production ensures that the most important parts of the picture are seen by the majority of viewers.

The size of the title-safe area is typically specified in pixels or percent. The NTSC and PAL analog television standards do not specify official overscan amounts, and producers of television programming use their own guidelines.

Title-safe area

A simulation of how the end credits of a TV show might have looked on an old TV set if the editor neglected to make sure they fell within the boundaries of the title-safe area.

The title-safe area or graphics-safe area[1] is, in television broadcasting, a rectangular area which is far enough in from the four edges, such that text or graphics show neatly: with a margin and without distortion. This is applied against a worst case of on-screen location and display type. Typically corners would require more space from the edges, but due to increased quality of the average display this is no longer the concern it used to be, even on CRTs.

If the editor of the content does not take care to ensure that all titles are inside the title-safe area, some titles in the content could have their edges chopped off when viewed in some screens.[2][3]

Video editing programs that can output video for either television or the Web can take the title-safe area into account. In Apple's consumer-grade NLE software iMovie, the user is advised to uncheck the QT Margins checkbox for content meant for television, and to check it for content meant only for QuickTime on a computer.[4] Final Cut Pro can show two overlay rectangles in both its Viewer and Canvas; the inner rectangle is the title-safe area and the outer rectangle is the action-safe area.[5]

In the illustration, the green area is referred to as the "title-safe" area (note that these colors are for illustration only and do not appear on the television screens). This area will be seen by all television screens, no matter when they were made, unless the user has modified the settings. The term "title-safe" originated from the fact this is where it is safe to display text such as lower thirds or full-screen graphics listing information such as telephone numbers.

Action-safe area

Depending on how a television set is adjusted, viewers can see a larger area than the title-safe area. The action-safe area is a larger rectangle, consisting of the green title-safe area and a rectangle around it shown in yellow. As of 2007, most television stations and networks will place information within this area. This area can be considered the "margin" of the television screen in that picture elements are generally kept out of this area to create a buffer around the edge of the screen so elements don't pile up against the edge of the screen. If the station uses a permanent digital on-screen graphic, it is placed just near the corner of the yellow area.

However, the yellow area might be used if the television station wants the information to block against the edge of the screen. For example, many stations place tickers that run horizontally in some of the yellow area.

Action-safe area is applied against a worst case of on-screen location and display type.

Overscan

Main article: Overscan

The red border in the illustration represents the overscan, the area of the active picture outside the action-safe area. It is not shown on most consumer television screens, unless the user modifies the television's settings. It is generally considered safe to have elements that shouldn't be seen by the viewers placed in this area, such as the edge of the set or cables and other equipment. However, some television production personnel don't place anything in this area they don't want viewers to see because the red area is always transmitted and could potentially be seen by a viewer with the correct equipment. Television stations generally have professional-grade monitors that can be put into "underscan" mode. These monitors often include white lines showing where the title-safe and safe areas are located. In addition, TV tuner cards and DVD players for personal computers often show the entire picture.

The action-safe area (green + yellow) and overscan area (red) make up the entire transmitted image, or active picture.

In addition to active picture, analog broadcast signals contain blanking areas that provide timings and control. When applying digital compression such as MPEG-4, it is only sensible to compress picture that actually exists, and active picture is what is used — including areas not available in action-safe areas. (MPEG-2 is a bad example, since it has many ties to analogue broadcasting, and employs only a few set sizes; this is why it will always capture nominal analogue blanking in addition to the active picture next to it.)

Since there are such a wide variety of television screens that may display pictures slightly differently, programs produced in 4:3 aspect ratio are transmitted with picture information in the yellow and red areas to ensure the picture takes up the entire screen with no black area around the edges. Widescreen programs in 14:9 or 16:9 aspect ratio, on the other hand, are produced with zero overscan at the top and bottom of the picture, where the letterbox bars appear on a 4:3 television.

Editing

Some video editing software packages for non-linear editing systems (NLE) solutions have a setting which shows the safe areas while editing.

Adobe After Effects

Adobe After Effects can show safe areas overlay in composition view.

Adobe Premiere Pro

Adobe Premiere Pro asks user to specify safe areas during project creation.

Sony Vegas Pro

In Sony Vegas Pro, this setting is found just above the preview in Overlays >> Safe Areas.

Thomson Grass Valley - Edius

In Edius, the "action-safe" and "title-safe" area is set and selected in the application settings menu.

Final Cut Pro

In Final Cut Pro, users can enable both title- and action-safe overlays in the canvas and/or viewer by selecting the appropriate window and going to View -> Show Title-Safe.

Avid Media Composer

In Avid Media Composer, users can enable both title and action-safe overlays in the Source/Record monitors by selecting the appropriate monitor and turning on the grid in the fast menu. Grid settings can be adjusted from the Project Window. A range of presets are available for film and television formats.

See also

References

  1. ↑ EBU Recommendation R95: Safe areas for 16:9 television production. September 2008. Accessed 2013-03-18.
  2. ↑ David Pogue, iMovie HD & iDVD 5: The Missing Manual. Sebastopol, California: Pogue Press/O'Reilly (2005): 355
  3. ↑ Jon Bounds, John Buechler, & Jen DeHaan, Windows Movie Maker 2: Zero to Hero. New York: Friends of ED (2003): 209. "Try to keep your words inside the title-safe area—a few inches in from all edges of the screen. Graphics placed outside the safe area may not display properly on a television screen."
  4. ↑ David Pogue, iMovie HD & iDVD 5: The Missing Manual. Sebastopol, California: Pogue Press/O'Reilly (2005): 186.
  5. ↑ Lisa Brenneis, Final Cut Pro 3 for Macintosh. Berkeley, California: Peachpit Press (2002): 596.
This article is issued from Wikipedia - version of the Wednesday, January 06, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.