Aerodynamic levitation

Aerodynamic levitation apparatus: a spherical sample is floated on a gas stream which flows through the conical nozzle. Sample is heated by a CO2 laser and temperature is measured from sample brightness by a pyrometer.
Aerodynamic levitation of objects can be also a nice effect in party locations. Here a light ball flies in an air stream generated by a ventilator in the square box

Aerodynamic levitation is the use of gas pressure to levitate materials so that they are no longer in physical contact with any container. In scientific experiments this removes contamination and nucleation issues associated with physical contact with a container.

Overview

The term aerodynamic levitation could be applied to many objects that use gas pressure to counter the force of gravity, and allow stable levitation. Helicopters and air hockey pucks are two good examples of objects that are aerodynamically levitated. However, more recently this term has also been associated with a scientific technique which uses a cone-shaped nozzle allowing stable levitation of 1-3mm diameter spherical samples without the need for active control mechanisms.[1]

Aerodynamic levitation as a scientific tool

These systems allow spherical samples to be levitated by passing gas up through a diverging conical nozzle. Combining this with >200W continuous CO2 laser heating allows sample temperatures in excess of 3000 degrees Celsius to be achieved.

When heating materials to these extremely high temperatures levitation in general provides two key advantages over traditional furnaces. First, contamination that would otherwise occur from a solid container is eliminated. Second, the sample can be undercooled, i.e. cooled below its normal freezing temperature without actually freezing.

Undercooling of liquid samples

Undercooling, or supercooling, is the cooling of a liquid below its equilibrium freezing temperature while it remains a liquid. This can occur wherever crystal nucleation is suppressed. In levitated samples, heterogeneous nucleation is suppressed due to lack of contact with a solid surface. Levitation techniques typically allow samples to be cooled several hundred degrees Celsius below their equilibrium freezing temperatures.

Glass produced by aerodynamic levitation

Since crystal nucleation is suppressed by levitation, and since it is not limited by sample conductivity (unlike electromagnetic levitation), aerodynamic levitation can be used to make glassy materials, from high temperature melts that cannot be made by standard methods. Several silica-free, aluminium oxide based glasses have been made.[2][3][4]

Physical property measurements

In the last few years a range of in situ measurement techniques have also been developed. The following measurements can be made with varying precision:

electrical conductivity, viscosity, density, surface tension, specific heat capacity,

In situ aerodynamic levitation has also been combined with:

X-ray synchrotron radiation, neutron scattering, NMR spectroscopy

See also

Further reading

References

  1. Paul C. Nordine; J. K. Richard Weber & Johan G. Abadie (2000), "Properties of high-temperature melts using levitation", Pure and Applied Chemistry 72 (11): 2127–2136, doi:10.1351/pac200072112127
  2. J. K. Richard Weber; Jean A. Tangeman; Thomas S. Key; Kirsten J. Hiera; Paul-Francois Paradis; Takehiko Ishikawa; et al. (2002), "Novel Synthesis of Calcium Oxide–Aluminum Oxide Glasses", Japanese Journal of Applied Physics 41: 3029–3030, Bibcode:2002JaJAP..41.3029W, doi:10.1143/JJAP.41.3029
  3. J. K. Richard Weber; Johan G. Abadie; April D. Hixson; Paul C. Nordine; Gregory A. Jerman (2004), "Glass Formation and Polyamorphism in Rare-Earth Oxide–Aluminum Oxide Compositions", Journal of the American Ceramic Society 83 (8): 1868–1872, doi:10.1111/j.1151-2916.2000.tb01483.x
  4. L. B. Skinner; A. C. Barnes & W. Crichton (2006), "Novel behaviour and structure of new glasses of the type Ba–Al–O and Ba–Al–Ti–O produced by aerodynamic levitation and laser heating", Journal of Physics: Condensed Matter 18 (32): L407–L414, Bibcode:2006JPCM...18L.407S, doi:10.1088/0953-8984/18/32/L01
This article is issued from Wikipedia - version of the Saturday, January 02, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.