Altec Lansing Duplex

Duplex was the trade name name given by Altec Lansing to its line of coaxial loudspeakers, beginning with the first model 601 in 1943. However, the name was most commonly associated with the subsequent model 604 which was a seminal loudspeaker that became a milestone in loudspeaker development. Well over a dozen different models carried the Duplex name over a near 50-year period. The vast majority consisted of a high frequency (HF) compression driver mounted to the back of a large diameter (12"-15") paper cone low frequency (LF) driver. However, there were also a few models with small diameter LF cones and direct radiator tweeters.

The Duplex speakers were extremely versatile with the 604 model alone finding application in studio monitoring, home high fidelity, public address, tour sound reinforcement, cinema sound and installed sound. A number of duplex drivers were developed for very specialized applications, such as ceiling speakers. Some of the more significant models in the Duplex lineup were, in order of introduction, the 15" 601, 15" 604, 15" 602, 12" 601, 15" 605, 15" 904 and 12" 920.

The significance of the Duplex loudspeakers is evidenced by the fact that the Altec Lansing 604 Duplex was inducted into the TECnology Hall of Fame in 2005.[1]

Altec 601

The path to the Duplex line started with Altec's acquisition of the Lansing Manufacturing Company (LMCO) in 1941. That acquisition brought Altec into the loudspeaker manufacturing business and brought the loudspeaker design services of its principal, Jim Lansing. Shortly after that, Altec was approached by one of its dealers, named Jim Crawford, with a request to develop a compact loudspeaker. He was seeing demand for a quality loudspeaker small enough to be used in radio stations for monitoring. The current two way speakers with separate LF and HF drivers were too large for this application and Art suggested a coaxial design whereby a LF and HF driver could be combined in one unit. Altec saw the merit of this concept and began development under Jim Lansing and John Hilliard.

By 1943, a prototype was rapidly developed with off-the-shelf LMCO components. The LF portion of the driver was developed by taking the field coil motor from the LMCO 287 compression driver and using it to drive the cone from one of LMCO's 15" LF drivers with a 2" voice coil. Both were mounted on a stamped steel frame. An LMCO 801 field coil compression driver with a 1.75" diaphragm was used as is for HF reproduction and mounted coaxially to the back of the 287 motor. A horn throat from the 801 penetrated the center of the LF field coil and exited into a small multicellular horn mounted in front of the LF cone. The horn was designed with a cut-off frequency of 900 Hz and the system was set with a crossover frequency of 1200 Hz.

The prototype confirmed the concept and went into production in 1943 as the model 601 Duplex, but it was not long lived. In less than a year, a significant redesign was underway to substantially improve the driver. The primary motivation was to replace the field coil motors with permanent magnet motors. Field coils are very powerful allowing for very efficient loudspeakers. However, they require an external power supply which greatly limits their areas of application.

When the 601 was first designed, there were no commercially available permanent magnets that could cost effectively provide the same level of magnetic energy as a field coil. During WWII, Altec was involved in developing submarine detection equipment for the Marine Airborne Detection program. It was through this that they were introduced to a new type of permanent magnetic material; Alnico V. This was much stronger than any other permanent magnet at the time. In 1944, they used this technology to create a permanent magnet version of the 601 the which became the famous 604.

There has been much confusion about the original 601 due to the fact that very few were made, with almost no survivors, and because the model name was re-used in the 1950s for a completely different Altec Lansing Duplex driver. The 1950s version of the 601 was a 12" diameter coaxial speaker with a miniature HF compression driver mounted within the motor of the LF driver using permanent magnets. This confusion was exacerbated in 1988 when Altec Lansing misidentified the later 12" 601 as the original 601 in their own promotional literature celebrating their 50th anniversary. That mistake was carried forth for years in subsequent Altec Lansing literature. However, at least one original field coil 601 is known to exist (S/N 150) and has been confirmed as a 15" model.[2] In addition, copies of the original sales literature exist that accurately describe it.[3]

Altec 604

The permanent magnet upgrade of the 601 was released in 1944 as the 604, at which point the 601 was discontinued.[4] The 604 was the same basic design using a 15-inch LF driver, but with a larger 3" voice coil, individual Alnico V magnets for the LF and HF drivers, and a cast aluminum frame.

When making the horn for the 601/604, it had to be designed so the sound coming from it would not interfere with the sound from the bass driver. To overcome this, a 2x3 multicellular design with a dispersion of 40°×90° was used. This allowed the sound to leave the horn and be dispersed largely without coming into contact with the cone of the bass driver. The horn was also coated with a damping compound to reduce high frequency resonance from the plastic. The original 601 The first 604 had a crossover frequency of 2000 Hz.

Both the 601 and the first 604 had a frequency response of 60 Hz to 16 kHz with a power rating of only 25 watts, relatively low but acceptable due to the speakers' efficiency. As amplifiers of the time did not produce much power, the speakers had to be extremely efficient to produce adequate loudness. The next speaker in the 604 line to be released was the 604B, with a slightly higher power handling at 30 watts and a better frequency response ranging from 30 Hz to 16 kHz. Also, this speaker had a lower crossover frequency of 1000 Hz.

Following the 604B came the 604C. Again, the power handling capacity and frequency response were increased to 35 watts and 30 Hz to 22 kHz, respectively. Following the 604C was the 604-8G, released in 1973 and produced until 1979. The power handling capacity was substantially increased to 65 watts and the frequency response was improved, bringing the bass response down to 20 Hz and treble respones up to 22 kHz.

The next big step in the 604 family was the 604-8K, which was similar in most respects to the 604-8G, but used a ferrite magnet instead of an Alnico V magnet. Ferrite magnets are much more resistant to being demagnetized and are thus more robust. However, debate continues to this day as to the sonic superiority of Alnico V vs ferrite magnetic motors as it relates to freedom from distortion. Also, the 604-8K used a Mantaray horn design, rather than the multi-cell horn design of the older models, producing smoother high frequency dispersion.

The 604 achieved its greatest fame as a recording studio monitor. Its compact size, wide bandwidth, high output and point source topology made it an ideal choice for the needs of the new tape recording technology introduced in the late 40's and early 50's. Prior to tape recorders, commercial recordings were cut directly to a master disk, nominally in one take with no real provision for editing. As a result, monitoring needs were very rudimentary and mainly regarded monitoring for technical defects.

In contrast, the tape recorder ushered in editing, overdubbing and ultimately multi-track recording and stereo output. There was the continuing need to critically listen to recordings long after the performance was captured to accommodate the substantial post processing now required to develop a final master tape. At the time, the 604 was unequalled in this application, given the significant increase in accuracy it presented over the competition. As a result, it became ubiquitous in North American recording studios for the next two decades. In the 1970s it was overtaken by competition, primarily from JBL. However, later that same decade, it would have a resurgence that lasted well into the 1980s when UREI introduced their 813 studio monitor that incorporated a modified 604 driver with a time-aligned cross-over. For a time, the 813 was nearly as ubiquitous as the original 604.

Altec 904

Shortly after the introduction of the 604-8K, Altec released the 904-8A, which was basically a high powered 604-8K that could handle up to 150 watts. Both remained in production until the shutdown of Altec Lansing Professional by its then owners, Telex Communications, in 1998.

References

  1. ↑ "1944 Altec Lansing 604 Duplex Speaker". Mix. September 1, 2006. Retrieved June 26, 2013.
  2. ↑ "Altec 601 Duplex Surviving Example". Lansing Heritage. Retrieved 24 March 2016.
  3. ↑ "Altec 601 Duplex Specification". Lansing Heritage. Retrieved 24 March 2016.
  4. ↑ alteclansingunofficial.nlenet.net

External links

"

This article is issued from Wikipedia - version of the Friday, April 29, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.