Apple II serial cards
- This article is a sub-page of Apple II peripheral cards.
Apple II serial cards primarily used the serial RS-232 protocol. They most often were used for communicating with printers, Modems, and less often for computer to computer data transfer. They could be programmed to interface with any number of external devices which were RS-232 compatible. Most serial cards had speed ranges starting from 110 bit/s up to 19,200 bit/s, however some could be modified to go much faster. The most popular and widely used of these cards was Apple Computer's Super Serial Card, a solid design that was often copied for maximum software compatibility of the end product.
Apple II Communications Card – Apple Computer
The Apple II Communications Card is the original serial card from Apple Computer. Released in 1978 for $225, it was designed to work with modems utilizing acoustic couplers. It offered speeds of 110 and 300 bit/s but with a simple hardware modification (described in the manual accompanying the card) one could change this to 300 and 1200 bit/s, or 1200 and 4800 bit/s. [1]
Apple II Serial Interface Card – Apple Computer
The Apple II Serial Interface Card was released by Apple Computer shortly after the Communications Card, in August 1978. Designed for printing, this card had ROM revisions, P8 and P8A. The P8A ROM supported handshaking while the earlier P8 rom didn't. Unfortunately the P8A ROM revision was not compatible with some printers that worked under the original P8 ROM.[1]
Serial Pro – Applied Engineering
The Serial Pro serial interface card from Applied Engineering was Super Serial Card compatible, however it eliminated the need for the use of a jumper block if the user wanted to switch between Printer mode or Modem mode. The Serial Pro, being a multifunction card, included a ProDOS and DOS 3.3 compatible clock/calendar thus combining the capabilities of two cards into one, freeing up an extra slot for those with highly populated machines. This card was unique in the sense that it did not use "Phantom Slots" to achieve this functionality. Previous multifunction cards required that a secondary function be "mapped" to a different slot in the computer's memory, rendering that slot unusable. If used with a dot-matrix printer, the Serial Pro offered several screen-print variations. It could print either HiRes page (or both in a single dump) normally, or print page one rotated or inverted. The Serial Pro utilized the MOS Technology 6551 ACIA chip and offered serial baud rates from 50 bit/s to 19,200 bit/s. The lifespan of the clock battery was touted as 20 years. The card retailed for $139 during the late 1980s. [2]
For more on the Serial Pro's clock capabilities, see its entry in Apple II system clocks.
Super Serial Card – Apple Computer
Apple Computer's Super Serial Card, sometime abbreviated as "SSC", is the most well known of communication cards made for the Apple II. Apple called it "Super" because it was able to function as both of Apple's previous cards, the Apple II Communications Card for modem use and the Apple II Serial Interface Card for printer use. A jumper block was used to configure the card for each of the two modes. The card has a maximum speed of 19,200 bit/s and is compatible with both ROM revisions of the Apple II Serial Interface Card. Reliable communications at 9600 bit/s and higher required disabling of interrupts. The card can actually run at 115,200 bit/s as well, using undocumented register settings; but speeds between 19,200 and 115,200 are not possible using this technique. The Super Serial Card was released in 1981 and utilizes the MOS Technology 6551 serial communications chip.
Other Serial Cards
Use this article for: Apple II multi I/O cards
- Apricorn Serial Interface – Apricorn
- Super Serial Imager – Apricorn
- 7710 Serial Interface – California Computer Systems
- 7711 Super Serial Interface – California Computer Systems
- Serial Interface DK 244 – Digitek International Ltd
- SV-622 Serial Interface – Microtek
- SeriALL – Practical Peripherals
- Multicore – Quadram
- Super-COMM – Sequential Systems – SSC compatible, built in term program in ROM, supported grappler screen dumps and graphics [3]
- AIO Interface – SSM or Transend
- ASIO Interface – SSM or Transend
- Alphabits – Street Electronics
- Super Serial Board – MC Price Breakers – Generic Super Serial Card clone
References
- 1 2 Apple II History, Chapter 12 - Apple II Abroad & Peripherals
- ↑ Applied Engineering Spring/Summer '88 Catalog
- ↑ Sequential Systems website (via the Wayback Machine)
|