Audio analyzer

An Audio Analyzer is a test and measurement instrument used to objectively quantify the audio performance of electronic and electro-acoustical devices. Audio quality metrics cover a wide variety of parameters, including level, gain, noise, harmonic and intermodulation distortion, frequency response, relative phase of signals, interchannel crosstalk, and more. In addition, many manufacturers have requirements for behavior and connectivity of audio devices that require specific tests and confirmations.

Audio analysis requires that the device under test receive a stimulus signal of known characteristics, with which the output signal (response) may be compared by the analyzer in order to determine differences expressed in the specific measurements. This signal may be generated or controlled by the analyzer itself or may come from another source (e.g., a recording) as long as characteristics relative to the desired measurement are defined.

As test and measurement equipment, audio analyzers are required to provide performance well beyond that of the typical devices under test (DUTs). High quality audio analyzers must demonstrate vanishingly low levels of noise, distortion and interference in order to be deemed trustworthy by engineers and designers. For example, while a commercial CD player can achieve a total harmonic distortion plus noise (THD+N) ratio of approximately -98 dB at 1 kHz, a high quality audio analyzer may exhibit THD+N as low as -121 dB (typical performance of the Audio Precision APx555).

Audio Analyzers find use in both development and production of products. A design engineer will find it very useful when understanding and refining product performance, while a production engineer will wish to perform tests to rapidly confirm that units meet specifications. Very often audio analyzers are optimized for one of these two cases.

Current popular audio analyzer models include: APx585 and APx555 (Audio Precision), dScope Series III (Prism Sound), U8903A (Agilent) and the UPP and UPV analyzers (Rohde & Schwarz).

Audio Precision APx525, a current audio analyzer

HP8903B, an audio analyser of mid-1980s

History

One of the earliest reliable sources used for audio test was the first product made by Hewlett-Packard in 1939, the HP200A audio oscillator. The clever and inexpensive design of the HP200A allowed testers to generate very high quality, low distortion sine waves that could be used for testing. This was followed by the company's introduction of the HP320A and HP320B Distortion Analyzers in 1941.

These early analyzers could only determine total harmonic distortion and noise combined, and worked by employing a steep notch filter to remove the fundamental frequency of the stimulus signal from the output of the DUT. The remaining signal was measured as an AC voltage, and thus allowed for the manual calculation of total noise and distortion to approximately 0.1% minimum.

Subsequent products from HP, Wandell & Goltermann, Radford, Marconi, Sound Technology, and Amber continued to refine measurement capabilities from the 1950s through the 1970s, but the model of usage remained relatively constant; signal generators and analyzers were separate pieces of equipment, and testing involved careful tuning of each one by a person with high technical skills. This changed in 1980 with the introduction of the Tektronix AA501 Distortion Analyzer, which automated the processes of setting levels, frequency tuning and nulling. At this same time Hewlett-Packard introduced the popular HP8903B, which combined a high quality signal generator and analyzer in a single unit.

By the mid-eighties, Tektronix ceased production of audio test equipment, and in 1984 members of the team that had developed the AA501 started Audio Precision. The first Audio Precision product was the System One, which combined an integrated generator and analyzer with a connected PC to fully automate test procedures and provide a much higher degree of computational power than the simple microprocessors used in other products at the time. The novel use of a PC allowed for a high degree of custom automation and enabled a radically different visual presentation of results.

The combination of PC technology with audio analyzers was adopted by others, including Prism Sound (dScope), Rohde and Schwarz (UPL), and Stanford Research (SR1). As the power of available PCs increased, measurements themselves migrated from being performed internally by audio analyzers to applications running on connected PCs performing FFT (Fast Fourier Transform) calculations, greatly increasing the flexibility and resolution of many results.

In addition to analog, audio analyzers today are frequently capable of generating and measuring audio over several different types of digital I/O. For example, the Rohde and Schwarz UPP offers AES/EBU, S/PDIF, I²S and HDMI options; the Audio Precision APx500 Series analyzers support AES/EBU, S/PDIF, I²S, HDMI, PDM (Pulse Density Modulation), and Bluetooth radio, and are fully DSP based.

Block Diagram and Operation

A modern audio analyzer consists of:

An audio generator that provides stimulus, both analog and digital, to the DUT.
Audio input stages that receive a response from the DUT, both analog and digital, and convert it to appropriate signals (analog or digital) for analysis
An signal analyzer that filters the response and calculates results of measurements, commonly a connected or embedded PC in modern solutions
A form of output to the user (display, report, etc.)

In a closed-loop test, the analysis engine controls the audio generator while simultaneously measuring the output of the DUT, as shown below:

Block Diagram of closed-loop testing with an audio analyzer

The signal analyzer can provide control to both the audio generator and the audio input stages, assuring that test conditions are met. This also permits precise time relationships between the stimulus and response of a DUT to be determined.

Block Diagram of open-loop testing with an audio analyzer

In an open-loop test, the signal analyzer has no control over the audio source driving the DUT, and thus the user must take care to ensure that the source is providing a signal of appropriate characteristics. Open loop tests are useful for measuring DUTs that have no direct signal input, such as a CD or MP3 player.

Electro-acoustic Devices

Electro-acoustic devices such as loudspeakers and microphones present special problems for analysis, as they must receive or transmit signals through air. In these cases, the DUT in the model shown above must be replaced with the complete electro-mechanical system, e.g., a power amplifier to drive a loudspeaker, a loudspeaker, a measurement microphone and microphone pre-amplifier. The actual device under test can be measured only when the other devices in this system are fully characterized, so that the contributions from these devices may be subtracted from the response. Many modern audio analyzers contain measurement sequences that automate this procedure, and the focus of recent developments has been on quasi-anechoic measurements. These techniques allow loudspeakers to be characterised in a non-ideal (noisy) environment, without the need for an anechoic chamber, which makes them ideally suited for use in high volume production line manufacturing. Most quasi-anechoic measurements are based around an impulse response created from a sine wave whose frequency is swept on a logarithmic scale, with a window function applied to remove any acoustic reflections. The log swept sine method increases signal-to-noise ratio and also allows measurement of individual distortion harmonics up to the Nyquist frequency, something which previously impossible with older analysis techniques such as MLS (Maximum Length Sequence).

Audio Generator

An audio generator suitable for use in test and measurement must meet several criteria that apply to both analog and digital stimulus:

Ability to generate different waveform types
- Sine
- Square
- Multitone (a group of simultaneous sine waves)
- Sweep (move continuously from one specified frequency to another)
- Standard Inter-modulation waveforms (SMPTE, DIN, DFD, and DIM)
- Arbitrary waveforms
Extremely low residual distortion and noise
Sufficient range of amplitude
Sufficient range of frequency
Extremely high accuracy of amplitude
Extremely high accuracy of frequency
Adjustable and accurate source impedance
Balanced/unbalanced output options (analog)
AC and DC coupling

Additionally, the generator will allow for the definition of a precise frequency range and amplitude of the stimulus presented to the DUT. This is critical when aligning test conditions to the characteristics of the DUT.

Signal Analyzer

Prior to the introduction of integrated audio analyzers, audio generators and audio analyzers were separate pieces of equipment. In this article, signal analyzer refers to the element of a modern audio analyzer that implements the actual measurements.

Whether realized in analog circuits, digital signal processing (DSP) or FFT, the analyzer engine must provide high precision implementations of:

AC/DC voltmeter (peak and RMS)
High pass, low pass and weighting filters
Band pass and notch filters
Frequency counter

As most modern instruments are digitally based, signal analysis is frequently performed using FFT-based calculations, allowing many results to be calculated in a single test pass.

Results of these measurements are processed by the analyzer into readable data using a variety of standard units and formats, such as volts, dB, dBu, SPL, ohms, relative percentage, etc., depending upon the specific measurement being reported. Derived results are achieved by combining several primary results into a calculated result.

Measurements and Results

Audio analyzers are capable of measuring many types of parameters. The fundamental measurements are:

Level and gain: Level describes the magnitude of a signal, and may be expressed in absolute or relative terms. Common absolute units may be volts, watts, dBV and dBu, while relative measurements are expressed most commonly in dB. Level may also be conditioned as a peak measurement or an RMS measurement. Gain is the ratio of signal level at a DUT's output divided by the signal level at the input, usually expressed in dB.
Frequency response: measures the output level of a DUT as a function of frequency. Level is expressed in the same units as above, typically dBV and dBu.
Total Harmonic Distortion plus Noise (THD+N): Harmonic distortion products are multiples of stimulus frequencies, while noise is energy that is mathematically unrelated to the input signal. As a signal result, THD+N can be considered all signal content in the DUT response that is not contained in the stimulus.
Signal-to-Noise Ratio (SNR): the ratio of desired signal to unwanted noise coming from a DUT, expressed in dB.
Crosstalk: the unwanted presence of a signal from one audio channel as it appears in other audio channels of a DUT. Since this is a ratio, it is expressed in dB.
Phase: the relationship in time between two signals of identical frequency, expressed as a fraction of the period of the signal. This is usually expressed in degrees, with one complete cycle of a sinusoidal signal being 360 degrees.
Intermodulation Distortion (IMD): Distortion that is the result of non-linear mixing of two or more signals, typically two sine-waves at different frequencies or the sum of a sine-wave and square-wave. In addition to distortion products at harmonic multiples of the frequencies, products are also found at multiples of the sums and differences of the original frequencies.
Time domain display: Equivalent to an oscilloscope display of the signal, showing instantaneous amplitude as a function of time.

References

This article is issued from Wikipedia - version of the Friday, August 07, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.