Bismuth antimonide

Bismuth antimonide
Identifiers
ChemSpider 11201349
PubChem 6914523
Properties
BiSb
Molar mass 330.74 g/mol
Appearance Faint-grey to dark-grey powder
Density 8.31 g/cm3
Solubility insoluble
Structure
Hexagonal, A7, SpaceGroup = R-3m, No. 166
a = 4.546A, c = 11.860A[1]
Hazards
Safety data sheet
NFPA 704
Flammability code 0: Will not burn. E.g., water Health code 2: Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury. E.g., chloroform Reactivity code 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g., liquid nitrogen Special hazards (white): no codeNFPA 704 four-colored diamond
0
2
0
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
Infobox references

Bismuth antimonides, Bismuth-antimonys, or Bismuth-antimony alloys, (Bi1-xSbx) are binary alloys of bismuth and antimony in various ratios.

Some, in particular Bi0.9Sb0.1, were the first experimentally-observed three-dimensional topological insulators, materials that have conducting surface states but have an insulating interior.[2]

Various BiSb alloys also superconduct at low temperatures,[3] are semiconductors,[4] and are used in thermoelectric devices.[5]

Bismuth antimonide itself (see box to right) is sometimes described as Bi2Sb2.[6]

Synthesis

Crystals of bismuth antimonides are synthesized by melting bismuth and antimony together under inert gas or vacuum. Zone melting is used to decrease the concentration of impurities.[5] When synthesizing single crystals of bismuth antimonides, it is important that impurities are removed from the samples, as oxidation occurring at the impurities leads to polycrystalline growth.[4]

Properties

Topological Insulator

Pure bismuth is a semimetal, containing a small band gap, which leads to it having a relatively high conductivity (7.7*105 S/m at 20 °C). When the bismuth is doped with antimony, the conduction band decreases in energy and the valence band increases in energy. At an Sb concentration of 4%, the two bands intersect, forming a Dirac point[2] (which is defined as a point where the conduction and valence bands intersect). Further increases in the concentration of antimony result in a band inversion, in which the energy of the valence band becomes greater than that of the conduction band at specific momenta. Between Sb concentrations of 7 and 22%, the bands no longer intersect, and the Bi1-xSbx becomes an inverted-band insulator.[7] It is at these higher concentrations of Sb that the band gap in the surface states vanishes, and the material thus conducts at its surface.[2]

Superconductor

The highest temperatures at which Bi.4Sb.6 thin film of thicknesses 150-1350A superconduct, the critical temperature Tc, is approximately 2K.[3] Single crystal Bi.935Sb.065 can superconduct at slightly higher temperatures, and at 4.2K, its critical magnetic field Bc (the maximum magnetic field that the superconductor can expel) of 1.6T at 4.2K.[8]

Semiconductor

Electron mobility is one important parameter describing semiconductors because it describes the rate at which electrons can travel through the semiconductor. At 40K, electron mobility ranged from 0.49*106 cm2/Vs at an Sb concentration of 0 to .24*106 cm2/Vs at a Sb concentration of 7.2%.[4] This is much greater than the electron mobility of other common semiconductors like Si, which is 1400 cm2/Vs at room temperature.[9]

Another important parameter of Bi1-xSbx is the effective electron mass (EEM), a measure of the ratio of the acceleration of an electron to the force applied to an electron. The effective electron mass is .002me for x=.11 and .0009me at x=.06.[2] This is much less than the electron effective mass in many common semiconductors (1.09 in Si at 300K, .55 in Ge, and .067 in GaAs). A low EEM is good for Thermophotovoltaic applications.

Thermoelectric

Bismuth antimonides are used as the n-type legs in many thermoelectric devices below room temperature. The thermoelectric efficiency, given by its figure of merit zT = σS2T/λ, where S is the Seebeck coefficient, λ is the thermal conductivity, and σ is the electrical conductivity, describes the ratio of the energy provided by the thermoelectric to the heat absorbed by the device. At 80K, the figure of merit (zT) for Bi1-xSbx peaks at at 6.5*10−3/K when x = 15%.[5] Also, The Seebeck coefficient (the ratio of the potential difference between ends of a material to the temperature difference between the sides) at 80K of Bi.9Sb.1 is -140μV/K, much smaller than the Seebeck coefficient of pure bismuth, -50μV/K.[10]

References

  1. Jain, A. L. (1959). "Temperature Dependence of the Electrical Properties of Bismuth-Antimony Alloys". Phys. Rev. 115: 1518.
  2. 1 2 3 4 Hsieh, D.; Qian, D.; Wray, L.; Xia, Y.; Hor, Y. S.; Cava, R. J.; Hasan, M. Z. (2008-04-24). "A topological Dirac insulator in a quantum spin Hall phase". Nature 452 (7190): 970–974. doi:10.1038/nature06843. ISSN 0028-0836.
  3. 1 2 Zally, G. D.; Mochel, J. M. "Fluctuation Heat Capacity in Superconducting Thin Films of Amorphous BiSb". Physical Review Letters 27 (25): 1710–1712. doi:10.1103/physrevlett.27.1710.
  4. 1 2 3 Jain, A. L. "Temperature Dependence of the Electrical Properties of Bismuth-Antimony Alloys". Physical Review 114 (6): 1518–1528. doi:10.1103/physrev.114.1518.
  5. 1 2 3 Smith, G. E.; Wolfe, R. (1962-03-01). "Thermoelectric Properties of Bismuth‐Antimony Alloys". Journal of Applied Physics 33 (3): 841–846. doi:10.1063/1.1777178. ISSN 0021-8979.
  6. Bismuth Antimonide
  7. "Phase transition between the quantum spin Hall and insulator phases in 3D: emergence of a topological gapless phase". doi:10.1088/1367-2630/9/9/356.
  8. Kasumov, A. Yu.; Kononenko, O. V.; Matveev, V. N.; Borsenko, T. B.; Tulin, V. A.; Vdovin, E. E.; Khodos, I. I. "Anomalous Proximity Effect in the Nb-BiSb-Nb Junctions". Physical Review Letters 77 (14): 3029–3032. doi:10.1103/physrevlett.77.3029.
  9. "Electrical properties of Silicon (Si)". www.ioffe.rssi.ru. Retrieved 2015-12-11.
  10. Goldsmid, H. J. (1970-01-16). "Bismuth–antimony alloys". physica status solidi (a) 1 (1): 7–28. doi:10.1002/pssa.19700010102. ISSN 1521-396X.
This article is issued from Wikipedia - version of the Monday, January 04, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.