Clamper (electronics)

Not to be confused with voltage clamp.

A clamper is an electronic circuit that fixes either the positive or the negative peak excursions of a signal to a defined value by shifting its DC value. The clamper does not restrict the peak-to-peak excursion of the signal, it moves the whole signal up or down so as to place the peaks at the reference level. A diode clamp (a simple, common type) consists of a diode, which conducts electric current in only one direction and prevents the signal exceeding the reference value; and a capacitor which provides a DC offset from the stored charge. The capacitor forms a time constant with the resistor load which determines the range of frequencies over which the clamper will be effective.

General function

A clamping circuit (also known as a clamper) will bind the upper or lower extreme of a waveform to a fixed DC voltage level. These circuits are also known as DC voltage restorers. Clampers can be constructed in both positive and negative polarities. When unbiased, clamping circuits will fix the voltage lower limit (or upper limit, in the case of negative clampers) to 0 Volts. These circuits clamp a peak of a waveform to a specific DC level compared with a capacitively coupled signal which swings about its average DC level.

Types

Clamp circuits are categorised by their operation; negative or positive, and biased or unbiased. A positive clamp circuit outputs a purely positive waveform from an input signal; it offsets the input signal so that all of the waveform is greater than 0 V. A negative clamp is the opposite of this - this clamp outputs a purely negative waveform from an input signal.

A bias voltage between the diode and ground offsets the output voltage by that amount.

For example, an input signal of peak value 5 V (V_INpeak = 5 V) is applied to a positive clamp with a bias of 3 V (V_BIAS = 3 V), the peak output voltage will be:

V_OUTpeak = 2V_INpeak + V_BIAS

V_OUTpeak = 2 * 5 V + 3 V

V_OUTpeak = 13 V

Positive unbiased

A positive unbiased clamp.

In the negative cycle of the input AC signal, the diode is forward biased and conducts, charging the capacitor to the peak negative value of V_IN. During the positive cycle, the diode is reverse biased and thus does not conduct. The output voltage is therefore equal to the voltage stored in the capacitor plus the input voltage, so V_OUT = V_IN + V_INpeak. This is also called a Villard circuit.

Negative unbiased

A negative unbiased clamp

A negative unbiased clamp is the opposite of the equivalent positive clamp. In the positive cycle of the input AC signal, the diode is forward biased and conducts, charging the capacitor to the peak positive value of V_IN. During the negative cycle, the diode is reverse biased and thus does not conduct. The output voltage is therefore equal to the voltage stored in the capacitor plus the input voltage again, so V_OUT = V_IN - V_INpeak

Positive biased

A positive biased clamp

A positive biased voltage clamp is identical to an equivalent unbiased clamp but with the output voltage offset by the bias amount V_BIAS. Thus, V_OUT = V_IN + (V_INpeak + V_BIAS)

Negative biased

A negative biased clamp

A negative biased voltage clamp is likewise identical to an equivalent unbiased clamp but with the output voltage offset in the negative direction by the bias amount V_BIAS. Thus, V_OUT = V_IN - (V_INpeak + V_BIAS)

Op-amp circuit

Precision op-amp clamp circuit^[2]

The figure shows an op-amp clamp circuit with a non-zero reference clamping voltage. The advantage here is that the clamping level is at precisely the reference voltage. There is no need to take into account the forward volt drop of the diode (which is necessary in the preceding simple circuits as this adds to the reference voltage). The effect of the diode volt drop on the circuit output will be divided down by the gain of the amplifier, resulting in an insignificant error. The circuit also has a great improvement in linearity at small input signals in comparison to the simple diode circuit.

Clamping for input protection

Clamping can be used to adapt an input signal to a device that cannot make use of or may be damaged by the signal range of the original input.

Principles of operation

The schematic of a clamper includes a capacitor, followed by a diode in parallel with the load. The clamper circuit relies on a change in the capacitor's time constant; this is the result of the diode changing current path with the changing input voltage. The magnitude of R and C are chosen so that the time constant, $\tau = RC$ , is large enough to ensure that the voltage across the capacitor does not discharge significantly during the diode's non-conducting interval. However this kind of discharge only happened when the load resistor is very big which takes the capacitor a lot of time to discharge and can be ignored in a high frequency. On the other hand, the capacitor is chosen small enough to allow it to charge quickly during the diode's conducting interval. At the same time, the voltage resource's frequency should be chosen small enough for the capacitor to fully charge in a quarter period.

During the first negative phase of the AC input voltage, the capacitor in the positive clamper charges rapidly. As V_in becomes positive, the capacitor serves as a voltage doubler; since it has stored the equivalent of V_in during the negative cycle, it provides nearly that voltage during the positive cycle; this essentially doubles the voltage seen by the load. As V_in becomes negative, the capacitor acts as a battery of the same voltage of V_in. The voltage source and the capacitor counteract each other, resulting in a net voltage of zero as seen by the load.

Biased versus non-biased

By using a voltage source and resistor, the clamper can be biased to bind the output voltage to a different value. The voltage supplied to the potentiometer will be equal to the offset from zero (assuming an ideal diode) in the case of either a positive or negative clamper (the clamper type will determine the direction of the offset). If a negative voltage is supplied to either positive or negative, the waveform will cross the x-axis and be bound to a value of this magnitude on the opposite side. Zener diodes can also be used in place of a voltage source and potentiometer, hence setting the offset at the Zener voltage.

Examples

Clamping circuits were common in analog television receivers. These sets have a DC restorer circuit, which returns the voltage of the signal during the back porch of the line blanking period to 0 V. Low frequency interference, especially power line hum, induced onto the signal spoils the rendering of the image, and in extreme cases causes the set to lose synchronization. This interference can be effectively removed via this method.

References

↑ Martin Hartley Jones (1995). A Practical Introduction to Electronic Circuits. Cambridge University Press. p. 261. ISBN 978-0-521-47879-3.
↑ S. P. Bali, Linear Integrated Circuits, p.279, Tata McGraw-Hill, 2008 ISBN 0-07-064807-7.

R. M. Marston (1991). Diode, Transistor & Fet Circuits Manual. Newness. pp. 13–17. ISBN 978-1-4831-3540-3.
Rectifier Applications Handbook HB214/D Rev. 2. ON Semiconductor. Nov 2001. pp. 160–161.
J. A. Coekin (1975). High-Speed Pulse Techniques. Pergamon. pp. 60–64. ISBN 978-1-4831-0548-2.

This article is issued from Wikipedia - version of the Tuesday, April 05, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.