Computer memory

In computing, memory refers to the computer hardware devices used to store information for immediate use in a computer; it is synonymous with the term "primary storage". Computer memory operates at a high speed, for example random-access memory (RAM), as a distinction from storage that provides slow-to-access program and data storage but offers higher capacities. If needed, contents of the computer memory can be transferred to secondary storage, through a memory management technique called "virtual memory". An archaic synonym for memory is store.[1]

The term "memory", meaning "primary storage" or "main memory", is often associated with addressable semiconductor memory, i.e. integrated circuits consisting of silicon-based transistors, used for example as primary storage but also other purposes in computers and other digital electronic devices. There are two main kinds of semiconductor memory, volatile and non-volatile. Examples of non-volatile memory are flash memory (used as secondary memory) and ROM, PROM, EPROM and EEPROM memory (used for storing firmware such as BIOS). Examples of volatile memory are primary storage, which is typically dynamic random-access memory (DRAM), and fast CPU cache memory, which is typically static random-access memory (SRAM) that is fast but energy-consuming, offering lower memory areal density than DRAM.

Most semiconductor memory is organized into memory cells or bistable flip-flops, each storing one bit (0 or 1). Flash memory organization includes both one bit per memory cell and multiple bits per cell (called MLC, Multiple Level Cell). The memory cells are grouped into words of fixed word length, for example 1, 2, 4, 8, 16, 32, 64 or 128 bit. Each word can be accessed by a binary address of N bit, making it possible to store 2 raised by N words in the memory. This implies that processor registers normally are not considered as memory, since they only store one word and do not include an addressing mechanism.

Typical secondary storage devices are hard disk drives and solid-state drives.

History

Detail of the back of a section of ENIAC, showing vacuum tubes

In the early 1940s, memory technology mostly permitted a capacity of a few bytes. The first electronic programmable digital computer, the ENIAC, using thousands of octal-base radio vacuum tubes, could perform simple calculations involving 20 numbers of ten decimal digits which were held in the vacuum tube accumulators.

The next significant advance in computer memory came with acoustic delay line memory, developed by J. Presper Eckert in the early 1940s. Through the construction of a glass tube filled with mercury and plugged at each end with a quartz crystal, delay lines could store bits of information in the form of sound waves propagating through mercury, with the quartz crystals acting as transducers to read and write bits. Delay line memory would be limited to a capacity of up to a few hundred thousand bits to remain efficient.

Two alternatives to the delay line, the Williams tube and Selectron tube, originated in 1946, both using electron beams in glass tubes as means of storage. Using cathode ray tubes, Fred Williams would invent the Williams tube, which would be the first random access computer memory. The Williams tube would prove more capacious than the Selectron tube (the Selectron was limited to 256 bits, while the Williams tube could store thousands) and less expensive. The Williams tube would nevertheless prove to be frustratingly sensitive to environmental disturbances.

Efforts began in the late 1940s to find non-volatile memory. Jay Forrester, Jan A. Rajchman and An Wang developed magnetic core memory, which allowed for recall of memory after power loss. Magnetic core memory would become the dominant form of memory until the development of transistor-based memory in the late 1960s.

Developments in technology and economies of scale have made possible so-called Very Large Memory (VLM) computers.[2]

The term "memory" when used with reference to computers generally refers to Random Access Memory or RAM.

Volatile memory

Various memory modules containing different types of DRAM (from top to bottom): DDR SDRAM, SDRAM, EDO DRAM, and FPM DRAM
Main article: Volatile memory

Volatile memory is computer memory that requires power to maintain the stored information. Most modern semiconductor volatile memory is either static RAM (SRAM) or dynamic RAM (DRAM). SRAM retains its contents as long as the power is connected and is easy for interfacing, but uses six transistors per bit. Dynamic RAM is more complicated for interfacing and control, needing regular refresh cycles to prevent losing its contents, but uses only one transistor and one capacitor per bit, allowing it to reach much higher densities and much cheaper per-bit costs.

SRAM is not worthwhile for desktop system memory, where DRAM dominates, but is used for their cache memories. SRAM is commonplace in small embedded systems, which might only need tens of kilobytes or less. Forthcoming volatile memory technologies that aim at replacing or competing with SRAM and DRAM include Z-RAM and A-RAM.

Non-volatile memory

Solid-state drives are one example of non-volatile memory.
Main article: Non-volatile memory

Non-volatile memory is computer memory that can retain the stored information even when not powered. Examples of non-volatile memory include read-only memory (see ROM), flash memory, most types of magnetic computer storage devices (e.g. hard disk drives, floppy disks and magnetic tape), optical discs, and early computer storage methods such as paper tape and punched cards.

Forthcoming non-volatile memory technologies include FeRAM, CBRAM, PRAM, SONOS, RRAM, racetrack memory, NRAM, 3D XPoint, and millipede memory.

Management of memory

Main article: Memory management

Proper management of memory is vital for a computer system to operate properly. Modern operating systems have complex systems to properly manage memory. Failure to do so can lead to bugs, slow performance, and at worst case, takeover by viruses and malicious software.

Nearly everything a computer programmer does requires him or her to consider how to manage memory. Even storing a number in memory requires the programmer to specify how the memory should store it.

Memory management bugs

Improper management of memory is a common cause of bugs, including the following types:

Early computer systems

In early computer systems, programs typically specified the location to write memory and what data to put there. This location was a physical location on the actual memory hardware. The slow processing of such computers did not allow for the complex memory management systems used today. Also, as most such systems were single-task, sophisticated systems were not required as much.

This approach has its pitfalls. If the location specified is incorrect, this will cause the computer to write the data to some other part of the program. The results of an error like this are unpredictable. In some cases, the incorrect data might overwrite memory used by the operating system. Computer crackers can take advantage of this to create viruses and malware.

Virtual memory

Main article: Virtual memory

Virtual memory is a system where all physical memory is controlled by the operating system. When a program needs memory, it requests it from the operating system. The operating system then decides what physical location to place the memory in.

This offers several advantages. Computer programmers no longer need to worry about where the memory is physically stored or whether the user's computer will have enough memory. It also allows multiple types of memory to be used. For example, some memory can be stored in physical RAM chips while other memory is stored on a hard drive. This drastically increases the amount of memory available to programs. The operating system will place actively used memory in physical RAM, which is much faster than hard disks. When the amount of RAM is not sufficient to run all the current programs, it can result in a situation where the computer spends more time moving memory from RAM to disk and back than it does accomplishing tasks; this is known as thrashing.

Virtual memory systems usually include protected memory, but this is not always the case.

Protected memory

Main article: Memory protection

Protected memory is a system where each program is given an area of memory to use and is not permitted to go outside that range. Use of protected memory greatly enhances both the reliability and security of a computer system.

Without protected memory, it is possible that a bug in one program will alter the memory used by another program. This will cause that other program to run off of corrupted memory with unpredictable results. If the operating system's memory is corrupted, the entire computer system may crash and need to be rebooted. At times programs intentionally alter the memory used by other programs. This is done by viruses and malware to take over computers.

Protected memory assigns programs their own areas of memory. If the operating system detects that a program has tried to alter memory that does not belong to it, the program is terminated. This way, only the offending program crashes, and other programs are not affected by the error.

Protected memory systems almost always include virtual memory as well.

See also

Wikimedia Commons has media related to Computer memory.

Footnotes

  1. ↑ A.M. Turing and R.A. Brooker (1952). Programmer's Handbook for Manchester Electronic Computer Mark II. University of Manchester.
  2. ↑ Stanek, William R. (2009). Windows Server 2008 Inside Out. O'Reilly Media, Inc. p. 1520. ISBN 9780735638068. Retrieved 2012-08-20. [...] Windows Server Enterprise supports clustering with up to eight-node clusters and very large memory (VLM) configurations of up to 32 GB on 32-bit systems and 2 TB on 64-bit systems.

References

External links

This article is issued from Wikipedia - version of the Tuesday, April 26, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.