Custer CCW-5

CCW-5
Role 5-seat light transport
National origin USA
Manufacturer Custer Channel Wing Corporation, Hagerstown, Maryland
First flight 13 July 1953[1]
Number built 2
Unit cost
$55,000 in 1955 [2]

The Custer CCW-5 was a twin-engined, 5-seat aircraft of pusher configuration, which used a channel wing claimed to enable low speed flight and short take-offs. Two CCW-5s flew, eleven years apart, but the type never entered production.

The aircraft was the third and last of a series of Custer Channel Wing designs.

Design and development

In most situations an aircraft's lift comes chiefly from the low pressure generated on the upper surface by the locally enhanced higher air velocity. This latter may be the result of the movement of the aircraft through the air or, when lift at low air speeds is important for short take-off performance, produced by engine power. The channel wing, the brainchild of Willard Ray Custer, increased the upper surface velocity in a U-shaped channel formed out of the wing, with a pusher propeller at the trailing edge. This near semi-circular channel laterally constrained the airflow produced by the propeller, even when the aircraft was at rest, producing higher flow velocities than over a conventional pusher wing. The need for wing mounted pusher engines made a pusher twin a natural configuration, and for his third channel wing design Custer chose to modify the existing Baumann Brigadier, a 5-seat mid wing pusher twin which itself did not reach production.[3][4]

Rear view taken in 2004 of the second CCW-5 showing the fixing of the pusher engine within the wing channels.

The CCW-5 retained the fuselage and empennage of the Brigadier, but replaced the whole centre section with a pair of channels, starting at roots in the lower part of the fuselage. Only beyond the channels did the conventional wings regain their mid-wing configuration. A 225 hp (168 kW) Continental O-470 flat six engine was mounted on slender vertical and horizontal struts at the centre of each the channels, on the mid-wing line. These drove constant speed pusher propellers. The main undercarriage was much shortened by mounting its legs on the outer part of the channel section; the Brigadier nosewheel was retained.[3][4]

The first of two CCW-5s flew on 13 July 1953, piloted by Walker Davidson, at Oxnard, California[3][4] and was reported to have completed its test flying by autumn 1956, when production was scheduled to begin.[3] This did not happen, though a second aircraft flew in June 1964.[4] The delay was partly the result of financial problems, though the CCW-5 performed well below the original estimates, with a maximum achieved speed of 220 mph (354 km/h) compared with an estimated 300 mph (480 km/h).[4] It was claimed that the aircraft could fly under control at 11 mph (18 km/h) and that it could take off with a 1,500 lb (680 kg) load at 70% power in 90 ft (28 m).[3]

The second CCW-5 was finished in 1964 with 260 hp (194 kW) Continental IO-470P engines;[2] it survives and is under restoration at the Mid-Atlantic Air Museum, Reading, Pennsylvania.

Specifications

CCW-5

Data from Jane's All the World's Aircraft[3]

General characteristics

Performance


Notes

  1. ↑ Flying Magazine. January 1954. p. 40. Missing or empty |title= (help)
  2. 1 2 Aviation Week. 24 November 1958. Missing or empty |title= (help)
  3. 1 2 3 4 5 6 Bridgman 1956, p. 263
  4. 1 2 3 4 5 6 7 8 9 Aerofiles :Custer
  5. 1 2 3 4 5 American Aviation, 17 November 1958

References

Wikimedia Commons has media related to Custer CCW-5.
  • Allum, Clifford (17 November 1958). "Channel Wing's Second Chance". American Aviation 22 (13): 45. 
  • "Aerofiles: Custer". Retrieved 2010-04-03. 
  • Bridgman, Leonard (1956). Jane's All the World's Aircraft 1956-57. London: Jane's All the World's Aircraft Publishing Co. Ltd. 
This article is issued from Wikipedia - version of the Sunday, January 03, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.