Diethylaluminium chloride

Diethylaluminium chloride
Structural formula of diethylaluminium chloride
Ball-and-stick model of the diethylaluminium chloride molecule
Names
IUPAC name
Chlorodiethylalumane
Other names
Chlorodiethylaluminium
Identifiers
96-10-6 YesY
4123259
ChemSpider 10413126 YesY
EC Number 202-477-2
Jmol interactive 3D Image
PubChem 7277
RTECS number BD0558000
UN number 3394
Properties
C4H10AlCl
Molar mass 120.56 g·mol−1
Density 0.961 g cm−3
Melting point −50 °C (−58 °F; 223 K)
Boiling point 125 to 126 °C (257 to 259 °F; 398 to 399 K) at 50 mmHg
Vapor pressure 3 mmHg (at 60 °C)
Hazards
F C
R-phrases R14/15, R17, R34
S-phrases S26, S36/37/39, S43, S45
NFPA 704
Flammability code 4: Will rapidly or completely vaporize at normal atmospheric pressure and temperature, or is readily dispersed in air and will burn readily. Flash point below 23 °C (73 °F). E.g., propane Health code 3: Short exposure could cause serious temporary or residual injury. E.g., chlorine gas Reactivity code 2: Undergoes violent chemical change at elevated temperatures and pressures, reacts violently with water, or may form explosive mixtures with water. E.g., phosphorus Special hazard W: Reacts with water in an unusual or dangerous manner. E.g., cesium, sodiumNFPA 704 four-colored diamond
4
3
2
Flash point −18 °C (0 °F; 255 K)
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
Infobox references

Diethylaluminium chloride is a highly hazardous organic compound and Lewis acid with the chemical formula C4H10AlCl. When dissolved in hexane, diethylaluminum chloride is a colorless liquid. It is used for polyolefin catalysis and as an intermediate in the preparation of organometallic compounds. It has a vapor density of 4.2 (air=1).[1]

Safety

Diethylaluminum chloride is extremely flammable, and thus must be kept away from sparks, flames, or any source of ignition. The compound must be kept in a tightly closed steel container, in a cool, dry room where temperatures and pressures do not vary frequently, when the compound is not in use.[2] When handling this compound always make sure it is under the fume hood, and, for more protection, always wear a respirator when the container is open. Avoid direct physical contact by always wearing protective gloves, eyewear, and clothing while handing this compound. Those who are not trained to handle such a volatile chemical should not do so for their own safety as diethylaluminum chloride is extremely hard to handle.[3] If a spill of diethylaluminum chloride should occur, first get rid of all ignition sources and prevent water from coming in contact with the spill. Then cover the spill with dry earth or sand, followed by a plastic sheet. Wait until spill can be swept up and dispose of properly.[4]

Effects of exposure and first aid

If diethylaluminum chloride is ingested one may experience burns of the esophagus and stomach. The person may be more likely to vomit or drool. If this happens one can dilute the solution by drinking a lot of water or milk, but no more than 8 ounces. Seek medical attention immediately. If the compound is inhaled burning of the nasal and throat passageways may occur and cause upper airway injury. Should this occur move the person to fresh air, seek medical attention immediately. The medical personnel might administer oxygen or assist in ventilation.[5] Lastly, if the compound comes in contact with the skin or eyes severe skin and eye irritation may occur as well as burns. If it comes in contact with your skin, first remove contaminated clothes, then run skin under water for 15 minutes, finally, if necessary see a physician if burning persists. If the compound comes into contact with the eyes run eyes under copious amounts of water for 30 minutes, then see a doctor immediately.[6]

Reactivity with fire and water

Diethylaluminum chloride vapors can diffuse throughout a room and catch fire from an ignition source and create a flash back. The fire created by diethylaluminum chloride will create very hazardous gases that are toxic when inhaled.[7] To stop a fire created by diethylaluminum chloride, foam, dry chemical, or carbon dioxide should be used. The compound may also re-ignite after extinction because of its high reactivity. Water should never be used to put out the flames as this will cause diethylaluminum chloride to react even more violently. Diethylaluminum chloride is so reactive with water that it may even ignite upon contact with moisture in the air.[8]

References

http://www.chemicaldictionary.org/dic/D/Diethylaluminum-chloride_235.html

http://www.chemcas.org/drug/analytical/cas/96-10-6.asp

Hu, Y. J.; Jiang, H. L.; Wang, H. H., "Preparation of highly branched polyethylene with acenaphthenediimine nickel chloride/diethylaluminum chloride catalyst". Chinese Journal of Polymer Science 2006, 24 (5), 483–488.

Yao, Y. M.; Qi, G. Z.; Shen, Q.; Hu, J. Y.; Lin, Y. H., "Reactivity and structural characterization of divalent samarium aryloxide with diethylaluminum chloride". Chinese Science Bulletin 2003, 48 (20), 2164–2167.

This article is issued from Wikipedia - version of the Wednesday, November 04, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.