Digital elevation model

3D rendering of a DEM of Tithonium Chasma on Mars

A digital elevation model (DEM) is a digital model or 3D representation of a terrain's surface — commonly for a planet (including Earth), moon, or asteroid — created from terrain elevation data.

Terminology

There is no universal usage of the terms digital elevation model (DEM), digital terrain model (DTM) and digital surface model (DSM) in scientific literature. In most cases the term digital surface model represents the earth's surface and includes all objects on it. In contrast to a DSM, the digital terrain model (DTM) represents the bare ground surface without any objects like plants and buildings (see the figure on the right).[1][2]

Surfaces represented by a Digital Surface Model include buildings and other objects. Digital Terrain Models represent the bare ground.

DEM is often used as a generic term for DSMs and DTMs,[3] only representing height information without any further definition about the surface.[4] Other definitions equalise the terms DEM and DTM,[5] or define the DEM as a subset of the DTM, which also represents other morphological elements.[6] There are also definitions which equalise the terms DEM and DSM.[7] On the Web definitions can be found which define DEM as a regularly spaced GRID and a DTM as a three-dimensional model (TIN).[8] Most of the data providers (USGS, ERSDAC, CGIAR, Spot Image) use the term DEM as a generic term for DSMs and DTMs. All datasets which are captured with satellites, airplanes or other flying platforms are originally DSMs (like SRTM or the ASTER GDEM). It is possible to compute a DTM from high resolution DSM datasets with complex algorithms (Li et al., 2005). In the following the term DEM is used as a generic term for DSMs and DTMs.

Types of DEM

Heightmap of Earth's surface (including water and ice) in equirectangular projection, normalized as 8-bit grayscale, where lighter values indicate higher elevation

A DEM can be represented as a raster (a grid of squares, also known as a heightmap when representing elevation) or as a vector-based triangular irregular network (TIN). The TIN DEM dataset is also referred to as a primary (measured) DEM, whereas the Raster DEM is referred to as a secondary (computed) DEM.[9] The DEM could be acquired through techniques such as photogrammetry, lidar, IfSAR, land surveying, etc. (Li et al. 2005). DEMs are commonly built using data collected using remote sensing techniques, but they may also be built from land surveying. DEMs are used often in geographic information systems, and are the most common basis for digitally produced relief maps. While a DSM may be useful for landscape modeling, city modeling and visualization applications, a DTM is often required for flood or drainage modeling, land-use studies,[10] geological applications, and other applications.[11]

Production

Relief map Sierra Nevada

Mappers may prepare digital elevation models in a number of ways, but they frequently use remote sensing rather than direct survey data. One powerful technique for generating digital elevation models is interferometric synthetic aperture radar where two passes of a radar satellite (such as RADARSAT-1 or TerraSAR-X or Cosmo SkyMed), or a single pass if the satellite is equipped with two antennas (like the SRTM instrumentation), collect sufficient data to generate a digital elevation map tens of kilometers on a side with a resolution of around ten meters . Other kinds of stereoscopic pairs can be employed using the digital image correlation method, where two optical images are acquired with different angles taken from the same pass of an airplane or an Earth Observation Satellite (such as the HRS instrument of SPOT5 or the VNIR band of ASTER).[12]

The SPOT 1 satellite (1986) provided the first usable elevation data for a sizeable portion of the planet's landmass, using two-pass stereoscopic correlation. Later, further data were provided by the European Remote-Sensing Satellite (ERS, 1991) using the same method, the Shuttle Radar Topography Mission (SRTM, 2000) using single-pass SAR and the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER, 2000) instrumentation on the Terra satellite using double-pass stereo pairs.[12]

The HRS instrument on SPOT 5 has acquired over 100 million square kilometers of stereo pairs.

Older methods of generating DEMs often involve interpolating digital contour maps that may have been produced by direct survey of the land surface. This method is still used in mountain areas, where interferometry is not always satisfactory. Note that contour line data or any other sampled elevation datasets (by GPS or ground survey) are not DEMs, but may be considered digital terrain models. A DEM implies that elevation is available continuously at each location in the study area.

The quality of a DEM is a measure of how accurate elevation is at each pixel (absolute accuracy) and how accurately is the morphology presented (relative accuracy). Several factors play an important role for quality of DEM-derived products:

Methods for obtaining elevation data used to create DEMs

Uses

Digital Elevation Model - Red Rocks Amphitheater, Colorado obtained using an UAV (DroneMapper)
Bezmiechowa airfield 3D Digital Surface Model obtained using Pteryx UAV flying 200 m above hilltop
Digital Surface Model of motorway interchange construction site. Note that tunnels are closed.
Example DEM flown with the Gatewing X100 in Assenede

Common uses of DEMs include:

Sources

A free DEM of the whole world called GTOPO30 (30 arcsecond resolution, approx. 1 km) is available, but its quality is variable and in some areas it is very poor. A much higher quality DEM from the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) instrument of the Terra satellite is also freely available for 99% of the globe, and represents elevation at 30 meter resolution. A similarly high resolution was previously only available for the United States territory under the Shuttle Radar Topography Mission (SRTM) data, while most of the rest of the planet was only covered in a 3 arc-second resolution (around 90 meters). The limitation with the GTOPO30 and SRTM datasets is that they cover continental landmasses only, and SRTM does not cover the polar regions and has mountain and desert no data (void) areas. SRTM data, being derived from radar, represents the elevation of the first-reflected surface quite often tree tops. So, the data are not necessarily representative of the ground surface, but the top of whatever is first encountered by the radar.

Submarine elevation (known as bathymetry) data is generated using ship-mounted depth soundings. When land topography and bathymetry is combined, a truly Global Relief Model is obtained. The SRTM30Plus dataset (used in NASA World Wind) attempts to combine GTOPO30, SRTM and bathymetric data to produce a truly global elevation model.[16] The Earth2014 global topography and relief model [17] provides layered topography grids at 1 arc-minute resolution. Other than SRTM30plus, Earth2014 provides information on ice-sheet heights and bedrock (that is, topography below the ice) over Antarctica and Greenland. Another global model is Global Multi-resolution Terrain Elevation Data 2010 (GMTED2010) with 7.5 arc second resolution. It is based on SRTM data and combines other data outside SRTM coverage. A novel global DEM of postings lower than 12 m and a height accuracy of less than 2 m is expected from the TanDEM-X satellite mission which started in July 2010.

The most common grid (raster) spacing is between 50 and 500 meters. In gravimetry e.g., the primary grid may be 50 m, but is switched to 100 or 500 meters in distances of about 5 or 10 kilometers.

Since 2002, the HRS instrument on SPOT 5 has acquired over 100 million square kilometers of stereo pairs used to produce a DTED2 format DEM (with a 30-meter posting) DEM format DTED2 over 50 million km².[18] The radar satellite RADARSAT-2 has been used by MacDonald, Dettwiler and Associates Ltd. to provide DEMs for commercial and military customers.[19]

In 2014, acquisitions from radar satellites TerraSAR-X and TanDEM-X will be available in the form of a uniform global coverage with a resolution of 12 meters.[20]

Many national mapping agencies produce their own DEMs, often of a higher resolution and quality, but frequently these have to be purchased, and the cost is usually prohibitive to all except public authorities and large corporations. DEMs are often a product of national lidar dataset programs.

Free DEMs are also available for Mars: the MEGDR, or Mission Experiment Gridded Data Record, from the Mars Global Surveyor's Mars Orbiter Laser Altimeter (MOLA) instrument; and NASA's Mars Digital Terrain Model (DTM).[21]

OpenTopography is a community access resource of high-resolution, Earth science-oriented, topography data, and related tools and resources that warehouses a great deal of DEM data.[22] OpenTopography is based at the San Diego Supercomputer Center at the University of California, San Diego and is operated in collaboration with colleagues in the School of Earth and Space Exploration at Arizona State University. Core operational support for OpenTopography comes from the National Science Foundation Earth Sciences: Instrumentation and Facilities Program (EAR/IF) and the Office of Cyberinfrastructure.

United States

The US Geological Survey produces the National Elevation Dataset, a seamless DEM for the United States, Hawaii and Puerto Rico based on 7.5' topographic mapping. As of the beginning of 2006, this replaces the earlier DEM tiled format (one DEM per USGS topographic map).[23][24]

OpenTopography is a U.S.-based community access source of a large amount of high-resolution topography data for the U.S.[22]

See also

DEM file formats

References

  1. "Intermap Digital Surface Model: accurate, seamless, wide-area surface models".
  2. Li, Z., Zhu, Q. and Gold, C. (2005): title=Digital terrain modeling: principles and methodology|. CRC Press. Boca Raton.
  3. Hirt, C. "Digital Terrain Models.". Encyclopedia of Geodesy: 1–6. doi:10.1007/978-3-319-02370-0_31-1. ISBN 978-3-319-01868-3. Retrieved February 10, 2016.
  4. Peckham, Robert Joseph; Jordan, Gyozo (Eds.)(2007): Development and Applications in a Policy Support Environment Series: Lecture Notes in Geoinformation and Cartography. Heidelberg.
  5. Podobnikar, Tomaz (2008). "Methods for visual quality assessment of a digital terrain model". S.A.P.I.EN.S 1 (2).
  6. "DIN Standard 18709-1".
  7. Adrian W. Graham,Nicholas C. Kirkman,Peter M. Paul (2007): Mobile radio network design in the VHF and UHF bands: a practical approach. West Sussex.
  8. "Landslide Glossary USGS".
  9. RONALD TOPPE (1987): Terrain models — A tool for natural hazard Mapping. In: Avalanche Formation, Movement and Effects (Proceedings of the Davos Symposium, September 1986). IAHS Publ. no. 162,1987
  10. I. Balenovic, H. Marjanovic, D. Vuletic, etc. Quality assessment of high density digital surface model over different land cover classes. PERIODICUM BIOLOGORUM. VOL. 117, No 4, 459–470, 2015.
  11. "Appendix A – Glossary and Acronyms". Severn Tidal Tributaries Catchment Flood Management Plan – Scoping Stage (PDF). UK: Environment Agency.
  12. 1 2 Nikolakopoulos, K. G.; Kamaratakis, E. K; Chrysoulakis, N. (10 November 2006). "SRTM vs ASTER elevation products. Comparison for two regions in Crete, Greece" (PDF). International Journal of Remote Sensing 27 (21): 4819–4838. doi:10.1080/01431160600835853. ISSN 0143-1161. Retrieved June 22, 2010.
  13. James, M.R., Robson, S., 2012, Straightforward reconstruction of 3D surfaces and topography with a camera: Accuracy and geoscience application, Journal of Geophysical Research, v. 117: F03017. DOI: 10.1029/2011JF002289.
  14. Campbell, D. M. H.; White, B.; Arp, P. A. (2013-11-01). "Modeling and mapping soil resistance to penetration and rutting using LiDAR-derived digital elevation data". Journal of Soil and Water Conservation 68 (6): 460–473. doi:10.2489/jswc.68.6.460. ISSN 0022-4561.
  15. I. Balenović, A. Seletković, R. Pernar, A. Jazbec. Estimation of the mean tree height of forest stands by photogrammetric measurement using digital aerial images of high spatial resolution. ANNALS OF FOREST RESEARCH. 58(1), P. 125-143, 2015.
  16. see Martin Gamache's paper on free sources of global data, http://www.terrainmap.com/downloads/Gamache_final_web.pdf
  17. Hirt, C.; Rexer, M. "Earth2014: 1 arc-min shape, topography, bedrock and ice-sheet models - available as gridded data and degree-10,800 spherical harmonics" (PDF). International Journal of Applied Earth Observation and Geoinformation 39: 103–112. doi:10.1016/j.jag.2015.03.001. Retrieved February 20, 2016.
  18. GEO Elevation Services
  19. http://gs.mdacorporation.com/Mapping/DigitalElevationModels.aspx
  20. TerraSAR-X
  21. A basic guide for using Digital Elevation Models with Terragen
  22. 1 2 http://www.opentopography.org/index.php/about/
  23. http://eros.usgs.gov/DEMNotice.html
  24. see Herbert Glarner's paper on using USGS data, http://herbert.gandraxa.com/herbert/dem.asp

Further reading

External links

Data products
This article is issued from Wikipedia - version of the Tuesday, April 19, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.