Dubins path

In geometry, the term Dubins path typically refers to the shortest curve that connects two points in the two-dimensional Euclidean plane (i.e. x-y plane) with a constraint on the curvature of the path and with prescribed initial and terminal tangents to the path, and an assumption that the vehicle traveling the path can only travel forward. If the vehicle can also travel in reverse, then the path follows the Reeds–Shepp curve.^[1]

In 1957, Lester Eli Dubins (1920–2010) ^[2] showed ^[3] using geometrical arguments that any such path will consist of maximum curvature and/or straight line segments. In other words, the shortest path will be made by joining circular arcs of maximum curvature and straight lines. The same result was later shown using Pontryagin's maximum principle.^[4]

The Dubins path is commonly used in the fields of robotics and control theory as a way to plan paths for wheeled robots, airplanes and underwater vehicles. There are simple geometric ^[5] and analytical methods ^[6] to compute the optimal path.

For example, in the case of a wheeled robot, a simple kinematic car model for the systems is:

$\begin{align} \dot x &= V \cos (\theta) \\ \dot y &= V \sin (\theta) \\ \dot \theta &= u \end{align}$

where $(x,y)$ is the car's position, $\theta$ is the heading, the car is moving at a constant speed $V$, and the turn rate control $u$ is bounded. In this case the maximum turning rate corresponds to some minimum turning radius (and equivalently maximum curvature). The prescribed initial and terminal tangents correspond to initial and terminal headings. The Dubins' path gives the shortest path joining two oriented points that is feasible for the wheeled-robot model.

The optimal path type can be described using an analogy with cars of making a 'right turn (R)' , 'left turn (L)' or driving 'straight (S).' An optimal path will always be at least one of the six types: RSR, RSL, LSR, LSL, RLR, LRL. For example, consider that for some given initial and final positions and tangents, the optimal path is shown to be of the type 'RSR.' Then this corresponds to a right-turn arc (R) followed by a straight line segment (S) followed by another right-turn arc (R). Moving along each segment in this sequence for the appropriate length will form the shortest curve that joins a starting point A to a terminal point B with the desired tangents at each endpoint and that does not exceed the given curvature.

• 

  An RSL Dubins path

• 

  An RSR Dubins path

• 

  An LRL Dubins path

References

1. Reeds, J.A. and L.A. Shepp, "Optimal paths for a car that goes both forwards and backwards," Pacific J. Math., 145 (1990), pp. 367–393.
2. "IN MEMORIAM Lester Eli Dubins Professor of Mathematics and Statistics, Emeritus UC Berkeley 1920–2010". University of California. Retrieved 26 May 2012.
3. Dubins, L.E. (July 1957). "On Curves of Minimal Length with a Constraint on Average Curvature, and with Prescribed Initial and Terminal Positions and Tangents". American Journal of Mathematics 79 (3): 497–516. doi:10.2307/2372560.
4. Boissonat, J.D.; A. Cerezo; K. Leblond (May 1992). "Shortest Paths of Bounded Curvature in the Plane". Proceedings of the IEEE International Conference on Robotics and Automation. Piscataway, NJ. pp. 2315–2320. doi:10.1109/ROBOT.1992.220117.
5. Anisi, David (July 2003). "Optimal Motion Control of a Ground Vehicle". Swedish Research Defence Agency. I650-1942.
6. Bui, X.N.; J.D. Boissonnat; P. Soueres; J.P. Laumond (May 1994). "Shortest Path Synthesis for Dubins Non-Holonomic Robot". IEEE Conference on Robotics and Automation. San Diego, CA. pp. 2–7. doi:10.1109/ROBOT.1994.351019.

External links

• Dublins Curves, from Planning Algorithms by Steven M. LaValle