Early Japanese iron-working techniques

Early Japanese iron-working techniques

Introduction

Blast furnaces are thought by many scholars to have developed independently in Western Europe and China, albeit many centuries earlier in the latter.[1] The blast furnace was essential to the development of steel and cast iron, as it allowed much higher temperatures to be reached than its predecessor, the bloomery.[2] Since the blast furnace temperatures were able to exceed 1,536 C, the melting point of iron, the resulting product had significantly less slag (higher purity) than the iron produced by the bloomery.[3] Furthermore, because the temperatures were so low in the bloomeries, only low-carbon steel was able to be produced (wrought iron).[4] As the bloomery began to gradually evolve into the blast furnace during the Middle Ages, many variations on the basic concept began to emerge globally.

Japanese bloomeries

The traditional Japanese furnace, known as a “tatara”, was a hybrid type of furnace. It incorporated bellows, like the European blast furnace, but was constructed of clay; these furnaces would eventually be destroyed after the first use.[5] According to existing archeological records, the first tataras were built during the middle part of the sixth century A.D.[6] Due to the large scale of the tatara, as compared to its European, Indian and Chinese counterparts, the temperature at a given point would vary based on the height in the furnace. Therefore, different types of iron could be found at different heights inside the furnace, ranging from wrought iron at the top of the tatara (furthest from the heat, lowest temperature), to cast iron towards the middle, and finally steel towards the bottom (with varying degrees of carbon content.)[7] Importantly, tataras did not exceed 1500 C, so they did not completely melt the iron.

The metal-workers clearly had an understanding of the differences between the various types of iron found in the tatara, and they separated out and selected different portions of the “bloom” accordingly.[8] In katana forging, for example, only the high- and low- carbon blooms were selected for use. The swordsmiths would then forge the two types of blooms into larger sheets, pound the sheets, fold them on themselves, then repeat this process a minimum of 10 times.[9] Although the chemical process was unknown to them, they were effectively distributing the carbon content of the steel evenly throughout the product, and also distributing the impurities more evenly.[10] This resulted in a product of excellent strength, which had a carbon content higher than that of contemporary European works, but not as high as those found in Indian artifacts.[11]

Transfer of Technology

The tatara bloomery method is considered by historians and archeologists to be unique, and more specifically “an exotic outlier of mainstream metallurgical development.”[12] It has been suggested by scholars that this technology was initially imported from Korea, but the evidence for this is not overwhelming.[13] We can, however, conclude that the Japanese bloomery with its linear design, (in contrast to circular European blast furnaces) certainly resembles many contemporary South Asian designs.[14] The etymology of “tatara” is not Japanese in its origin, which supports the theory that this technology was not locally synthesized.[15]

However, after its adoption, this technology was indeed adapted for local use. While the tatara has commonalities with other South Asian furnace designs, including those of Sri Lanka and Cambodia, the local materials for use in the blast furnace were remarkably different.[16] The main source of ores for Japanese steel was iron sand, a sand-like substance which accumulated as an end product of the erosion of granite and andesite in mountainous regions of Japan.[17] Importantly, it was less labor-intensive to extract the ore from the sand than from hard rock. Furthermore, this sand could be obtained by surface mining, rather than more laborious mining process. However, these sands had a much lower percentage of iron than that typically found in rock-ores, only 2-5% Ferrous Oxide, as compared to 79-87% Ferrous Oxide in certain Sri Lankan ores, for example.[18] Since this smaller percentage of iron would inevitably lead to smaller blooms, Japanese metal workers would have been very familiar with the process of combining blooms. Given these environmental constraints, the most effective solution was to combine certain types of blooms, and through trial-and-error, early sword smiths were able to determine that the most effective combinations of blooms (for swords) were those at the bottom of the tatara.[19]

References

Friedel, R. (2007). Technology in world civilization. Cambridge, MA: MIT Press.

Grazzi, F., Civita, F., Williams, A., Scherillo, A., Barzagli, E., Bartoli, L., Edge, D., & Zoppi, M. (2011). Ancient and historic steel in Japan, India and Europe, a non-invasive comparative study using thermal neutron diffraction. Analytical and Bioanalytical Chemistry, 400(5), 1493-1500. doi: 10.1007/s00216-011-4854-1

Inoue, T. (2009). Tatara and the Japanese sword: the science and technology. Acta Mechanica, 214(N1-2), 17-30. doi: 10.1007/s00707-010-0308-7

Juleff, G. (2009). Technology and evolution: a root and branch view of Asian iron from first-millennium bc Sri Lanka to Japanese steel. World Archeology, 41(4), 557-577. doi: 10.1080/00438240903345688

Wittner, D. (2007). Technology and the culture of progress in meiji Japan. (pp. 24–26). New York, NY: Routledge.

Citations

  1. ↑ Technology in world civilization. P.82
  2. ↑ Technology in world civilization. P.82
  3. ↑ Technology in world civilization. P.82
  4. ↑ Ancient and historic steel in Japan, India and Europe, a non-invasive comparative study using thermal neutron diffraction. Analytical and Bioanalytical Chemistry. P.1497
  5. ↑ Technology and the culture of progress in meiji japan. P.25
  6. ↑ Technology and evolution: a root and branch view of asian iron from first-millennium bc sri lanka to japanese steel. P.573
  7. ↑ Ancient and historic steel in japan, india and europe, a non-invasive comparative study using thermal neutron diffraction. Analytical and Bioanalytical Chemistry. P.1494
  8. ↑ Tatara and the japanese sword: the science and technology. P.19
  9. ↑ Tatara and the japanese sword: the science and technology. P.19
  10. ↑ Ancient and historic steel in japan, india and europe, a non-invasive comparative study using thermal neutron diffraction. Analytical and Bioanalytical Chemistry. P.1494
  11. ↑ Ancient and historic steel in japan, india and europe, a non-invasive comparative study using thermal neutron diffraction. Analytical and Bioanalytical Chemistry. P.1497
  12. ↑ Technology and evolution: a root and branch view of asian iron from first-millennium bc sri lanka to japanese steel. P.574
  13. ↑ Technology and evolution: a root and branch view of asian iron from first-millennium bc sri lanka to japanese steel. P.573
  14. ↑ Technology and evolution: a root and branch view of asian iron from first-millennium bc sri lanka to japanese steel. P.573
  15. ↑ Tatara and the japanese sword: the science and technology. P.19
  16. ↑ Technology and the culture of progress in meiji japan. P.24
  17. ↑ Technology and the culture of progress in meiji japan. P.24
  18. ↑ Technology and evolution: a root and branch view of asian iron from first-millennium bc sri lanka to japanese steel. P.561
  19. ↑ Tatara and the japanese sword: the science and technology. P.19
This article is issued from Wikipedia - version of the Sunday, December 21, 2014. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.