Electrical treeing

A 3D "Electrical Tree" (or Lichtenberg figure), imbedded within a 1.5" cube of Polymethyl Methacrylate (PMMA)

In electrical engineering, treeing is an electrical pre-breakdown phenomenon in solid insulation. It is a damaging process due to partial discharges and progresses through the stressed dielectric insulation, in a path resembling the branches of a tree. Treeing of solid high-voltage cable insulation is a common breakdown mechanism and source of electrical faults in underground power cables.

Other occurrences and causes

Electrical treeing first occurs and propagates when a dry dielectric material is subjected to high and divergent electrical field stress over a long period of time. Electrical treeing is observed to originate at points where impurities, gas voids, mechanical defects, or conducting projections cause excessive electrical field stress within small regions of the dielectric. This can ionize gases within voids inside the bulk dielectric, creating small electrical discharges between the walls of the void. An impurity or defect may even result in the partial breakdown of the solid dielectric itself. Ultraviolet light and ozone from these partial discharges (PD) then react with the nearby dielectric, decomposing and further degrading its insulating capability. Gases are often liberated as the dielectric degrades, creating new voids and cracks. These defects further weaken the dielectric strength of the material, enhance the electrical stress, and accelerate the PD process.

Water trees and electrical trees

In the presence of water, a diffuse, partially conductive 3D plume-like structure, called a water tree, may form within the polyethylene dielectric used in buried or water-immersed high voltage cables. The plume is known to consist of a dense network of extremely small water-filled tubules. Individual tubules are extremely difficult to see using optical magnification, so their study usually requires using a scanning electron microscope (SEM). Water trees begin as a microscopic region near a defect. They then grow under the continued presence of a high electrical field and water. Water trees may eventually grow to the point where they bridge the outer ground layer to the center high voltage conductor, leading to complete electrical failure at that point. Another type of tree-like structure can form with or without the presence of water. Called an electrical tree, it also forms within a polyethylene dielectric (as well as many other solid dielectrics). Electrical trees also originate where bulk or surface defects create excessive electrical stress that initiates dielectric breakdown in a small region. This permanently damages the insulating material in that region. Further tree growth then occurs through as additional small electrical breakdown events (called partial discharges). Electrical tree growth may be accelerated by rapid voltage changes, such as utility switching operations. Also, cables carrying high voltage DC may also develop trees over time as electrical charges migrate into the dielectric nearest the HV conductor. The region of injected charge (called a space charge) amplifies the electrical field in the remaining dielectric, stimulating further tree growth. Since the tree itself is typically partially conducting, its presence also increases the electrical stress in the region between the tree and the opposite conductor. Unlike water trees, the individual channels of electrical trees are larger and more easily seen. Some trees may initially start out as water trees, and then evolve into electrical trees. [1][2] Treeing has been a long-term failure mechanism for buried polymer-insulated high voltage power cables, first reported in 1969.[3] In a similar fashion, 2D trees can occur along the surface of a highly stressed dielectric, or across a dielectric surface that has been contaminated by dust or mineral salts. Over time, these partially conductive trails can grow until they cause complete failure of the dielectric. Electrical tracking, sometimes called dry banding, is a typical failure mechanism for electrical power insulators that are subjected to salt spray contamination along coastlines. The branching 2D and 3D patterns are sometimes called Lichtenberg figures.

2D carbonized electrical trees (or tracking) across the surface of a polycarbonate plate that was part of a trigatron. These partially conducting paths ultimately led to premature breakdown and operational failure of the device

Electrical treeing or "Lichtenberg figures" also occur in high-voltage equipment just before breakdown. Following these Lichtenberg figures in the insulation during postmortem investigation of the broken down insulation can be most useful in finding the cause of breakdown. An experienced high-voltage engineer can see from the direction and the type of trees and their branches where the primary cause of the breakdown was situated and possibly find the cause. Broken-down transformers, high-voltage cables, bushings, and other equipment can usefully be investigated in this way; the insulation is unrolled (in the case of paper insulation) or sliced in thin slices (in the case of solid insulation systems), the results are sketched and photographed and form a useful archive of the breakdown process.

Types of electrical trees

Electrical trees can be further categorized depending on the different tree patterns. These include dendrites, branch type, bush type, spikes, strings, bow-ties and vented trees. The two most commonly found tree types are bow-tie trees and vented trees.[4]

Bow-tie trees
Bow-tie trees are trees which start to grow from within the dielectric insulation and grow symmetrically outwards toward the electrodes. As the trees start within the insulation, they have no free supply of air which will enable continuous support of partial discharges. Thus, these trees have discontinuous growth, which is why the bow-tie trees usually do not grow long enough to fully bridge the entire insulation between the electrodes, therefore causing no failure in the insulation.
Vented trees
Vented trees are trees which initiate at an electrode insulation interface and grow towards the opposite electrode. Having access to free air is a very important factor for the growth of the vented trees. These trees are able to grow continuously until they are long enough to bridge the electrodes, therefore causing failure in the insulation.

Detection and location of electrical trees

Electrical trees can be detected and located by means of partial discharge measurement.

As the measurement values of this method allow no absolute interpretation, data collected during the procedure is compared to measurement values of the same cable gathered during the acceptance-test. This allows simple and quick classification of the dielectric condition (new, strongly aged, faulty) of the cable under test.

To measure the level of partial discharges, a sinusoidal 0.1 Hz VLF (very low frequency) voltage may be used, just as it is used with VLF cable testing. Also available, and more accurate, is a sinusoidal AC source at the power frequency (50-60 Hz) as mandated by IEEE standards 48, 404, 386, and ICEA standards S-97-682, S-94-649 and S-108-720. Modern PD-detection systems employ personal computer-based software for analysis and display of measurement results, and a PD-detector. By the so-called time domain reflectometry (TDR) method the PD-detector measures partial discharge activity. The partial discharge intensity is measured in picoCoulombs (pC) and displayed versus time.

A fully automatic analysis of the reflectograms collected during the measurement allows the location of insulation irregularities and electrical trees. Usually they are displayed in a partial discharge mapping format. Additional useful information about the device under test can be derived from a phase related depiction of the partial discharges.

A sufficient measurement report contains:

See also

References

  1. ↑ E. Moreau; C. Mayoux; C. Laurent (February 1993), "The Structural Characteristics of Water Trees in Power Cables and Laboratory Specimens", IEEE Transactions on Electrical Insulation (IEEE) 28 (1)
  2. ↑ Simmons, M. (2001). "Section 6.6.2". In Ryan, Hugh M. High Voltage Engineering and Testing (Second ed.). The Institution of Electrical Engineers. p. 266. ISBN 0 85296 775 6.
  3. ↑ T. Miyashita, Deterioration of Water-immersed Polyethylene Coated Wire by Treeing publication=Proceedings 1969 IEEE-NEMA Electrical Insulation Conference
  4. ↑ Thue, William A. (1997). Electrical Insulation in Power Systems. CRC. pp. 255–256. ISBN 0-8247-0106-2.

External links

This article is issued from Wikipedia - version of the Friday, April 29, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.