Flywheel storage power system

Sectional view of a flywheel storage with magnetic bearings and evacuated housing

A flywheel-storage power system uses a flywheel for energy storage, (see Flywheel energy storage) and can be a comparatively small storage facility with a peak power of up to 20 MW. It typically is used to stabilize to some degree power grids, to help them stay on the grid frequency, and to serve as a short-term compensation storage. Unlike common storage power plants, such as the pumped storage power plants with capacities up to 1000 MW, the benefits from flywheel storage power plants can be obtained with a facility in the range of a few kW to several 10 MW. [1] They are comparable in this application with battery storage power plants.

Possible areas of application are places where electrical energy can be obtained and stored, and must be supplied again to compensate for example, fluctuations in the seconds range in wind or solar power. These storage facilities consist of individual flywheels in a modular design. Energy up to 150 kW can be absorbed or released per flywheel. Through combinations of several such flywheel accumulators, which are individually housed in buried underground vacuum tanks, a total power of up to several 10 MW can be achieved. The electrical connections power low voltage motors via a DC intermediate circuit and the power converter systems are comparable to those found in plants used in the high-voltage direct current transmissions application. [2]

Sometimes battery storage power stations are built with flywheel storage power systems in order to conserve battery power. Flywheels can handle rapid fluctuations better.[3][4]

Application examples

In vehicles small storage of power flywheels are used as an additional mechanism with batteries, to store the braking energy by regeneration. Power can be stored in the short term and then released back into the acceleration phase of a vehicle with very large electrical currents. This conserves battery power. [5]

Flywheel storage for trams are a good application. During braking (such as when arriving at a station), high energy peaks are found which can not be always fed back into the power grid due to overloading danger. The flywheel energy storage power plants are in containers on side of the tracks and take the excess electrical energy. For example, to 200 000 kWh energy per brake system are annually recovered in Zwickau.[6]

In Stephentown, New York, Beacon Power operates in a flywheel storage power plant with 200 flywheels of 25 kWh capacity and 100 kW of power, Ganged together this gives 5 MWh capacity and 20 MW of power. The units operate at a peak speed at 15,000 rpm. The rotor flywheel consists of wound CFRP fibers which are filled with resin. The installation is intended primarily for frequency control. This service is sold to the New York power grid.[7]

Stadtwerke München (SWM, Munich, Germany) uses a flywheel storage power system to stabilize the power grid, as well as control energy and to compensate for deviations from renewable energy sources. The plant originates from the Jülich Stornetic GmbH. The system consists of 28 flywheels and has a capacity of 100 kWh and a capacity of 600 kilovolt-amperes (kVA). The flywheels rotate at a peak speed of 45,000 rpm.[8]

In Ontario, Canada, Temporal Power Ltd. has operated a flywheel storage power plant since 2014. It consists of 10 flywheels made of steel. Each flywheel weighs four tons and is 2.5 meters high. The maximum number of revolutions is at 11,500 revolutions per minute. The maximum power is 2 MW. The system is used for frequency regulation. After a successful three-year trial period, the system is to be expanded to 20MW and 100MW.[9]

On the island of Aruba is currently a 5MW flywheel storage power plant built by Temporal Power Ltd. The island of Aruba intends to convert its energy supply to 100 percent renewables by 2020.[10]

The city or Fresno in California is running flywheel storage power plants built by Amber Kinetics to store solar energy, which is produced in excess quantity in the daytime, for consumption at night. [11]

Energy loss

It is now possible to build a flywheel storage system that loses just 5 percent of the energy stored in it, per day (i.e.the self-discharge rate).[12]

References

  1. ↑ Schwungrad-Speicherkraftwerk in Hazle Township, Pennsylvania (USA), Betreiberseite beaconpower
  2. ↑ Power Electronics, Darstellung der Leistungselektronik, Betreiberseite beaconpower
  3. ↑ zdf-video, ZDF - Planet E - Schwungradspeicher
  4. ↑ utilitydive.com, PG&E contracts for 75 MW of energy storage which is planned to be increased to 580 MW of capacity
  5. ↑ zdf-video, ZDF - Planet E - Schwungradspeicher
  6. ↑ zdf-video, ZDF - Planet E - Schwungradspeicher, Minute 17:03
  7. ↑ cleanthinking.de BEACON Power, USA
  8. ↑ aachener-zeitung.de Stadtwerke München vermarkten Jülicher Speicher
  9. ↑ thestar.com Ontario electricity gets taken for a spin
  10. ↑ issuu.com Innovative Flywheel Project Supports Aurba's Move to 100% Renewable Energy
  11. ↑ kvpr.org Fresno Project To Store Solar Electricity Using Flywheel
  12. ↑ zdf-video, ZDF - Planet E - Schwungradspeicher, Minute 24:35
This article is issued from Wikipedia - version of the Wednesday, May 04, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.