Bottled gas

Bottled gas is a term used for substances which are gaseous at standard temperature and pressure (STP) and have been compressed and stored in carbon steel, stainless steel, aluminum, or composite bottles known as gas cylinders.

Gas state in cylinders

There are four cases: either the substance remains a gas at standard temperature but increased pressure, the substance liquefies at standard temperature but increased pressure, the substance is dissolved in a solvent, or the substance is liquefied at reduced temperature and increased pressure. In the last case the bottle is constructed with an inner and outer shell separated by a vacuum (dewar flask) so that the low temperature can be maintained by evaporative cooling.

Case I

The substance remains a gas at standard temperature and increased pressure, its critical temperature being below standard temperature. Examples include:

Case II

Butane gas cylinder

modest Tea Kettle boiling water over small Bottled gas at a tea house.

The substance liquefies at standard temperature but increased pressure. Examples include:

ammonia
butane
carbon dioxide (also packaged as a cryogenic gas, Case IV)
chlorine
nitrous oxide
propane
sulfur dioxide

Case III

The substance is dissolved at standard temperature in a solvent. Examples include:

acetylene
- Note: Acetylene cylinders contain an inert packing material, which may be agamassan, and are filled with a solvent such as acetone or dimethylformamide. The acetylene is pumped into the cylinder and it dissolves in the solvent. When the cylinder is opened the acetylene comes back out of solution, much like a carbonated beverage bubbles when opened. This is a workaround to acetylene's property to explode when pressurized above 200 kPa or liquified.

Case IV

The substance is liquefied at reduced temperature and increased pressure. These are also referred to as cryogenic gases. Examples include:

liquid nitrogen (LN₂)
liquid hydrogen (LH₂)
liquid oxygen (LO_X)
carbon dioxide (also packaged as a liquefied gas, Case II)

Note: cryogenic gases are typically equipped with some type of 'bleed' device to prevent overpressure from rupturing the bottle and to allow evaporative cooling to continue.

Expansion and volume

The general rule is that one unit volume of liquid will expand to approximately 800 unit volumes of gas at Standard temperature and pressure with some variation due to intermolecular force and molecule size compared to an ideal gas. Normal high pressure gas cylinders or bottles will hold from 200 to 400 atmosphere (unit)s. The atmosphere units pressure held by the bottle is equivalent to the number of volumes of standard temperature and pressure of the gas held by the bottle for an ideal gas.

Special handling considerations

Because the contents are under high pressure and are sometimes hazardous, there are special safety regulations for handling bottled gases. These include chaining bottles to prevent falling and breaking, proper ventilation to prevent injury or death in case of leaks and signage to indicate the potential hazards.

In the United States, the Compressed Gas Association (CGA) sells a number of booklets and pamphlets on safe handling and use of bottled gases. (Members of the CGA can get the pamphlets for free.) The European Industrial Gases Association and the British Compressed Gases Association provide similar facilities in Europe and the United Kingdom.

Nomenclature differences

In the United States, 'bottled gas' typically refers to liquefied petroleum gas. 'Bottled gas' is sometimes used in medical supply, especially for portable oxygen tanks. Packaged industrial gases are frequently called 'cylinder gas', though 'bottled gas' is sometimes used.

The United Kingdom and other parts of Europe more commonly refer to 'bottled gas' when discussing any usage whether industrial, medical or liquefied petroleum. However, in contrast, what the United States calls liquefied petroleum gas is known generically in the United Kingdom as 'LPG'; and it may be ordered using by one of several Trade names, or specifically as butane or propane depending on the required heat output.

Colour coding

Different countries have different gas colour codes but attempts are being made to standardise the colours of cylinder shoulders:

Colours of cylinders for Medical gases are covered by an International Organization for Standardization (ISO) standard, ISO 32; but not all countries use this standard.
Within Europe gas cylinders colours are being standardised according to EN 1089-3, the standard colours applying to the cylinder shoulder only; i.e., the top of the cylinder close to the pillar valve.
In the United States, colour-coding is not regulated by law.

The user should not rely on the colour of a cylinder to indicate what it contains. The label or decal should always be checked for product identification.

European cylinder colours

The colours below are specific shades, defined in the European Standard^[1]^[2]^[3] in terms of RAL coordinates. The requirements are based on a combination of a few named gases, otherwise on the primary hazard associated with the gas contents:

Specifically named gases

Acetylene cylinders are maroon.
Argon cylinders have a dark green shoulder.
Carbon dioxide cylinders have a grey shoulder.
Chlorine cylinders have a yellow shoulder.
Helium cylinders have a brown shoulder.
Hydrogen cylinders have a red shoulder.
Nitrous oxide cylinders have a blue shoulder.
Nitrogen cylinders have a black shoulder. (Previously grey, in the United Kingdom).
Oxygen cylinders have a white shoulder. (Previously black, in the United Kingdom).

Based on gas properties

Toxic or corrosive gas cylinders have a yellow shoulder (e.g., ammonia, chlorine, fluorine, arsine, carbon monoxide, and sulfur dioxide).
Flammable gas cylinders have a red shoulder (e.g., hydrogen, methane, ethylene, and forming gas).
Oxidising gas cylinders have a light blue shoulder (e.g., nitrous oxide, and oxygen-containing blends).
Inert (nontoxic, nonflammable, nonoxidising) gas cylinders have a bright green shoulder (e.g., neon, krypton, and xenon).
Toxic and flammable or toxic and corrosive gas cylinders have yellow and red shoulders (either two bands or quartered).
Toxic and oxidising or corrosive and oxidising gas cylinders have yellow and light blue shoulders (either two bands or quartered).

Gas mixtures, mostly for diving

Diving cylinders are left unpainted (for aluminium), or painted to prevent corrosion (for steel), often in bright colors, most often yellow, to increase visibility. This should not be confused with industrial gases, where a yellow shoulder means chlorine.

Air diving cylinders have a white and black quartered shoulder or a white top and black band.
Nitrox cylinders, a diving mixture of nitrogen and oxygen, have a white and black quartered shoulder or white top and black band. Can also be coded with green stripe on yellow bottom.
Heliox cylinders, a diving mixture of helium and oxygen, have a white and brown quartered shoulder.
Trimix cylinders, a diving mixture of helium, nitrogen and oxygen, have a white, black and brown segmented shoulder.

References

Notes

Standards

ISO 32: Gas cylinders for medical use—Marking for identification of content.
CEN EN 1089-3: Transportable gas cylinders, Part 3 - Colour Coding.

External links

This article is issued from Wikipedia - version of the Friday, March 11, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.