German aircraft carrier I (1915)

Line-drawing of the proposed aircraft carrier
Class overview
Name: I
Builders: Blohm & Voss
Preceded by: none
Succeeded by: Graf Zeppelin class
Planned: 1
Cancelled: 1
General characteristics
Type: aircraft carrier
Displacement: 12,585 metric tons
Length: 158 m (518 ft)
Beam: 18.8 m (62 ft)
Draft: 7.43 m (24.4 ft)
Propulsion:
  • 2-shaft Blohm & Voss geared turbines
  • 14,000 shp
  • 1,500 tons of coal
Speed: 20 knots
Aircraft carried:
  • 13 or 19 seaplanes
  • 10 wheeled aircraft
Aviation facilities: 3 hangars

The aircraft carrier I[Note 1] was the first planned aircraft carrier conversion project of the German Imperial Navy (Kaiserliche Marine) during World War I. The Imperial Navy had experimented previously with seaplane carriers, though these earlier conversions were too slow to operate with the High Seas Fleet and carried an insufficient number of aircraft. I was intended to carry between 23 and 30 aircraft, including fighters, bombers, and torpedo-bombers.

The ship was based on the incomplete hull of the Italian passenger ship Ausonia, which was being built in Hamburg. The conversion was proposed by the Air Department of the Reichs Navy Office, but it was abandoned after negotiations within the German Navy over a proposed moratorium on new ships at the end of the war. After World War I ended, high inflation in Germany added to the cost of the ship, and as a result, the Italian shipping company for whom the ship was originally built, declined to purchase her. The vessel was therefore sold to shipbreakers and dismantled in 1922.

Design

Ausonia began her existence as a turbine-powered passenger steamer, ordered by Italian Sitmar in 1914. The ship was built in the Blohm & Voss shipyard in Hamburg, under construction number 236.[1] At the time, the only German seaplane carrier was the armored cruiser Friedrich Carl, which carried two planes.[2] The leadership of the German Navy believed that zeppelins were much more effective than seaplanes, both for reconnaissance and attack.[3] Admiral Alfred von Tirpitz, the architect of the German Navy, was particularly unimpressed by the performance of fixed-wing aircraft.[4] Nevertheless, the Navy developed several naval aircraft before and during the war, including a pair of seaplane fighters, the W.12 and the W.29, both built by Hansa-Brandenburg. Twin-engined torpedo-floatplanes were also designed.[5]

Regardless of the preference toward airships, several small merchant vessels were converted into seaplane carriers during World War I. They carried only two to four aircraft each, however, and were too slow to operate with the High Seas Fleet. The light cruiser Stuttgart, which was fast enough to steam with the Fleet, was converted into a seaplane carrier in 1918. She too, though, only carried two seaplanes. It was decided to convert the liner Ausonia into a flight-deck carrier for wheeled aircraft as well as floatplanes.[6] The plan for the conversion was drawn up by Leutnant zur See Jürgen Reimpell in 1918, an officer of the 1st Aviation Detachment.[7]

General characteristics

Once converted, I was to have been 158 meters long overall and 149.6 m long between perpendiculars. The ship had a beam of 18.8 m and a draft of 7.43 m, and displaced 12,585 metric tons. The ship was powered by two sets of Blohm & Voss geared turbines that drove a pair of screws, the diameter of which is not known. The details of the boiler system and electrical power plant are unknown.[1]

The ship was to have been equipped with two 82 m-long hangar decks for wheeled aircraft and a third 128 m-long hangar deck for seaplanes; all of the hangars were 18.5 m wide. The flight deck would have been 128.5 m long and 18.7 m wide. All three of the hangars and flight deck were intended to have been mounted above the main structural deck. The ship's designers intended to mount a take off deck on the bow, which would have been 30 m long and 10.5 m wide. According to naval historian Erich Gröner, the ship was designed to carry either 13 fixed-wing or 19 folding-wing seaplanes, along with around 10 wheeled aircraft.[1] Rene Greger estimated the ship to carry eight to ten fighter aircraft and a combination of fifteen to twenty bombers and torpedo-floatplanes.[6]

Conversion

I was launched as the passenger ship Ausonia on 15 April 1915. While the ship was still being fitted out, the German navy decided to convert the ship into an aircraft carrier. The proposed design was completed by 1918, but by then, the majority of naval construction efforts were diverted to building new U-boats.[1] The demands on labor and resources the war imposed on the German economy reduced the shipbuilding industry to barely being able to cover the maintenance and repair needs of the High Seas Fleet. What resources were left over were by 1918 funneled into U-boat production.[8] As a result of the growing importance of U-boat construction and a moratorium on new surface ships imposed by the Reichsmarineamt (RMA the Imperial Navy Office), the conversion project was abandoned.[1]

The design influenced the planned conversion of the armored cruiser SMS Roon into a seaplane carrier. This plan too, however, was scrapped.[1] In 1920, the Italian shipping company canceled its order for Ausonia because the post-war inflation in Germany substantially increased the price of the ship. As a result, she was sold to ship breakers in 1922 and broken up for scrap.[1]

Footnotes

Notes
  1. "I" was the provisional name for the ship under which she was ordered; had she been completed she would have been assigned an actual name.
Citations
  1. 1 2 3 4 5 6 7 Gröner, p. 70
  2. Greger, p. 87
  3. Herwig, pp. 214215
  4. Herwig, p. 213
  5. Herwig, pp. 212213
  6. 1 2 Greger, p. 88
  7. Schenk, p. 129
  8. Weir, pp. 178179

References

This article is issued from Wikipedia - version of the Tuesday, March 08, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.