Germicidal lamp

A 9W germicidal lamp in a modern compact fluorescent lamp form factor

UV-C LED Lamp with Heatsink and power source

Glow of a germicidal lamp excited by a high voltage probe.

Close-up of the electrodes and the safety warning

A germicidal lamp is a special type of lamp which produces ultraviolet light (UVC). This short-wave ultraviolet light disrupts DNA base pairing causing thymine-thymine dimers leading to death of bacteria on exposed surfaces. It can also be used to produce ozone for water disinfection.

There are three common types available:

• LED lamps
• Low pressure lamps
• Medium pressure lamps

LEDs

Light Emitting Diodes (LEDs) have been developed in the UV-C range and products implementing these devices have begun to surface. UV-C LEDs have selective wavelengths between 240 - 280 nm allowing for disinfection targeted at specific pathogens or applications.^[1]

LED lamps emit only light at the front of the device and all heat is emitted towards the back providing no effect on the water temperature and not promoting fouling.

UV-C LED lamps require less power than conventional mercury lamps and use direct current (DC) allowing for battery and solar power options for remote communities and mobile applications.

Because of the size of UV-C LEDs the system can be designed much smaller, in some cases 6 times smaller than conventional UV systems. LED systems do not require a ballast further reducing the size needed.

Low pressure lamps

Low-pressure lamps are very similar to a fluorescent lamp, with a wavelength of 253.7 nm (1182.5 THz).

The most common form of germicidal lamp looks similar to an ordinary fluorescent lamp but the tube contains no fluorescent phosphor. In addition, rather than being made of ordinary borosilicate glass, the tube is made of fused quartz. These two changes combine to allow the 253.7 nm ultraviolet light produced by the mercury arc to pass out of the lamp unmodified (whereas, in common fluorescent lamps, it causes the phosphor to fluoresce, producing visible light). Germicidal lamps still produce a small amount of visible light due to other mercury radiation bands.

An older design looks like an incandescent lamp but with the envelope containing a few droplets of mercury. In this design, the incandescent filament heats the mercury, producing a vapor which eventually allows an arc to be struck, short circuiting the incandescent filament.

At the last two decades the rapid development is acquired so-called excimer lamps having a number of advantages over the other sources of ultraviolet and even vacuum ultraviolet radiation.

Medium pressure lamps

Medium-pressure lamps are much more similar to HID lamps than fluorescent lamps.

These lamps radiate a broad-band UV-C radiation, rather than a single line. They are widely used in industrial water treatment, because they are very intense radiation sources. They are as efficient as low-pressure lamps. Medium-pressure lamps produce very bright bluish white light.

Auxiliary equipment

As with all gas discharge lamps, all of the styles of germicidal lamps exhibit negative resistance and require the use of an external ballast to regulate the current flow through them. The older lamps that resembled an incandescent lamp were often operated in series with an ordinary 40 W incandescent "appliance" lamp; the incandescent lamp acted as the ballast for the germicidal lamp.

Uses

Germicidal lamps are used to sterilize workspaces and tools used in biology laboratories and medical facilities. If the quartz envelope transmits wavelengths shorter than 253.7 nm, they can also be used wherever ozone is desired, for example, in the sanitizing systems of hot tubs and aquariums. They are also used by geologists to provoke fluorescence in mineral samples, aiding in their identification. In this application, the light produced by the lamp is usually filtered to remove as much visible light as possible, leaving just the UV light.

An EPROM. The small quartz window allows UV light to enter during erasure.

The light produced by germicidal lamps is also used to erase EPROMs; the ultraviolet photons are sufficiently energetic to allow the electrons trapped on the transistors' floating gates to tunnel through the gate insulation, eventually removing the stored charge that represents binary ones and zeroes.

Germicidal lamps are also used in waste water treatment in order to kill microorganisms.

Ozone production

For most purposes, ozone production would be a detrimental side effect of lamp operation. To prevent this, most germicidal lamps are treated to absorb the 185 nm mercury emission line (which is the longest wavelength of mercury light which will ionize oxygen).

In some cases (such as water sanitization), ozone production is precisely the point. This requires specialized lamps which do not have the surface treatment.

Safety concerns

Short-wave UV light is harmful to humans. In addition to causing sunburn and (over time) skin cancer, this light can produce extremely painful inflammation of the cornea of the eye, which may lead to temporary or permanent vision impairment. It can also damage the retina of the eye. For this reason, the light produced by a germicidal lamp must be carefully shielded against both direct viewing and reflections and dispersed light that might be viewed.

References

1. Aquisense. "UV-C LED Technology". AquiSense Technologies. Retrieved 2016-04-25.

External links