ISO/IEC 9995

ISO/IEC 9995 Information technology — Keyboard layouts for text and office systems is an ISO standard series defining layout principles for computer keyboards. It does not define specific layouts but provides the base for national and industry standards which define such layouts.

The project of this standard was adopted at ISO in Berlin in 1985 under the proposition of Dr Yves Neuville. The ISO/IEC 9995 standard series dates to 1994 and has undergone several updates over the years.

Parts

The ISO/IEC 9995 standard series currently (as of September 2015) consists of the following parts:

ISO/IEC 9995-1:2009 General principles governing keyboard layouts^[1]
ISO/IEC 9995-2:2009 Alphanumeric section^[2] with Amendment 1 (2012) Numeric keypad emulation^[3]
ISO/IEC 9995-3:2010 Complementary layouts of the alphanumeric zone of the alphanumeric section^[4]
ISO/IEC 9995-4:2009 Numeric section^[5]
ISO/IEC 9995-5:2009 Editing and function section^[6]
ISO/IEC 9995-7:2009 Symbols used to represent functions^[7] with Amendment 1 (2012)^[8]
ISO/IEC 9995-8:2009 Allocation of letters to the keys of a numeric keypad^[9]
ISO/IEC 9995-9 (to be published) Multilingual-usage, multiscript keyboard group layouts^[10]
ISO/IEC 9995-10:2013 Conventional symbols and methods to represent graphic characters not uniquely recognizable by their glyph on keyboards and in documentation^[11]
ISO/IEC 9995-11:2015 Functionality of dead keys and repertoires of characters entered by dead keys^[12]

(ISO 9995-6:2006 Function section was withdrawn 2009-10-08.^[13])

ISO/IEC 9995-1

ISO/IEC 9995-1 provides a fundamental description of keyboards suitable for text and office systems, and defines several terms which are used throughout the ISO/IEC 9995 standard series.

Physical division and reference grid

The figure shows the division of a keyboard into sections, which are subdivided into zones.

alphanumeric section
- alphanumeric zone (indicated by green coloring)
- function zones (indicated by blue coloring)
numeric section
- numeric zone (indicated by darker red coloring)
- function zone (indicated by lighter red coloring)
editing and function section (in fact covering all parts of the keyboard which do not belong to the alphanumeric or numeric section)
- cursor key zone (indicated by darker grey coloring)
- editing function zone (indicated by lighter grey coloring)

The presence of a numeric section is not required by the standard. Also, the standard does not prevent a numeric section to be placed left of the alphanumeric section.

By means of the reference grid, each key can be identified by a unique combination of a letter (indicating the row) and a sequence of two digits (indicating the column). E.g., the key containing the digit one on several layouts is identified as “Key E01”. The labeling rules do allow for function keys to be arranged other than above of the alphanumeric section, or to be arranged in more than one row (thus, e.g. an AT keyboard is compliant to the standard):

Columns containing editing or function keys are to be numbered from 60 on when placed beyond a right numeric section, or from 80 downwards when placed left of the alphanumeric section.
Rows above of the alphanumeric section are to be labeled from K on, and rows below the space key are to be labeled from Z downwards.

The grid may be angled (as shown in the figure within the alphanumeric section), or squared (thus, keyboards where the alphanumeric keys are ordered in pure vertical columns are compliant to the standard).

The standard does not constrain the numbers of rows and columns in the alphanumeric section.

Levels and Groups

Levels (“unshifted” “shifted”, “AltGr”)

Key at grid position C12 on the German T2 layout which has 2 groups, each subdivided into up to 3 levels

Key at grid position E11 on the German T1 layout which has 3 levels in a single group

The characters which can be input by the keys in the alphanumeric section usually are organized in levels. For two-cased scripts like Latin, the basic level (“Level 1”) contains lower-case letters, while the “Level 2” contains capital letters (therefore, these levels are usually called “unshifted” and “shifted”). For characters which are not letters (like punctuation marks), no rules are given regarding their distribution among the levels. While digits are commonly in Level 1, there are exceptions (e.g. the French keyboard layout).

The standard allows for a third level (but not for more than three levels). Usually (but not mandatory by the standard), characters in such a level are selected by the means of an AltGr key.

Groups

If the organization into three levels is not sufficient to accommodate all characters to be contained in a specific layout, then “groups” may be defined which then constitute a higher hierarchical unit than levels. Thus, each such group usually is subdivided into (up to three) levels. Common examples are layouts allowing the input of characters of different scripts, like e.g. the Japanese keyboard layout (where the kana constitute the second group). Other examples are recent standardizations which allow the input of considerably more characters than their preceding editions (to overcome the historic limits of mechanical typewriters), like the Canadian Québec layout or the recently (2012) standardized German T2 layout.

Depictions on the keytops

According to ISO/IEC 9995-1, the level is indicated by the row where the character is depicted on the keytop:

Level 2 (“shifted”) above of Level 1 (“unshifted”)
Level 3 (“AltGr”) below Level 1 (“unshifted”).

The group is indicated by the column on the keytop:

The first or “primary group” at the left keytop border
The second or “secondary group” at the right keytop border
Additional groups (if existing) in between.

When letters on a case pair are associated with a key, only the capital character need to be shown on the keytop for the primary group, while the lowercase character only is shown for the secondary group.

Thus, on the depicted key of the German T2 layout, in the primary group are the characters “#” in Level 1 (unshifted), “'” in Level 2 (shifted), and “®” in Level 3 (accessed by the AltGr key). In the secondary group, there is the lowercase letter “ə” in Level 1 (unshifted) and its capital counterpart “Ə” in Level 2 (shifted).

For layouts containing only one group, characters in Level 3 may be depicted in the lower right corner of a keytop, to allow larger depictions for ergonomic reasons. For instance, on the depicted key of the German T1 layout, the “\” is in Level 3 (of the only defined group), to be accessed by the AltGr key.

Special issues

It is to be noted that on layouts like the US-International layout, the characters to be accessed by the AltGr key or the simultaneously pressed Shift and AltGr keys in fact constitute a second group containing Level 1 and Level 2, although the descriptions use to contain the terms “third level” and “fourth level”, erroneously in the terms of ISO/IEC 9995. In fact, on such layouts, the AltGr key is a “group selector” as defined in ISO/IEC 9995-2.

The selection of level and group during the input of a character (e.g. by means of a Shift key, an AltGr key, or a Group Selection key or key sequence) is specified in ISO/IEC 9995-2.

ISO/IEC 9995-2

ISO/IEC 9995-2 specifies requirements for the keys contained in the alphanumeric section (see the description of ISO/IEC 9995-1 above).

The alphanumeric zone (being a part of the alphanumeric section) has to contain 47 or more keys used to input characters, including the Space bar which has to be placed in the lowest row (row A according to the reference grid specified in ISO/IEC 9995-1). Also, there must be:

at least 12 keys in row E (the upmost row) in positions E00 to E15, containing all keys to input the decimal digits,
at least 12 keys in row D in positions D01 to D15,
at least 11 keys in row C in positions C01 to C15,
at least 10 keys in row B in positions B00 to B11.

The space bar has to expand at least over the positions A03 to A07. This implies that Japanese keyboards containing muhenkan, henkan, and the Katakana/Hiragana switch keys (the first one left, the other two right of the space bar) are not compliant to the standard if taken literally. This, however, is considered neglectable as the space bar has less importance in Japanese writing than in Latin or similar ones, as Japanese words usually are not separated by spaces.

Layouts which are designed for the Latin script must contain at least the 26 basic letters A…Z and a…z, the decimal digits 0…9, and the following characters contained in ISO 646: ! " % & ' * ( ) +, - . / : ; < = > ? _ and space.

Alphanumeric section of a keyboard, showing several details specified in ISO/IEC 9995-2

The keys shown grey in the figure, all being function keys, constitute the left and right function zones, while all other keys constitute the alphanumeric zone. The reference grid position of any function key may vary according to the specifications listed below. Especially, on a keyboard with considerably more than 47 keys in the alphanumeric zone, the right function keys will get higher column numbers.

The symbols shown for the function keys are specified in ISO/IEC 9995-7. Letterings which are commonly used instead of the symbols are shown in their English version in parentheses.

The harmonized 48 graphic key keyboard arrangement

Keyboards which comply to this narrower specification contain all the keys shown in white in the figure above, the key at C12 shown in yellow, and one of the two keys at E13 and B00 shown in red. The standard does not require this; it only says that keyboards complying to this narrower specification can be called such.

In fact, several layouts (e. g. the US layout), to allow a wider return key, have a key at D13 (shown in green) instead of C12 (shown in yellow). Thus, while they cannot be called “harmonized 48 graphic key keyboards” according to the standard, they still comply to the standard itself. It is to be noted that ISO/IEC 9995-3:2010, in referring to the basic layout within its specific scope, does take a possible substiitution of C12 by D13 into account.

Function keys

A tabulation key shall be present, occupying position D00 (i. e., the key may be wider, spanning over additional positions like D99 left of D00).

A key providing one of the functions Capitals lock (usually called “Caps Lock”), Level 2 lock (i. e. “Shift lock”), or Generalized lock shall be present, occupying the position C00. (The function “Generalized lock” is not specified in the ISO/IEC 9995 series). It is to be noted that the specific way the Caps Lock or Shift Lock works (i. e. swapping the lock state by hitting the key, as it is usually implemented) is not specified in the ISO/IEC 9995 series. Thus, solutions avoiding the status dependency as well as the problem of inadvertent hitting (e.g., the lock key pressed together with Shift turns Shift lock on, together with AltGr turns Caps Lock on, pressed alone switches off any lock status but has no effect when no lock status is activated) would not prevent compliance to the standard.

Return key on a German T1 keyboard, spanning over two rows

A Return key has to be present, right of the character input keys in row C. It is recommended that it expands to row D (thus spanning over position D13 when located on position C13 as shown in the figure), as it e. g. does on the German layout.

A key providing one of the functions Backspace or Backward erase shall be present in row A or (as it is more common) Row E, right of the character input keys.

If at least one Alternate key (commonly called “Alt key”) is present, it is to be positioned left of the space bar (or, if a function key specific to the writing system supported by the keyboard layout is there, left of that key).

If at least one Control key (commonly abbreviated “Ctrl”) is present, it has to be placed leftmost in row A (as it is more common), or row B.

If a Function key (commonly abbreviated “Fn”) is present, it is to be positioned left the space bar and left of an “Alternate” key, if such one is present. (It is allowed but explicitly not recommended to place the “Function” key left of the “Control” key.)

Level and Group selection

To select the Level 2 (commonly called “shifted”, see the subsection “Levels and Groups” of the section “ISO/IEC 9995-1” above), two keys shall be present in row B (commonly called Shift keys). The left one shall occupy position B99, while the right one shall be located right of the character input keys of that row. It is to be noted that the exact function of these keys (commonly pressing them together with the affected character input key) is not specified in the standard. Thus, solutions where the shift key is pressed, then released before the character input key is pressed, are compliant with the standard.

To select the Level 3 (if this is present on a layout), at least one Level 3 select key (frequently marked AltGr) shall be present. On keyboards compliant to the “harmonized 48 graphic key keyboard arrangement” (see above), such keys shall be placed in row A or row B. It is to be noted that, like for the shift keys, the exact function of these keys (commonly pressing them together with the affected character input key) is not specified in the standard.

For layouts containing more than one group, several mechanisms for group selection are specified. A dedicated Group selection key (marked by ⇨ according to ISO/IEC 9995-7), if present, shall be positioned adjacent to a “Level 3 select” (AltGr) key. For layouts containing a “Group 2” as specified in ISO/IEC 9995-3, this key shall work as a “latch” (i. e., when it is pressed and then released, the actuation of the next character input key causes the selection of a character of Group 2. After this, the status is reverted, thus subsequent character input key actuations refer to the basic group unless the “group selection” key is actuated again). If no dedicated “Group selection” key is present, its function is obtained by pressing the “Level 2 select” and “Level 3 select” (i. e. “Shift” and “AltGr”) key simultaneously and releasing them before actuating the selected character input key.

Allocation guidelines for layouts containing the Latin alphabet

An informative annex “Allocation guidelines” provides a basic pattern for arrangements of Latin letters, which in fact specifies a foundation for the kinds of keyboard layouts known as QWERTY, QWERTZ, or AZERTY. As this annex is not normative, it does not prevent other arrangements like the Dvorak keyboard or the Turkish F-keyboard being compliant to the ISO/IEC 9995 standard series.

The figure shows letters in black where a unique position is given, while the letters shown in red may alternatively occupy any of the positions where they are shown. Digits may be allocated on Level 0 (unshifted) or Level 1 (shifted). An asterisk indicates “any other character”.

ISO/IEC 9995-3

Common secondary group

ISO/IEC 9995-3:2010^[14] defines a common secondary layout (“common secondary group”) for the alphanumeric keyboard. These are engraved on the right part of the keytops; the standard defines their position independent of the characters of the primary layout. Thus, e. g. the Yen symbol “¥” occupies the shifted position on the 6th letter key of the second row, whether this is the Y key on an QWERTY keyboard (like the US layout) or the Z key on a QWERTZ keyboard (like the German layout).

ISO/IEC 9995-3:2010 applied to the US keyboard layout

Diacritical Marks and Peculiar Characters

The diacritical marks contained in the common secondary group act as dead keys, i.e. they are to be entered before the base characters they apply to. This mechanism is also to be used for sequences of more than one diacritical marks, to write languages like Vietmanese and Navajo.

Moreover, ISO/IEC 9995-3:2010 defines a list of “Peculiar Characters which can be entered as combinations using diacritical marks”. This list specifies combinations of a diacritical mark and a second key. E.g., symbols like the not-equal sign “≠” (Unicode U+2160) can be entered this way. Especially, letters with a horizontal stroke (like Croatian Đ/đ, Maltese Ħ/ħ, or Comanche Ʉ/ʉ) are entered this way using the "horizontal stroke accent" located on the K key.

Outdated common secondary group

The standard additionally defines an “outdated common secondary group” for compatibility purposes only. This resembles the “common secondary group” defined in the earlier edition of the standard, ISO/IEC 9995-3:2002.

The outdated ISO/IEC 9995-3:2002 applied to the US keyboard layout

Complementary Latin group layout

For cases where no national keyboard layout is available, or to be used as an additional group on layouts designed for other scripts than Latin, the standard specifies a “Complementary Latin group layout”. It is based on the “harmonized 48 graphic key keyboard arrangement” as defined in ISO/IEC 9995-2 (see description above). The assignment shown with red background shall occur once at one of the indicated positions.

The Complementary Latin group layout according to ISO/IEC 9995-3:2010

ISO/IEC 9995-4

Numeric section of a keyboard according to ISO/IEC 9995-4, showing several details specified in this standard

Numeric section of a real keyboard

ISO/IEC 9995-4 specifies the layout of the numeric section of a keyboard, if such one exists. It is subdivided into the function zone (shown with grey background in the left figure) and the numeric zone (shown with white background). The leftmost key in the lowest row may span to the left, occupying the position shown with yellow background.

The decimal digits 1…9 may be arranged in an “1-2-3 layout” (shown in green, named according to the keys in the D row), or in a ”7-8-9 layout” (shown in blue).

On a keyboard used for telematic functions, the symbols “” and “#” represent the initiator and the terminator. On a keyboard used for office purposes, the key denoted by “#” shall show the decimal separator (usually a dot or a comma, dependent on the user language). On such keyboards, the key position marked by the asterisk may be an extension of the “0” key, or a “double zero” key. Accordingly, if the yellow key position is used, it may be also an extension of the “0” key, a “double zero” key, or a “triple zero” key.

The keys in the function zone may be associated to the arithmetic function they denote, or to the arithmetic characters, dependent of the software which is used. If an additional tabulator key or another special key is used, it shall be located at the position C54 (according to the reference grid specified in ISO/IEC 9995-1), thus occupying the lower half of the place shown for the “=” key.

It is to be noted that numeric sections on usual keyboards for personal computers do not comply to the standard, as they usually have a Num lock key in the upper left corner where the standard requires the “+” key, and therefore also show a different arrangement of the other arithmetic keys (usually lacking an “=” key; see the second picture). By this, the standard in its present form (ISO/IEC 9995-4:2009) can be considered outdated. Full-size keyboards for Apple computers, however, do comply to these requirements.

ISO/IEC 9995-5

Cursor key arrangements

ISO/IEC 9995-5 specifies the layout of the editing and function section of a keyboard. In fact, it specifies only two items:

The Escape key has to be at the position K00 according to the reference grid specified in ISO/IEC 9995-1, or to the left of it (i. e., it has to be positioned near the left border of the first row above of the alphanumeric section).
The four cursor keys (up, down, left, and right) in the cursor key zone (as specified in ISO/IEC 9995-1) have to be arranged in a “cross layout” or an “inverted T layout” (see figure). The recommended placement is such that the “cursor down” key is placed on row A.

ISO/IEC 9995-7

Wikimedia Commons has media related to ISO 9995-7 symbols.

ISO/IEC 9995-7 specifies several symbols to be used on function keys. The figure shown above in the ISO/IEC 9995-2 section shows several examples. They are used extensively e. g. in the keyboard standard of the Province of Quebec, Canada.^[15]

ISO/IEC 9995-8

ISO/IEC 9995-8:2009 defines an assignment identical to E.161 of the 26 letters A–Z to the number keys of a numeric keypad. The space character is not assigned.

External links

Neuville (Y), Le clavier bureautique et informatique, Cedic/Nathan 1985 (origin of the ISO/IEC 9995 standard)
van Wingen, Johan (1999). "International Standards for Character Codes and Related Subjects". Retrieved 2006-12-17.
"Normalisation internationale des claviers : Documents du JTC1/SC35/GT1 au 1er mars 2001" (drafts of earlier editions of the parts of the ISO/IEC 9995 standard on Quebec.com)
"Norme Internationale ISO/CEI 9995-1 Première édition 1994-08-15" (draft of an earlier edition of ISO/IEC 9995-1)

References

This article is issued from Wikipedia - version of the Wednesday, January 27, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.