Joule thief

For the YouTube personality, see Alex Goyette.
A generic, conventional joule thief, shows parts and how they are wired together. The example uses a red LED. A ferrite toroid is wound to form a coil with primary (white) and feedback (green) windings. A 2N2222A transistor and 1000 ohm resistor are used.

A joule thief is a minimalist Armstrong[1] self-oscillating voltage booster that is small, low-cost, and easy to build, typically used for driving light loads.

It can use nearly all of the energy in a single-cell electric battery, even far below the voltage where other circuits consider the battery fully discharged (or "dead"); hence the name, which suggests the notion that the circuit is stealing energy or "joules" from the source. The term is a pun on the expression "jewel thief": one who steals jewelry or gemstones.

The circuit is a variant of the blocking oscillator that forms an unregulated voltage boost converter. The output voltage is increased at the expense of higher current draw on the input, but the integrated (average) current of the output is lowered and brightness of a luminescence decreased.

History

In the November 1999 issue of Everyday Practical Electronics (EPE) magazine, the "Ingenuity Unlimited" (reader ideas) section had a novel circuit idea entitled "One Volt LED - A Bright Light" by Z. Kaparnik from Swindon, Wilts, UK. Three example circuits were shown for operating LEDs from supply voltages below 1.5 Volts. The basic circuits consisted of a transformer-feedback ZTX450 NPN transistor voltage converter based on the blocking oscillator, which originally used a vacuum tube / thermionic valve and dates prior to World War II.[2]

The name "Joule Thief" was coined by Clive Mitchell[3][4] and given to his variant of Kaparnik's circuit which consisted of a single cell, a single BC549 NPN transistor, a coil with two windings, a single resistor (typically 1000 ohms), and a single white LED. Clive originally named the circuit "Vampire Torch", because it sucked the last remnants of life from a battery.

Mitchell's newer circuit is essentially the same as Kaparnik's older circuit, except for component values.

Description of operation

Example of a joule thief circuit driving an LED. The coil consists of a standard ferrite toroid core with two windings of 20 turns each using 0.15 mm (0.006 inch) diameter wire (38 swg) (34-35 AWG). The circuit can utilize an input voltage down to about 0.35 V and can run for weeks using a 1.5 V LR6/AA. The battery voltage is usually 1.5 V. The resistor is ~1 kΩ, 1/4 W. The transistor could be a 2N3904, BC547B, 2SC2500, BC337, 2N2222, 2N4401 or other NPN. Vceo = 30 V, P = 0.625 W. A white light-emitting diode with Vf = 3.2 V might be used.[3]
The waveform of an operating joule thief, showing a 30% duty cycle at approximately 40 kHz

The circuit works by rapidly switching the transistor. Initially, current begins to flow through the resistor, secondary winding and base-emitter junction (see diagram) which causes the transistor to begin conducting collector current through the primary winding. Since the two windings are connected in opposing directions, this induces a voltage in the secondary winding which is positive (due to the winding polarity, see dot convention) which turns the transistor on with higher bias. This self-stroking/positive-feedback process almost instantly turns the transistor on as hard as possible (putting it in the saturation region), making the collector-emitter path look like essentially a closed switch (since VCE will be only about 0.1 volts, assuming that the base current is high enough). With the primary winding effectively across the battery, the current increases at a rate proportional to the supply voltage divided by the inductance. Transistor switch-off takes place by different mechanisms dependent upon supply voltage.

At lower supply voltages a different mode of operation takes over: the gain of a transistor is not linear with VCE. At low supply voltages (typically 0.75 V and below) the transistor requires a larger base current to maintain saturation as the collector current increases. Hence, when it reaches a critical collector current, the base drive available becomes insufficient and the transistor starts to pinch off and the previously described positive feedback action occurs turning it hard off.

To summarize, once the current in the coils stops increasing for any reason, the transistor goes into the cutoff region (and opens the collector-emitter "switch"). The magnetic field collapses, inducing however much voltage is necessary to make the load conduct, or for the secondary-winding current to find some other path.

When the field is back to zero, the whole sequence repeats; with the battery ramping-up the primary-winding current until the transistor switches on.

If the load on the circuit is very small the rate of rise and ultimate voltage at the collector is limited only by stray capacitances, and may rise to more than 100 times the supply voltage. For this reason, it is imperative that a load is always connected so that the transistor is not damaged. Because VCE is mirrored back to the secondary, failure of the transistor due to a small load will occur through the reverse VBE limit for the transistor being exceeded (this occurs at a much lower value than VCEmax).

The transistor dissipates very little energy, even at high oscillating frequencies, because it spends most of its time in the fully on or fully off state, so either voltage over or current through the transistor is zero, thus minimizing the switching losses.

The switching frequency in the example circuit opposite is about 50 kHz. The light-emitting diode will blink at this rate, but the persistence of the human eye means that this will not be noticed.[3]

Regulated voltage

A closed-loop regulated joule thief

When a more constant output voltage is desired, the Joule Thief can be given a closed-loop control. In the example circuit, the Schottky diode D1 blocks the charge built up on capacitor C1 from flowing back to the switching transistor Q1 when it is turned on. A 5.6 Volt Zener diode D2 and transistor Q2 forms the feedback control: when the voltage across the capacitor C1 is higher than the threshold voltage formed by Zener voltage of D1 plus the base-emitter turn-on voltage of transistor Q2, transistor Q2 is turned on diverting the base current of the switching transistor Q1, impeding the oscillation and prevents the voltage across capacitor C1 from raising even further. When the voltage across C1 drops below the threshold voltage Q2 turns off, allowing the oscillation to happen again. If the load requires even lower ripple, in this example some delicate digital circuitry like a microcontroller, a linear regulator can be used after this to smooth the ripple out.

Prior art

In 1988, US Patent 4,734,658[5] describes a low voltage driven oscillator circuit, capable of operating from as little as 0.1 volts. This is a far lower voltage than that at which the joule thief will operate. This is achieved by using a JFET, which does not require the forward biasing of a PN junction for its operation, because it is used in the depletion mode. In other words, the drain–source already conducts, even when no bias voltage is applied. The '658 patent is intended for use with thermoelectric power sources, which are inherently low voltage devices.

See also

References

  1. ↑ "Fun Examples for Teaching Linear and Nonlinear Circuits", Circuits and Systems (ISCAS), 2013 IEEE International Symposium on, 19-23 May 2013, p2557 - 2560
  2. ↑ Everday Practical Electronics; November 1999.
  3. 1 2 3 "Make a joule thief", www.bigclive.com, retrieved 28 June 2013
  4. ↑ Clive's YouTube channel.
  5. ↑ google.com/patents: "Low Voltage Driven Oscillator Circuit", retrieved 20 March, 2012, filed 14 aug 1987

External links

Simulations and implementations
Video
Patents
Other
This article is issued from Wikipedia - version of the Friday, March 11, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.