KeyMod

KeyMod System

KeyMod Logo
Type Attachment System
Place of origin United States
Production history
Designer Eric Kincel
Designed 2011–2012
Manufacturer See Manufacturers
Produced 2012–present

KeyMod is a universal interface system for firearm accessory components designed to be supersede the MIL-STD-1913 accessory rails.[1] The concept was first created by VLTOR Weapon Systems of Tucson, Arizona, and released through Noveske Rifleworks of Grants Pass, Oregon, before being published in the public domain for adoption by the entire firearms accessory industry.[2][3][4] The name "KeyMod" was coined by Eric Kincel (then working for VLTOR Weapon Systems) following the naming trend of other VLTOR accessories with the suffix "Mod" meaning modular, and "Key" being a reference to the key-hole profile of the mounting slots.

Description

Direct attachment of a bipod using KeyMod system

KeyMod is an open-source design released for use and distribution in the public domain in an effort to standardize universal attachment systems in the firearm accessories market. The KeyMod system is intended to be used as a direct attachment method for firearm accessories such as flash light mounts, laser modules, sights, scope mounts, vertical grips, rail panels, hand stops, barricade supports, and many others.[5] The goal is to eliminate the need for the heavy and often non-ergonomic MIL-STD-1913 accessory rails. The KeyMod system consists of two parts: the KeyMod slot and the KeyMod nut. The slot is distinctive with a larger diameter through-hole combined with a narrow slot. The slot is chamfered on the backside while the through hole is sized for clearance of a quick-detach sling swivel (approximately 3/8" diameter).

The nut is stepped and the larger diameter end is chamfered around 270 degrees of its diameter. The angled face created is meant to interface with the chamfer on the backside of the KeyMod slot. The full diameter is left intact to create two flats on the nut which align the nut to the slot, and allow it to be indexed to the accessory as well as to the KeyMod slot. This eliminates the need to align the nuts to the holes prior to accessory installation as well as the need for tools to tighten the screw/nut. In most accessories, the screw is swaged after assembly to ensure that it cannot be backed out of the nut. This prevents loss of small parts (screws, nuts or other small parts used in the assembly of the accessory). The spacing of the holes is critical and is based on MIL-STD-1913 spacing to allow the greatest modularity with existing accessories.

The KeyMod specifications call out a "recoil lug" on the accessories which is intended to interface with the larger through hole portion and resist slippage of accessories during counter-recoil. The combination of the angled interface of the nut to the KeyMod slot and the recoil lug to the through hole make for a very strong attachment point which will not slip under harsh recoil or counter recoil. It also provides for an excellent return-to-zero when removed and re-installed.

History

VLTOR VIS KM series polylithic upper receiver using KeyMod interface.

VLTOR Weapon Systems had previously pursued a design which was the basis for the KeyMod system. While developing the first prototype systems Eric Kincel of VLTOR Weapon systems was approached by John Noveske of Noveske Rifleworks with a design for a universal accessory attachment system. After a short collaboration, during which Todd Krawczyk of Noveske Rifleworks suggested an improvement to the accessory lock/anti-rotation nut, John Noveske decided to adopt what became the KeyMod system for the NSR series of hand guards and accessories.[6] Kincel's design was developed simultaneously, but without knowledge of the independently developed keyhole slot system by Accuracy International, until after KeyMod's release.[7]

The specifications for the KeyMod system were first published in July 2012. The current revision was released in October 2012.

Technical specifications

The specifications for the KeyMod system were initially released by VLTOR Weapon Systems as an open-source set of drawings. As such, some manufacturers have added their own variations on the system such as using the through-hole portion as a sling-swivel attachment point. The critical interface dimensions, however, still follow the specifications. In an effort to ensure interface dimensions are kept consistent and repeatable, Bravo Company MFG released a set of drawings for KeyMod gauges that allow for expedient inspection of the 100° chamfer feature in January 2014.

See also

References

  1. ↑ Slowik, Max. "New Open-Source KeyMod Universal Mounting System by Vltor". Guns.com. Retrieved 3 August 2015.
  2. ↑ Curtis, Rob. "VLTOR gives the keymod tdp to you". Militarytimes.com. Retrieved 2013-04-09.
  3. ↑ Wiley, Suzanne. "Fad or the Future? The KeyMod Rail System". cheaperthandirt.com. Retrieved 2015-02-20.
  4. ↑ Fortier, David. "Mod Squad: Is KeyMod the New Industry Forend Standard?". http://www.rifleshootermag.com/. Retrieved 20 February 2015. External link in |website= (help)
  5. ↑ Muramatsu, Kevin (25 November 2014). Gun Digest Guide to Customizing Your AR-15. Gun Digest Books.
  6. ↑ Chin, Cass. "Noveske NSR Handguard". Military Morons. Retrieved 2013-04-09.
  7. ↑ (25 July 2012). "Introducing the Vltor KeyMod system." (Press release). Eric S. Kincel, Vltor Weapon Systems. Retrieved 23 January 2015.
This article is issued from Wikipedia - version of the Monday, February 01, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.