LOADALL
LOADALL is the common name for two different, undocumented machine instructions of Intel 80286 and Intel 80386 processors, which allow access to areas normally outside of the IA-32 API scope, like descriptor cache registers. The LOADALL for 286 processors is encoded 0Fh 05h, while the LOADALL for 386 processors is 0Fh 07h.[1]
Both variants – as the name implies – load all CPU internal registers in one operation. LOADALL had the unique ability to set up the visible part of the segment registers (selector) independently of their corresponding cached part, allowing the programmer to bring the CPU into states not otherwise allowed by the official programming model.
As an example of the usefulness of these techniques, LOADALL can set up the CPU to allow access to all memory from real mode, without having to switch it into protected mode (the so-called 'unreal mode'). Programs such as the RAMDRIVE and HIMEM drivers in MS-DOS, AboveDisk (a commercial package by Above Software which converted hard disk or extended memory into expanded memory), and OS/2 used LOADALL. Examination of the virtual machine monitor code in Windows/386 2.1 shows it uses both the 286 and the even less known 386 variant. Microsoft's HIMEM.SYS version 2.06[2] also used LOADALL to quickly copy to and from extended memory on 286 systems.
Another interesting usage of LOADALL, laid out in the book The Design of OS/2,[3] would have been to allow running former real mode programs in 16-bit protected mode, as utilized by Digital Research's Concurrent DOS 286 since 1985 [4] as well as FlexOS 286 and IBM 4680 OS since 1986/1987. Marking all the descriptor caches in the GDT and LDTs "not present" would allow the operating system to trap segment register reloads as well as attempts at performing real-mode specific "segment arithmetic" and emulate the desired behavior by updating the segment descriptors (LOADALL again). This "virtual 8086 mode" for the 80286 was, however, too slow to be practical. The idea had to be mostly discarded, furthermore, due to errata in some early Intel 80286 processors before the E-2 stepping.[4][5] As a result, OS/2 1.x – and Windows in "standard" mode as well – had to run DOS programs in real mode. Nevertheless, the idea was not lost; it led Intel to introduce the virtual mode of the 80386, allowing the implementation of "DOS boxes" at last in a relatively efficient and documented way.
Because LOADALL did not perform any checks on the validity of the data loaded into processor registers, it was possible to load a processor state which could not be normally entered, such as using real mode (PE=0) together with paging (PG=1) on 386 class CPUs.[6]
As the two LOADALL instructions were never documented, and do not exist on later processors, the opcodes were reused in the AMD64 architecture.[7] The opcode for the 286 LOADALL instruction, 0F05, became the AMD64 instruction SYSCALL; the 386 LOADALL instruction, 0F07, became the SYSRET instruction. These definitions were cemented even on Intel CPUs with the introduction of the Intel 64 implementation of AMD64.[8]
80286
Opcode 0F05. The instruction reads data from addresses 00800–00866, whatever the content of the segment registers.
| Address | number of bytes | register | register | register | register |
|---|---|---|---|---|---|
| 00800 | 6 | not used | |||
| 00806 | 2 | MSW (machine status word) | |||
| 00808 | 14 | not used | |||
| 00816 | 2 | TR (task register) | |||
| 00818 | 2 | flags | |||
| 0081A | 2 | IP (instruction pointer) | |||
| 0081C | 2 | LDTR (local descriptor table register) | |||
| 0081E | 4x2 | DS (data segment) | SS (stack segment) | CS (code segment) | ES (extra segment) |
| 00826 | 4x2 | DI (destination index) | SI (source index) | BP (base pointer) | SP (stack pointer) |
| 0082E | 4x2 | BX | DX | CX | AX |
| 00836 | 4x6 | ES segment descriptor | CS segment descriptor | SS segment descriptor | DS segment descriptor |
| 0084E | 4x6 | GDT, global descriptor table | LDT, local descriptor table | IDT, interrupt descriptor table | TSS, task state segment |
Note that the 80286 LOADALL instruction can not be used to switch from protected back to real mode[9] (it can't clear the PE bit in the MSW). However, use of the LOADALL instruction can avoid the need to switch to protected mode altogether.
80386
Opcode 0F07. The instruction loads data from address ES:EDI. It actually uses ES, not the ES descriptor.
| Address | number of bytes | register | register | register | register |
|---|---|---|---|---|---|
| ES:EDI+00 | 4 | CR0, control register 0 | |||
| ES:EDI+04 | 4 | EFLAGS | |||
| ES:EDI+08 | 4 | EIP, instruction pointer | |||
| ES:EDI+0C | 4x4 | EDI, destination index | ESI, source index | EBP, byte pointer | ESP, stack pointer |
| ES:EDI+1C | 4x4 | EBX | EDX | ECX | EAX |
| ES:EDI+2C | 2x4 | DR6 | DR7 | ||
| ES:EDI+34 | 4 | TR, task state selector | |||
| ES:EDI+38 | 4 | LDTR, local descriptor table | |||
| ES:EDI+3C | 4x2 | GS, extra segment | not used | FS, extra segment | not used |
| ES:EDI+44 | 4x2 | DS, data segment | not used | SS, stack segment | not used |
| ES:EDI+4C | 4x2 | CS, code segment | not used | ES, extra segment | not used |
| ES:EDI+54 | 4x12 | TSS descriptor, task state selector | IDT descriptor, interrupt descriptor table | GDT descriptor, global descriptor table | LDT descriptor, local descriptor table |
| ES:EDI+84 | 4x12 | GS segment descriptor | FS segment descriptor | DS segment descriptor | SS segment descriptor |
| ES:EDI+B4 | 2x12 | CS segment descriptor | ES segment descriptor |
See also
References
- ↑ Frank Van Gilluwe, The Undocumented PC, 1994, pages 62-70, ISBN 0-201-62277-7
- ↑ "Microsoft HIMEM.sys 2.06 source code".
- ↑ Deitel, H.M. (1992). The Design of OS/2. Addison-Wesley. ISBN 0-201-54889-5.
- 1 2 Edward Foster (13 May 1985). "Super DOS awaits new 80286 – Concurrent DOS 286 – delayed until Intel upgrades chip – offers Xenix's power and IBM PC compatibility". InfoWorld (InfoWorld Media Group) 7 (19): 17–18. ISSN 0199-6649.
- ↑ Edward Foster (26 August 1985). "Intel shows new 80286 chip – Future of DRI's Concurrent DOS 286 still unclear after processor fixed". InfoWorld (InfoWorld Media Group) 7 (34): 21. ISSN 0199-6649.
- ↑ Frank Van Gilluwe, The Undocumented PC, 1994, page 69, ISBN 0-201-62277-7
- ↑ "LOADALL Strikes Again". OS/2 Museum. 18 October 2013. Retrieved 27 January 2016.
- ↑ "Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 2B" (PDF). Intel Corporation. December 2015. Retrieved 27 January 2016.
- ↑ Slater, Michael (October 1987). "Secret 286 LOADALL instruction allows access to extended memory in real mode". Microprocessor Report.