Lever tumbler lock

Animation of a lever tumbler lock mechanism

A lever tumbler lock is a type of lock that uses a set of levers to prevent the bolt from moving in the lock. In the simplest of these, lifting the tumbler above a certain height will allow the bolt to slide past.

The number of levers may vary, but is usually an odd number for a lock that can be opened from each side of the door in order to provide symmetry. A minimum number of levers may be specified to provide an anticipated level of security (see 5 Lever locks section).

History

'Double acting' lever tumbler locks were invented in 1778 by Robert Barron of England.^[1]^[2] These required the lever to be lifted to a certain height by having a slot cut in the lever, so lifting the lever too far was as bad as not lifting the lever far enough. This type of lock is still currently used today, mostly on doors in the UK and some parts of Scandinavia, but can still be found on safes or gun cabinets. In modern times, these locks have declined in popularity because pin tumbler locks have become cheaper.

A 5 lever lock which is designed to be mortised into a door. The faceplate has been removed to see the inner workings.

Design

The lock is made up of levers (usually made out of non-ferrous metals). Each lever needs to be lifted to a specific height by the key in order for the locking bolt to move. Typically, the belly of the lever is cut away to various depths to provide different combinations, or the gate is cut in a different location, to provide differs. A lever will have pockets or gates through which the bolt stump moves during unlocking. Synonymous with "detainer".

Lever locks generally use a bitted key. Some locks used on safes use a double-bitted key, as do some door locks of a type often used in Southern and Eastern Europe.

3 lever locks

A 3 lever lock is a common type of lever lock, but is generally used for low security applications such as internal doors^[3] as their tolerances are much lower (there are fewer combinations of key available, so they are likely to unlock doors they shouldn't).

5 lever locks

A 5 lever lock is often required for home insurance and often recommended by the police for home security.^[4] There are various grades but the current British Standard (BS3621:2007) is usually required for insurance purposes. Valerie Olifent notes that "The doors of many historic churches still carry an old wooden lock although often you find that a modern 5-lever mortice lock has been installed alongside it to meet insurance requirements."^[5] BS3621:2007 requires a bolt throw of 20 mm rather than the 14 mm of the earlier British Standard.

Most BS3621 locks have anti pick devices built in to reduce the chance of lock picking, along with hardened bolts and anti-drill plates to reduce risk of physical attack.

Vulnerabilities

A type of lock pick used to pick lever tumbler locks

Lever tumbler locks can be picked with a tool called a curtain pick which is inserted into the keyway of the lock, and a force is applied to the locking bolt. The pick is then used to lift each lever inside the lock to the correct height so that the locking bolt can pass.

Higher security lever locks (such as the 5 lever) usually have notches cut into the levers - which catch the locking bolt and prevent it from moving if picking is attempted (similar to the security pins in a pin tumbler lock).

The Chubb Detector Lock is a variation of the lever lock which was designed to detect and prevent picking attempts by unauthorised persons without the correct key.

Lever locks can be drilled, but usually a template or stencil is required to mark the drilling point - as the lock mechanism is commonly mortised into the door and so it is harder to determine the point at which to drill.

References

Wikimedia Commons has media related to Lever tumbler locks.

↑ "The history of locks". London Locksmiths Ltd. Retrieved 8 November 2011.
↑ Bellis, Mary (8 November 2011). "The History of Locks". About.com Inventors. About.com. Retrieved 8 November 2011.
↑ "Lockshop Warehouse". 2 & 3 lever mortice locks are generally only recommended for use on internal doors as they do not provide adequate levels of security externally
↑ "Insurance company requirements | The Crime Prevention Website". thecrimepreventionwebsite.com. Retrieved 2016-03-13.
↑ "The Ancient Art of the Locksmith" http://www.buildingconservation.com/articles/locks/locks.htm

Locksmithing & Lock picking

Topics	Electric strike Key control Key relevance Lock bumping Lock picking Lockout-tagout Maison key system Rekeying Single-point locking Three-point locking

Components	Bitting Bolt stump Break Interchangeable core Key blank Key code Keyhole Lockset Shear line Split pin

Key types	Berlin key Bump key Change key Master key Skeleton key Smart key Tubular key Transponder key

Mechanical Locks	Bored cylindrical lock Bramah lock Cylinder lock Disc tumbler lock Key retainer Lever tumbler lock (Chubb detector lock) Magnetic-coded lock Magnetic keyed lock Mortise lock Padlock Combination lock Rotary combination lock Time-delay combination locks Pin tumbler lock (Snib) Protector lock Relocking device Time lock Tubular pin tumbler lock Warded lock Wafer tumbler lock

Electronic Locks	Electromagnetic lock Electronic lock Electric strike Magnetic-coded lock Keycard lock

Specific lock types	Bicycle lock Chamber lock Child safety lock Dead bolt Keycard lock Kensington Security Slot Luggage lock Power door locks The Club TSA lock

Tools	Lockpick Slim Jim Snap gun Tubular lock pick

Related	Bolt cutter Door chain Exit control lock Famous locksmiths Interlock (engineering) Keychain Key (engineering) Lock manufacturers Lock puzzle Lock snapping Locksport Two-man rule

Category:Locksmithing Keys Locks Book

This article is issued from Wikipedia - version of the Monday, May 02, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.