Timber roof truss

Two King post trusses linked to support a roof.
Key:1: ridge board, 2: purlins, 3: common rafters. This is an example of a "double roof" with principal rafters and common rafters.

A timber roof truss is a structural framework of timbers designed to bridge the space above a room and to provide support for a roof. Trusses usually occur at regular intervals, linked by longitudinal timbers such as purlins. The space between each truss is known as a bay.[1]

Timber roof trusses were a medieval development. Earlier roofs had been supported by coupled rafters – pairs of rafters linked by horizontal beams. But such roofs were structurally weak, and lacking any longitudinal support were prone to racking, a collapse resulting from horizontal movement.[2]

History

The top members of a truss are known generically as the top chord, bottom members as the bottom chord, and the interior members as webs. In historic carpentry the top chords are often called rafters, and the bottom chord is an often a tie beam. There are two main types of timber roof trusses: closed, in which the bottom chord is horizontal and at the foot of the truss, and open, in which the bottom chords are raised to provide more open space, also known as raised bottom chord trusses.[3]

Closed trusses

The terms closed truss and open truss are used in two ways to describe characteristics of truss roofs. Closed truss: 1) A truss with a tie beam; 2) a roof system with a ceiling so the framing is not visible. Open truss: 1) A truss with an interrupted tie beam or scissor truss which allow a vaulted ceiling area; 2) Roof framing open to view, not hidden by a ceiling.[4]

King post truss

King post truss.
Key: 1: King post, 2: tie beam, 3: principal rafters, 4: struts.

A king post truss has two principal rafters, a tie beam, and a central vertical king post.[5] The simplest of trusses, it is commonly used in conjunction with two angled struts.

The king post is normally under tension, and requires quite sophisticated joints with the tie beam and principal rafters. In a variation known as a king bolt (rod) truss the king post is replaced by a metal bolt (rod), usually of wrought iron.

Queen post truss

Queen post truss.
Key: 1: Queen posts, 2: tie beam, 3: straining beam, 4: principal rafters.

A queen post truss has two principal rafters and two vertical queen posts.[5] The queen post truss extends the span, and combined with spliced joints in the longer members extends the useful span for trusses of these types. As with a king post, the queen posts may be replaced with iron rods and thus called a queen rod truss. This truss is often known as a palladiana (Palladian truss) in Italy, as it was frequently used by the Venetian architect Andrea Palladio.[6][lower-alpha 1] Sometimes a palladian truss is defined as a compound truss with a queen post and king post truss in the same assembly.[7]

The queen post truss and the king post truss may be combined, by using the straining beam of the queen post truss as the tie beam for a king post truss above.[8] Such combinations are known as compound trusses.

Liegender Stuhl

German illustration of a purlin roof with liegendem stuhl truss highlighted in blue.

Liegender stuhl is a truss of German origin, the German name is used in America. This truss is found in some 18th and 19th-century buildings where Germans settled in the U.S. The literal translation is "lying chair", lying meaning the top chords are angled or leaning and chair in the sense of a support, in this case a post or truss.[9] Carpenters in the Netherlands also used this truss where it is spelled liggende stoel.[10]

Open trusses

Arch-braced truss

A single arch-braced truss.
Key: 1: principal rafters, 2: collar beam, 3: arch braces.

Lacking a tie beam,[11] the arch-braced (arched brace)[12] truss gives a more open look to the interior of the roof. The principal rafters are linked by a collar beam supported by a pair of arch braces, which stiffen the structure and help to transmit the weight of the roof down through the principal rafters to the supporting wall. A double arch braced truss[12] has a second pair of arched braces lower down, from the rafter to a block or inner sill: This form is called a wagon, cradle, barrel or tunnel roof because of this cylindrical appearance.[13]

Hammerbeam truss

Chambers 1908 single hammerbeam truss

The hammerbeam roof was the culmination of the development of the arch-braced truss, allowing greater spaces to be spanned. The hammerbeam roof of Westminster Hall in London, designed by Hugh Herland and installed between 1395 and 1399, was the largest timber-roofed space in medieval Europe, spanning a distance of just over 20 metres (66 ft).[14] It is considered to be the best example of a hammer-beam truss in England.[15]

Hammer beam trusses can have a single hammerbeam or multiple hammerbeams. A false hammerbeam roof (truss) has two definitions: 1) There is no hammer post on the hammer beam[16][17] as sometimes found in a type of arch brace truss[18] or; 2)The hammer beam joins into the hammer post instead of the hammer post landing on the hammer beam.[19]

Scissor truss

A scissor truss

The scissor truss gets its name from being shaped like a pair of shears (scissors). Two defining features of a scissor truss are: 1) the joint where the bottom chords pass (the hinge of a pair of scissors) must be firmly connected and 2) the rafter (top chord) feet must land on the bottom chords. If the bottom chords join to the under-side of the top chords the assembly is said to be "scissor braced"[20] rather than a scissor truss.

See also

References

Notes

  1. The palladiana had been used in Italy for many years before Palladio's time, but has been given his name because of its extensive use in the buildings he designed.[6]

Citations

  1. Curl, James Stevens (2006), "truss", A Dictionary of Architecture and Landscape Architecture (online ed.), Oxford University Press, retrieved 1 December 2012 (subscription required)
  2. Steane (1984), p. 196
  3. Lewandoski, Jan, Jack Sobon, and Kenneth Rower. Historic American roof trusses. Becket, MA: Timber Framers Guild, 2006. 48. ISBN 0970664346
  4. Domestic Buildings Research Group (Surrey, England), http://www.dbrg.org.uk/GLOSSARY/Open%20truss.html
  5. 1 2 Glossary of Australian Building Terms – Third Edition.(NCRB)
  6. 1 2 Valeriani, Simona (August 2006), "The Roofs of Wren and Jones: A Seventeenth-Century Migration of Technical Knowledge from Italy to England". Working Papers on the Nature of Evidence: How Well Do 'Facts' Travel?", (PDF), Department of Economic History, London School of Economics http://eprints.lse.ac.uk/22534/1/1406Valeriani.pdf, retrieved 22 December 2012 Missing or empty |title= (help)
  7. Proceedings of the Third Annual Congress on Construction History, May 2009. Figure 1. based on Sachero, C., 1864: Sulla stabilità delle armature dei tetti. Giornale del Genio Militare 2. 250. http://www.bma.arch.unige.it/PDF/CONSTRUCTION_HISTORY_2009/VOL3/TURRI-Zamperin_Cappelletti_1_paper-revised_layouted.pdf accessed 12/24/2012
  8. Yeomans (2003), p. 42
  9. Anderegg, Jean. Holzbaukunst: Fachwerk, Dachgerüst, Zimmermannswerkzeug : systematisches Fachwörterbuch = Architecture en bois : construction en pan de bois, charpente de toit, outils du charpentier : dictionnaire spécialisé et systématique = Architecture in wood : timber-frame construction, roof frame, carpenter's tools : specialized and systematic dictionary. Munich: K.G. Saur, 1997. : 65. ISBN 3598104618
  10. Herman Janse, Houten kappen in Nederland 1000-1940. Delftse Universitaire Pers, Delft / Rijksdienst voor de Monumentenzorg, Zeist 1989.
  11. Harris (2003), pp. 75–77
  12. 1 2 Chappell, Steve. A timber framer's workshop: joinery, design & construction of traditional timber frames. Brownfield, Me.: Fox Maple Press, 1998. 115. Print.
  13. Whewell, William, and F. de. Lassaulx. Architectural notes on German churches; with notes written during an architectural tour in Picardy and Normandy.. The 3d ed. Cambridge: J. and J.J. Deighton; [etc.], 1842. 44. Print.
  14. Steane (1984), pp. 196–97
  15. Webber, Frederick G.. Carpentry & Joinery. Methuen and Co., London: 1898. 152.
  16. Davies, Nikolas, and Erkki Jokiniemi. Dictionary of architecture and building construction. Amsterdam: Elsevier/Architectural Press, 2008. 144.
  17. Alcock, N. W.. Recording timber-framed buildings: an illustrated glossary. London: Council for British Archaeology, 1989.
  18. Sharpe, Geoffrey R.. Historic English churches a guide to their construction, design and features. London: I.B. Tauris, 2011. 111. fig. 61.
  19. Wood, Margaret. The English Mediaeval House. London: Ferndale Editions, 1980, 1965. 319.
  20. Lewandoski, Jan, Jack Sobon, and Kenneth Rower. Historic American roof trusses. Becket, MA: Timber Framers Guild, 2006. 7. ISBN 0970664346

Bibliography

External links


This article is issued from Wikipedia - version of the Sunday, September 13, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.