Rolls-Royce/SNECMA M45H

M45H
M45H engine on display at the Royal Air Force Museum Cosford
Type Turbofan
Manufacturer Rolls-Royce/SNECMA
First run 1970
Major applications VFW-Fokker 614



The Rolls-Royce/SNECMA M45H was a medium bypass ratio turbofan produced specifically for the twin-engined VFW-Fokker 614 aircraft in the early 1970s.

The design was started as a collaborative effort between Bristol Siddeley and SNECMA.[1]

Design and development

The VFW 614 was designed to operate over short sectors with up to a dozen flights a day. The engines were optimized for 30 minute sectors at a cruise altitude of 21,000 feet at Mach 0.65. Only a few minutes would be spent at the cruise rating and most of the flight would be at the higher climb rating or at a descent setting. The engine had a low turbine entry temperature and comparatively low rotational speed.[2]

The engine was designed to be uprated without drastic redesign. Three options were water injection (+10 thrust), improved HP turbine (+10% thrust), addition of a zero-stage to the LP compressor (+25% thrust).[2]

The engine was developed at the time of the Rolls-Royce bankruptcy which resulted in delays in developing the engine.[3]

Variants

The M45SD-02 or RB.410 was a derivative of the M45H-01 turbofan, designed to demonstrate ultra-quiet engine technologies, needed for STOL aircraft operating from city centre airports.

A geared, variable pitch fan, replaced the first stage of the low pressure (LP) compressor. A modest fan pressure ratio, consistent with the high bypass ratio, meant a low fan tip speed could be employed. A low hot jet velocity was another major design feature.

In reverse thrust, intake air entered the bypass duct, via a gap in the cold nozzle outer wall, and went through the fan, to be expelled through the intake. A small proportion of the bypass duct air entered the IP compressor, via a special diverter valve, to sustain the gas generator. Reverse thrust was obtained by the fan going through fine (rather than feather) pitch. Engine testing took place in the mid 1970s.

The Chief Engineer of this project was David McMurtry, co-founder and Chairman of Renishaw PLC. After the prototype engine was stored, it was given to Sir David for safe keeping at the New Mills site.

The M45SD-02 variable geometry fan engine at the New Mills Technology Centre.

Engines on display

A Rolls-Royce/SNECMA M45H engine is on display as part of the aero engine collection at the Royal Air Force Museum Cosford.

Specifications (M45H Mk.501)

An M45H in its overwing mount on the VFW-Fokker 614 at the Aeronauticum museum

Data from Jane's All the World's Aircraft 1971-72.[4]

General characteristics

Components

Performance

Specifications (M45SD-02)

Data from Flight International 1973 [7]

General characteristics

Components

Performance

See also


Comparable engines
Related lists

References

Notes
  1. ↑ Flight 6 January 1966
  2. 1 2 https://www.flightglobal.com/pdfarchive/view/1974/1974%20-%200622.html
  3. ↑ Swanborough 1971, p.371.
  4. ↑ J W R Taylor 1971,p.650.
  5. ↑ http://www.flightglobal.com/FlightPDFArchive/1971/1971%20-%202336.PDF
  6. ↑ http://www.caa.co.uk/docs/702/1RR001_01102004.pdf
  7. ↑ D. G. M. Davis (19 April 1973), "Progress in Britain" (pdf), Flight International: 615
Bibliography
  • Swanborough, Gordon. Air Enthusiast, Volume One. London: Pilot Press, 1971. ISBN 0-385-08171-5.

External links

Wikimedia Commons has media related to Rolls-Royce/SNECMA M45H.
This article is issued from Wikipedia - version of the Friday, February 26, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.