Materials for use in vacuum

Materials for use in vacuum are materials showing very low rate of outgassing in vacuum, and, where applicable, tolerant to the bake-out temperatures. The requirements grow increasingly stringent with the desired degree of vacuum achievable in the vacuum chamber. The materials can produce gas by several mechanisms. Molecules of gases and water can be adsorbed on the material surface (therefore materials with low affinity to water have to be chosen, which eliminates many plastics). Materials may sublimate in vacuum (this excludes some metals and their alloys, most notably cadmium and zinc). Or the gases can be released from porous materials or from cracks and crevices. Traces of lubricants, residues from machining, can be present on the surfaces. A specific risk is outgassing of solvents absorbed in plastics after cleaning.

The gases liberated from the materials not only lower the vacuum quality, but also can be reabsorbed on other surfaces, creating deposits and contaminating the chamber.

Yet another problem is diffusion of gases through the materials themselves. Atmospheric helium can diffuse even through Pyrex glass, even if slowly; this however is usually not an issue. Some materials might also expand or increase in size causing problems in delicate equipment.

In addition to the gas-related issues, the materials have to maintain adequate strength through the entire required temperature range (sometimes reaching cryogenic temperatures), maintain their properties (elasticity, plasticity, electrical and thermal conductivity or lack of it, etc.), be possible to machine, and if possible not being overly expensive. Yet another concern is the thermal expansion coefficient match of adjacent parts.

Materials to avoid

Materials outgas by three mechanisms: release of absorbed gases, release of adsorbed gases, and evaporation of the material itself. The former can be reduced by a bakeout, the latter is an intrinsic property of the material.[1] Some outgassed materials can deposit on other surfaces, contaminate the vacuum system and be difficult to get rid of.

The most common sources of trouble (out-gassing) in vacuum systems are:

Materials for vacuum use

Metals

Plastics

Glasses and ceramics

Lubricants

Lubrication of moving parts is a problem for vacuum. Many lubricants have unacceptable outgassing rates,[3] others (e.g. graphite) lose lubricating properties.

Adhesives

Materials for use in space

In addition to the concerns above, materials for use in spacecraft applications have to cope with radiation damage and high-intensity ultraviolet radiation, thermal loads from solar radiation, radiation cooling of the vehicle in other directions, and heat produced within the spacecraft's systems. Another concern, for orbits closer to Earth, is the presence of atomic oxygen, leading to corrosion of exposed surfaces; aluminium is an especially sensitive material. Silver, often used for surface-deposited interconnects, forms layer of silver oxide that flakes off and may erode up to a total failure.

Corrosion-sensitive surfaces can be protected by a suitable plating, most often with gold; a silica layer is also possible. However the coating layer is subject to erosion by micrometeoroids.

References

  1. 1 2 3 4 Meurant, G. (1980). Vacuum Physics and Technology. Elsevier Science. p. 346. ISBN 9780080859958. Retrieved 2015-09-08.
  2. 1 2 3 4 5 6 7 8 G. Lee (August 15, 1989). "TM-1615: Materials for Ultra-High Vacuum" (PDF). Fermi National Accelerator Laboratory. Retrieved 2015-09-08.
  3. Carré, D. J.; Bertrand, P. A. (1999). "Analysis of Hubble Space Telescope Reaction Wheel Lubricant". Journal of Spacecraft and Rockets 36 (1): 109–113. doi:10.2514/2.3422.
  4. "TorrLube.com | The Unrivaled Leader in High Vacuum Lubrication". torrlube.com. Retrieved 2015-09-08.
  5. Ketan (2 December 2008). "Comparision between Molybdenum Disulfide & Tungsten Disulfide" (PDF). Retrieved 2015-09-08.
  6. "Applied Tungstenite: Aerospace: Tungsten Disulfide WS2 dry film Lubricant and Citric Acid Passivation". appliedtungstenite.com. Retrieved 2015-09-08.
This article is issued from Wikipedia - version of the Monday, April 11, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.