Message Transfer Part

SS7 protocol suite
SS7 protocols by OSI layer
Application	INAP, MAP, IS-41... TCAP, CAP, ISUP, ...
Network	MTP Level 3 + SCCP
Data link	MTP Level 2
Physical	MTP Level 1

The Message Transfer Part (MTP) is part of the Signaling System 7 (SS7) used for communication in Public Switched Telephone Networks. MTP is responsible for reliable, unduplicated and in-sequence transport of SS7 messages between communication partners.

MTP is formally defined primarily in ITU-T recommendations Q.701, Q.702, Q.703, Q.704 and Q.705. Tests for the MTP are specified in the ITU-T recommendations Q.781 for MTP2 and in Q.782 for MTP3. These tests are used to validate the correct implementation of the MTP protocol.

Different countries use different variants of the MTP protocols. In North America, the formal standard followed is ANSI T1.111. In Europe, national MTP protocols are based on ETSI EN 300-008-1.

Functional levels

The SS7 stack can be separated into four functional levels:^[1] Level 1 through Level 3 comprise the MTP, and Level 4 the MTP user. MTP Level 3 is sometimes abbreviated MTP3; MTP Level 2, MTP2.^[2] MTP and SCCP are together referred to as the Network Service Part (NSP).^[3]

There is no one-to-one mapping of MTP Levels 1 through 3 onto the OSI model.^[4] Instead, MTP provides the functionality of layers 1, 2 and part of layer 3 in the OSI model.^[5] The part of layer 3 of the OSI model that MTP does not provide, is provided by SCCP or other Level 4 parts (MTP users).^[6]^[7]

Signalling Data Link Functional Level

MTP Level 1 is described in ITU-T Recommendation Q.702, and provides the Signalling Data Link functional level for narrowband signalling links. For broadband signalling links, ITU-T Recommendation Q.2110 or Q.2111 describe the signalling data link function.

MTP1 represents the physical layer. That is, the layer that is responsible for the connection of SS7 Signaling Points into the transmission network over which they communicate with each other. Primarily, this involves the conversion of messaging into electrical signal and the maintenance of the physical links through which these pass. In this way, it is analogous to the Layer 1 of ISDN or other, perhaps more familiar, protocols.

MTP1 normally uses a timeslot in an E-carrier or T-carrier. The Physical interfaces defined include E-1 (2048 kbit/s; 32 64 kbit/s channels), DS-1 (1544 kbit/s; 24 64kbit/s channels), V.35 (64 kbit/s), DS-0 (64 kbit/s), and DS-0A (56 kbit/s).

Signalling Link Functional Level

MTP Level 2 is described in ITU-T Recommendation Q.703, and provides the Signalling Link functional level for narrowband signalling links. For broadband signalling links, ITU-T Recommendation Q.2140 and Q.2210 describe the signalling link function referred to as MTP3b. The signalling link functional level may also be provided using the SIGTRAN protocol M2PA described in RFC 4165.

MTP Level 2 ensures accurate end-to-end transmission of a message across a signaling link.

MTP2 provides flow control, error detection and sequence checking, and retransmits unacknowledged messages. MTP2 uses packets called signal units to transmit SS7 messages. There are three types of signal units: Fill-in Signal Unit (FISU), Link Status Signal Unit (LSSU), Message Signal Unit (MSU).

Access to the signalling link functional level's service interface can be provided over SCTP by the SIGTRAN protocol M3UA, described in RFC 3331.

MTP Level 2 is tested using the protocol tester and test specifications described in Q.755, Q.755.1, Q.780 and Q.781.

Signalling Network Functional Level

MTP Level 3 is described in ITU-T Recommendation Q.704, and provides the Signalling Network functional level for narrowband signalling links and, with only minor modifications described in ITU-T Recommendation Q.2210, for broadband signalling links. The functions of MTP Level 3 may also be replaced with the Generic Signalling Transport Service described in ITU-T Recommendation Q.2150.0 as provided by MTP3b (Q.2150.1), SSCOP or SSCOPMCE (Q.2150.2) or SCTP (Q.2150.3). MTP Level 3 functions can also be provided by using the IETF SIGTRAN M3UA protocol, described in RFC 4666, in IPSP mode.

MTP3 provides routing functionality to transport signaling messages through the SS7 network to the requested endpoint. Each network element in the SS7 network has a unique address, the Point Code (PC). Message routing is performed according to this address. A distinction is made between a Signaling Transfer Point (STP) which only performs MTP message routing functionalities and a Signaling End Point (SEP) which uses MTP to communicate with other SEPs (that is, telecom switches). MTP3 is also responsible for network management; when the availability of MTP2 data links changes. MTP3 establishes alternative links and re-routes traffic away from failed links and signaling points and propagates information about route availability through the network. Also controls traffic when congestion occurs.

Access to the signalling network functional level's service interface (as described in Q.701) can be provided over SCTP by the SIGTRAN protocol M3UA, described in RFC 4666.

MTP Level 3 is tested using the protocol tester and test specifications described in Q.755, Q.755.1, Q.780 and Q.782.

MTP Users

Level 4 consists of MTP Users. The remaining components of the SS7 stack are all directly, or indirectly, MTP Users. Some examples of parts at Level 4 are SCCP, ISUP, TUP, and, in the UK, IUP.^[7] The services provided to MTP Level 4 by the MTP (that is, MTP to MTP Users) is described in ITU-T Recommendation Q.701.

References

↑ ITU-T Recommendation Q.700, Figure 3/Q.700, SS No. 7 functional levels, p. 8.
↑ See for example, RFC 3331 and RFC 3332 for the usage MTP2 and MTP3.
↑ ITU-T Recommendation Q.711 (03/2001), Figure 1/Q.711, Functional diagram for the SCCP in Signalling System No. 7, p. 2.
↑ ITU-T Recommendation Q.700 (03/1993), Clause 4, OSI layering and SS No. 7, p. 9.
↑ ITU-T Recommendation Q.700 (03/1993), Figure 2/Q.700, Architecture of SS No. 7, p. 7.
↑ ITU-T Recommendation Q.1400 (03/1993), Clause 2.2, OSI layering and SS No. 7", p. 4.
1 2 ITU-T Recommendation Q.1400 (03/1993), Figure 1/Q.1400, Relationship between SS No. 7 Functional Levels and OSI Layering, p. 5.

ITU-T recommendations

ITU-T Recommendation Q.700, Introduction to CCITT Signalling System No. 7.
ITU-T Recommendation Q.701, Functional description of the message transfer part (MTP) of Signalling System No. 7.
ITU-T Recommendation Q.702, Signalling data link.
ITU-T Recommendation Q.703, Signalling link.
ITU-T Recommendation Q.704, Signalling network functions and messages.
ITU-T Recommendation Q.705, Signalling network structure.
ITU-T Recommendation Q.706, Message transfer part signalling performance.
ITU-T Recommendation Q.707, Testing and maintenance.
ITU-T Recommendation Q.708, Assignment procedures for international signalling point codes.
ITU-T Recommendation Q.709, Hypothetical signalling reference connection.
ITU-T Recommendation Q.710, Simplified MTP version for small systems.
ITU-T Recommendation Q.750, Overview of Signalling System No. 7 management.
ITU-T Recommendation Q.751.1, Network element management information model for the Message Transfer Part (MTP).
ITU-T Recommendation Q.751.3, Network element information model for MTP accounting.
ITU-T Recommendation Q.752, Monitoring and measurements for Signalling System No. 7 networks.
ITU-T Recommendation Q.755, Signalling System No. 7 protocol tests.
ITU-T Recommendation Q.755.1, MTP Protocol Tester.
ITU-T Recommendation Q.780, Signalling System No. 7 test specification — General description.
ITU-T Recommendation Q.781, MTP Level 2 test specification.
ITU-T Recommendation Q.782, MTP Level 3 test specification.
ITU-T Recommendation Q.1400, Architecture framework for the development of signalling and OA&M protocols using OSI concepts.
ITU-T Recommendation Q.2110, B-ISDN ATM adaptation layer — Service specific connection oriented protocol (SSCOP).
ITU-T Recommendation Q.2111, B-ISDN ATM adaptation layer — Service specific connection oriented protocol in a multilink and connectionless environment (SSCOPMCE).
ITU-T Recommendation Q.2140, B-ISDN ATM adaptation layer — Service specific coordination function for signalling at the network node interface (SSCF at NNI).
ITU-T Recommendation Q.2150.0, Generic signalling transport service.
ITU-T Recommendation Q.2150.1, Signalling transport converter on MTP3 and MTP3b.
ITU-T Recommendation Q.2150.2, Signalling transport converter on SSCOP and SSCOPMCE.
ITU-T Recommendation Q.2150.3, Signalling transport converter on SCTP.
ITU-T Recommendation Q.2210, Message transfer part level 3 functions and messages using the services of ITU-T Recommendation Q.2140.

IETF RFCs

RFC 2719, Framework Architecture for Signaling Transport.
RFC 4165, Signaling System 7 (SS7) Message Transfer Part 2 (MTP2) — User Peer-to-Peer Adaptation Layer (M2PA).
RFC 3331, Signaling System 7 (SS7) Message Transfer Part 2 (MTP2) — User Adaptation Layer (M2UA)
RFC 4666, Signaling System 7 (SS7) Message Transfer Part 3 (MTP3) — User Adaptation Layer (M3UA)

External links

- SS7 Tutorial.

This article is issued from Wikipedia - version of the Thursday, March 05, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.