Minimum energy performance standard

A MEPS (Minimum Energy Performance Standard) is a specification, containing a number of performance requirements for an energy-using device, that effectively limits the maximum amount of energy that may be consumed by a product in performing a specified task.

A MEPS is usually made mandatory by a government energy efficiency body. It may include requirements not directly related to energy; this is to ensure that general performance and user satisfaction are not adversely affected by increasing energy efficiency.

A MEPS generally requires use of a particular test procedure that specifies how performance is measured.

In North America when addressing energy efficiency, a MEPS is sometimes referred to simply as a “standard”, as in “Co-operation on Labeling and Standards Programs”. In Latin America when addressing energy efficiency, MEPS are sometimes referred to as Normas (translated as "norms").

Examples

Price, volume and efficiency of refrigerators

A storage water heater providing hot water for sanitary purposes is required to heat up a specified quantity of water to a specified temperature and store it at that temperature for a specified time while consuming a limited amount of energy. In this example, the requirements for heating up and for maintaining the temperature may be applied as two separate energy performance requirements or there may be a single task efficiency.

A compact fluorescent lamp is required to start and run up to near full brightness in a given time, to have a minimum life of several thousand hours, to maintain its output within specified limits, to withstand a certain number of switchings, to have a consistent colour appearance and a specified colour rendering. Its energy performance requirement is usually stated in terms of minimum efficacy (light output per electrical input).

California

In the U.S., the state of California was a pioneer [1] in the introduction of MEPS. In order to reduce the growth in electricity use, the California Energy Commission (CEC) was given unique and strong authority to regulate the efficiency of appliances sold in the state. It started to adopt appliance efficiency regulations in 1978, and has updated the standards regularly over time, and expanded the list of covered appliances.

In 1988, California's standards became national standards for the U.S. through the enactment of the National Appliance Energy Conservation Act (NAECA). The federal standards preempted state standards (unless the state justified a waiver from federal preemption based on conditions in the state), and since then, the U.S. Department of Energy has had the responsibility to update the federal standards.

California has continued to expand the list of appliances it regulates for appliances that are not federally regulated, and therefore not preempted. In recent years, the CEC's attention has been focused on consumer electronics, for which energy use has been growing dramatically.

Australia

MEPS programs are made mandatory in Australia by state government legislation and regulations which give force to the relevant Australian Standards. It is mandatory for the following products manufactured in or imported into Australia to meet the MEPS levels specified by the relevant Australian Standards:

Calendar of implementation of MEPS in Australia[2]
Appliance Date
Refrigerators and freezers 1 October 1999
Mains pressure electric storage water heaters 1 October 1999
Three phase electric motors 1 October 2001
Three-phase air conditioners 1 October 2001
Ballasts for linear fluorescent lamps 1 March 2003
Single-phase air conditioners 1 October 2004
Linear fluorescent lamps 1 October 2004
Distribution transformers 1 October 2004
commercial refrigeration 1 October 2004
Pressure electric storage water heaters smaller than 80 liters,
low pressure and heat exchange types		 1 October 2005

Brazil

A law was approved in 2001.[3] MEPS have been set for three-phase electric motors and compact fluorescent lamps.

New Zealand

On 5 February 2002, New Zealand introduced Minimum Energy Performance Standards (MEPS) with Energy Efficiency Regulations. MEPS and energy rating labels help improve the energy efficiency of our products, and enable consumers to choose products that use less energy. Products covered by MEPS must meet or exceed set levels for energy performance before they can be sold to consumers. MEPS have been updated over the years (2002, 2003, 2004, 2008, 2011) to cover a wide range of products, and increasing levels of stringency. New Zealand works with Australia to harmonise MEPS levels. Almost all of its standards are joint standards with Australia. New Zealand has mandatory Energy rating labelling for dishwashers and clothes dryers, fridges, washing machines and room air conditioners. MEPS apply to the following:[4]

See also

References

  1. ↑ http://www.eceee.org S. Nadel S., 2003, Appliance & equipment efficiency standards in the US: Accomplishments,next steps and lessons learned, ECEEE 2003 Summer Study, St Raphael.
  2. ↑ energy jargon
  3. ↑ Energy Efficiency in Brazil. Paulo Augusto Leonelli, Brazilian Ministry of Mines and energy. November 20, 2007
  4. ↑ Energy Efficiency and Conservation Authority of New Zealand http://www.eeca.govt.nz/standards-and-ratings/minimum-energy-performance-standards-and-labelling

External links

This article is issued from Wikipedia - version of the Saturday, April 23, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.