Molten salt reactor

Molten salt reactor scheme

A molten salt reactor (MSR) is a class of generation IV nuclear fission reactor in which the primary nuclear reactor coolant, or even the fuel itself, is a molten salt mixture. MSRs run at higher temperatures than water-cooled reactors for higher thermodynamic efficiency, while staying at low vapor pressure.[1]

The nuclear fuel may be solid or dissolved in the coolant itself. In many designs the nuclear fuel is dissolved in the molten fluoride salt coolant as uranium tetrafluoride (UF4). The fluid becomes critical in a graphite core which serves as the moderator. Solid fuel designs rely on ceramic fuel dispersed in a graphite matrix, with the molten salt providing low pressure, high temperature cooling. The salts are much more efficient than compressed helium at removing heat from the core, reducing the need for pumping and piping and reducing the size of the core.

Although the concept is not new (it has been around since the 1950s) there has been a renewed interest in the technology along with other Generation IV reactor technologies.[2] The early Aircraft Reactor Experiment (1954) was primarily motivated by the small size that the design could provide, while the Molten-Salt Reactor Experiment (1965–1969) was a prototype for a thorium fuel cycle breeder reactor nuclear power plant. One of the Generation IV reactor designs is a molten-salt-cooled, molten-salt-fuelled reactor; the initial reference design is 1000 MWe.[3]

History

Aircraft reactor experiment

Aircraft Reactor Experiment building at ORNL. It was later retrofitted for the MSRE.

Extensive research into molten salt reactors started with the U.S. aircraft reactor experiment (ARE) in support of the U.S. Aircraft Nuclear Propulsion program. The ARE was a 2.5 MWth nuclear reactor experiment designed to attain a high power density for use as an engine in a nuclear-powered bomber. The project included several reactor experiments including high temperature reactor and engine tests collectively called the Heat Transfer Reactor Experiments: HTRE-1, HTRE-2 and HTRE-3 at the National Reactor Test Station (now Idaho National Laboratory) as well as an experimental high-temperature molten salt reactor at Oak Ridge National Laboratory – the ARE. The ARE used molten fluoride salt NaF-ZrF4-UF4 (53-41-6 mol%) as fuel, was moderated by beryllium oxide (BeO), used liquid sodium as a secondary coolant and had a peak temperature of 860 °C. It produced 100 MWh over nine days in 1954. This experiment used Inconel 600 alloy for the metal structure and piping.[4] After the ARE, another reactor was made critical at the Critical Experiments Facility of the Oak Ridge National Laboratory in 1957 as part of the circulating-fuel reactor program of the Pratt and Whitney Aircraft Company (PWAC). This was called the PWAR-1, the Pratt and Whitney Aircraft Reactor-1. The experiment was run for only a few weeks and at essentially zero nuclear power, but it was a critical reactor. The operating temperature was held constant at approximately 675 °C (1,250 °F). Like the 2.5 MW ARE, the PWAR-1 used NaF-ZrF4-UF4 as the primary fuel and coolant, making it one of the three critical molten salt reactors ever built.[5]

Molten-salt reactor experiment

MSRE plant diagram

Oak Ridge National Laboratory (ORNL) took the lead in researching the MSR through 1960s, and much of their work culminated with the Molten-Salt Reactor Experiment (MSRE). The MSRE was a 7.4 MWth test reactor simulating the neutronic "kernel" of a type of epithermal thorium molten salt breeder reactor called the liquid fluoride thorium reactor. The large, expensive breeding blanket of thorium salt was omitted in favor of neutron measurements.

The MSRE was located at ORNL. Its piping, core vat and structural components were made from Hastelloy-N and its moderator was pyrolytic graphite. It went critical in 1965 and ran for four years. The fuel for the MSRE was LiF-BeF2-ZrF4-UF4 (65-29-5-1), the graphite core moderated it, and its secondary coolant was FLiBe (2LiF-BeF2). It reached temperatures as high as 650 °C and operated for the equivalent of about 1.5 years of full power operation.

Oak Ridge National Laboratory molten salt breeder reactor

The culmination of the Oak Ridge National Laboratory research during the 1970–1976 timeframe resulted in a proposed molten salt breeder reactor (MSBR) design which would use LiF-BeF2-ThF4-UF4 (72-16-12-0.4) as fuel, was to be moderated by graphite with a 4-year replacement schedule, use NaF-NaBF4 as the secondary coolant, and have a peak operating temperature of 705 °C.[6] Despite the success, the MSR program closed down in the early 1970s in favor of the liquid metal fast-breeder reactor (LMFBR),[7] after which research stagnated in the United States.[8][9] As of 2011, the ARE and the MSRE remained the only molten-salt reactors ever operated.

The MSBR project received funding until 1976. Inflation-adjusted to 1991 dollars, the project received $38.9 million from 1968 to 1976.[10]

In 2016 Nobel prize winning physicist Carlo Rubbia, former Director General of CERN, claims one of the main reasons why research was cut is what makes it so attractive today — thorium is difficult to turn into a nuclear weapon, and advocated research into thorium as an energy source.[11]

The following reasons were officially cited as responsible for the program cancellation:

Oak Ridge National Laboratory denatured molten salt reactor (DMSR)

In 1980, the engineering technology division at Oak Ridge National Laboratory published a paper entitled "Conceptual Design Characteristics of a Denatured Molten-Salt Reactor with Once-Through Fueling." In it, the authors "examine the conceptual feasibility of a molten-salt power reactor fueled with denatured uranium-235 (i.e. with low-enriched uranium) and operated with a minimum of chemical processing." The main priority behind the design characteristics is proliferation resistance.[12] Lessons learned from past projects and research at ORNL were taken into strong consideration. Although the DMSR can theoretically be fueled partially by thorium or plutonium, fueling solely on low enriched uranium (LEU) helps maximize proliferation resistance.

Another important goal of the DMSR is to minimize R&D required and to maximize feasibility. The Generation IV international Forum (GIF) includes "salt processing" as a technology gap for molten salt reactors.[13] The DMSR requires minimal chemical processing because it is a burner design as opposed to a breeder. Both experimental reactors built at ORNL were burner designs. In addition, the choices to use graphite for neutron moderation, and enhanced Hastelloy-N for piping simplify the design and reduce R&D needed.

Russian MSR research program

In Russia, a molten-salt reactor research program was started in the second half of the 1970s at the Kurchatov Institute. It covered a wide range of theoretical and experimental studies, particularly the investigation of mechanical, corrosion and radiation properties of the molten salt container materials. The main findings of completed program supported the conclusion that there are no physical nor technological obstacles to the practical implementation of MSRs.[14] A reduction in activity occurred after 1986 due to the Chernobyl disaster, along with a general stagnation of nuclear power and nuclear industry.[15](p381)

Britain's Molten Salt Reactor program

While Alvin Weinberg's MSR work at Oak Ridge progressed in the US, Britain's Atomic Energy Research Establishment (AERE) were developing an alternative MSR design across its National Laboratories at Harwell, Culham, Risley and Winfrith. AERE decided that there would be little to gain from replicating ORNL's work, so they opted to focus on a lead-cooled 2.5GWe Molten Salt Fast Reactor (MSFR) concept using a chloride salt.[16] Also researching the option of using Helium gas as an alternative coolant.[17][18]

The UK MSFR would be fuelled by plutonium, a fuel considered to be 'free' by the program's research scientists, who viewed the UK's plutonium stockpiles as an asset rather than a liability. Despite developing quite different designs, ORNL and AERE seem to have had close contact during this period with information exchange and expert visits taking place. Theoretical work on the concept was conducted between 1964 and 1966, and experimental work was ongoing between 1968 and 1973. The program received government funding of around £100-200 thousand annually (equivalent to £2-3 million in 2005). This funding came to an end in 1974, partly due to the success of the Prototype Fast Reactor at Dounreay which was considered a priority for funding as it went critical in the same year.[16]

AERE reports and findings from its MSR Program conducted in the 60's and 70's are available for public viewing at the UK National Archives in Kew, London.[16]

In January 2016, the United States Department of Energy announced a $80m award fund to develop Generation IV reactor designs. Southern Company will use the funding to develop a molten chloride salt fast reactor.[19]

Recent developments

UK deployment study

A study on MSRs completed in July 2015 by Energy Process Developments, funded by Innovate UK, gives an summary of MSR activity internationally. It looks at the feasibility of developing a pilot scale demonstration MSR in the UK. A review of potential UK sites is given along with an insight into the UK regulatory process for innovative reactor technology. The technical review of six MSR designs led to the selection of the Stable Salt Reactor, designed by Moltex Energy, as most suitable for UK implementation.[20]

Molten salt waste-burner

Seaborg Technologies, a company based in Denmark, has recently been developing the core for a MSW (Molten Salt Waste-burner). The MSW is a high temperature, single salt, thermal MSR designed to go critical on a combination of thorium and nuclear waste from conventional nuclear reactors. Thorium produces much less of the long lived and problematic transuranic waste (e.g. plutonium and americium) than conventional reactor fuel, even when running a closed fuel cycle. As a consequence the core produces much less transuranic waste than it consumes – hence a waste-burner. The MSW design is modular and the reactor core is estimated to be replaced every 6–10 years, however, the fuel will not be replaced and will burn for the entire power plant lifetime. The first version of the Seaborg core is planned to produce 50 MWth power and is shown to reduce the amount of transuranic waste in the world by approximately 1 ton (not considering natural decays) over its 60 years power plant lifetime. After 60 years the 233U concentration in the fuel salt is high enough to initiate a closed thorium fuel cycle in the next generation power plant. Whitepaper.

Denatured molten salt reactor

Terrestrial Energy Inc. (TEI), a Canadian based company, is developing a DMSR design called the Integral Molten Salt Reactor (IMSR). The IMSR is designed to be deployable as a small modular reactor (SMR) and will be constructed in three power formulations ranging from 80 to 600 MW thermal power. With high operating temperatures, the IMSR has application in industrial heat markets as well as traditional power markets. The main design features include neutron moderation from graphite (thermal spectrum), fueling with low-enriched uranium, and a compact and replaceable Core-unit. The latter feature permits the operational simplicity necessary for industrial deployment.[21]

Liquid-salt very-high-temperature reactor

As of September 2010, research was continuing for reactors that utilize molten salts for coolant. Both the traditional molten-salt reactor and the very high temperature reactor (VHTR) were selected as potential designs for study under the Generation Four Initiative (GEN-IV). A version of the VHTR being studied was the liquid-salt very-high-temperature reactor (LS-VHTR), also commonly called the advanced high-temperature reactor (AHTR). It is essentially a standard VHTR design that uses liquid salt as a coolant in the primary loop, rather than a single helium loop. It relies on "TRISO" fuel dispersed in graphite. Early AHTR research focused on graphite would be in the form of graphite rods that would be inserted in hexagonal moderating graphite blocks, but current studies focus primarily on pebble-type fuel. The LS-VHTR has many attractive features, including: the ability to work at very high temperatures (the boiling point of most molten salts being considered are >1400 °C); low-pressure cooling that can be used to more easily match hydrogen production facility conditions (most thermochemical cycles require temperatures in excess of 750 °C); better electric conversion efficiency than a helium-cooled VHTR operating at similar conditions; passive safety systems, and better retention of fission products in the event of an accident. This concept is now referred to as "fluoride salt-cooled high-temperature reactor" (FHR).[22]

Liquid fluoride thorium reactor

Reactors containing molten thorium salt, called liquid fluoride thorium reactors (LFTR), would tap the abundant energy source of the thorium fuel cycle. Private companies from Japan, Russia, Australia and the United States, and the Chinese government, have expressed interest in developing this technology.[23][24][25]

Advocates estimate that five hundred metric tons of thorium could supply all U.S. energy needs for one year.[26] The U.S. Geological Survey estimates that the largest known U.S. thorium deposit, the Lemhi Pass district on the Montana-Idaho border, contains thorium reserves of 64,000 metric tons.[27]

Fuji reactor

The FUJI MSR is a 100 to 200 MWe LFTR, using technology similar to the Oak Ridge National Laboratory Reactor. It is being developed by a consortium including members from Japan, the U.S. and Russia. It would likely take 20 years to develop a full size reactor[28] but the project seems to lack funding.[23]

Chinese project

Under the direction of Jiang Mianheng, The People’s Republic of China has initiated a research project in thorium molten-salt reactor technology. It was formally announced at the Chinese Academy of Sciences (CAS) annual conference in January 2011. The plan was "to build a tiny 2 MW plant using liquid fluoride fuel by the end of the decade, before scaling up to commercially viable size over the 2020s. It is also working on a pebble-bed reactor."[25][29] The proposed completion date for a test 2 MW pebble-bed solid thorium and molten salt cooled reactor has been delayed from 2015 to 2017. The proposed "test thorium molten-salt reactor" has also been delayed.[30]

Indian research

Ratan Kumar Sinha, Chairman of Atomic Energy Commission of India, stated in 2013: "India is also investigating Molten Salt Reactor (MSR) technology. We have molten salt loops operational at BARC."[31]

U.S. companies

Kirk Sorensen, former NASA scientist and chief nuclear technologist at Teledyne Brown Engineering, has been a long-time promoter of the thorium fuel cycle, coining the term liquid fluoride thorium reactor. In 2011, Sorensen founded Flibe Energy, a company aimed at developing 20–50 MW LFTR reactor designs to power military bases. (It is easier to approve novel military designs than civilian power station designs in today's US nuclear regulatory environment).[24][32][33][34]

Another startup company, Transatomic Power, has been created by Ph.D. students from MIT including CEO Leslie Dewan and Mark Massie, and Russ Wilcox of E Ink.[35] They are pursuing what they term a Waste-Annihilating Molten Salt Reactor (acronym WAMSR), focused on the potential to consume existing spent nuclear fuel more thoroughly.[36] Transatomic received venture capital funding in early 2015.[37]

The Alvin Weinberg Foundation

The Alvin Weinberg Foundation is a British non-profit organization founded in 2011, dedicated to raising awareness about the potential of thorium energy and LFTR. It was formally launched at the House of Lords on 8 September 2011.[38][39][40] It is named after American nuclear physicist Alvin M. Weinberg, who pioneered the thorium molten salt reactor research.

European developments

The EVOL (Evaluation and viability of liquid fuel fast reactor system) project, with the objective of proposing a design of the MSFR (Molten Salt Fast Reactor),[41] released its final report in 2014.[42] The various molten salt reactor projects like FHR, MOSART, MSFR, and TMSR have common themes in basic R&D areas, according to a 2014 paper giving an overview of the MSR in a GenV context.[43] Another paper gives an overview of the MSFR.[44] More resources are available in the MSFR bibliography.[45]

Molten Chloride Fast Reactor (MCFR) research

In January 2016, the United States Department of Energy announced a $80m award fund to develop Generation IV reactor designs.[19] One of the two beneficiaries, Southern Company will use the funding to develop a Molten Chloride Fast Reactor (MCFR), a type of MSR developed earlier by British scientists.[16]

Molten-salt fueling options

Thorium is not for tomorrow but unless you do any development, it will not get there.
Dr Carlo Rubbia, Nobel Laureate and former Director General of CERN, January 2016[46]

Molten-salt-cooled reactors

Molten-salt-fueled reactors are quite different from molten-salt-cooled solid-fuel reactors, called simply "molten salt reactor system" in the Generation IV proposal, also called MSCR, which is also the acronym for the Molten Salt Converter Reactor design. These reactors were additionally referred to as "advanced high-temperature reactors (AHTRs), but since about 2010 the preferred DOE designation is "fluoride high-temperature reactors (FHRs)".[48]

The FHR concept cannot reprocess fuel easily and has fuel rods that need to be fabricated and validated, delaying deployment by up to twenty years from project inception. However, since it uses fabricated fuel, reactor manufacturers can still profit by selling fuel assemblies.

The FHR retains the safety and cost advantages of a low-pressure, high-temperature coolant, also shared by liquid metal cooled reactors. Notably, there is no steam in the core to cause an explosion, and no large, expensive steel pressure vessel. Since it can operate at high temperatures, the conversion of the heat to electricity can also use an efficient, lightweight Brayton cycle gas turbine.

Much of the current research on FHRs is focused on small compact heat exchangers. By using smaller heat exchangers, less molten salt needs to be used and therefore significant cost savings could be achieved.[49]

Molten salts can be highly corrosive, more so as temperatures rise. For the primary cooling loop of the MSR, a material is needed that can withstand corrosion at high temperatures and intense radiation. Experiments show that Hastelloy-N and similar alloys are quite suited to the tasks at operating temperatures up to about 700 °C. However, long-term experience with a production scale reactor has yet to be gained. In spite of serious engineering difficulties higher operating temperatures may be desirable – at 850 °C thermochemical production of hydrogen becomes possible. Materials for this temperature range have not been validated, though carbon composites, molybdenum alloys (e.g. TZM), carbides, and refractory metal based or ODS alloys might be feasible.

Fused salt selection

Molten FLiBe

The salt mixtures are chosen to make the reactor safer and more practical. Fluoride salts are favored, because fluorine has only one stable isotope (F-19), and it does not easily become radioactive under neutron bombardment. Both of these make fluorine better than chlorine, which has two stable isotopes (Cl-35 and Cl-37), as well as a slow-decaying isotope between them which facilitates neutron absorption by Cl-35. Compared to chlorine and other halides, fluorine also absorbs fewer neutrons and slows ("moderates") neutrons better. Low-valence fluorides boil at high temperatures, though many pentafluorides and hexafluorides boil at low temperatures. They also must be very hot before they break down into their simpler components, such molten salts are "chemically stable" when maintained well below their boiling points.

On the other hand, some salts are so useful that isotope separation of the halide is worthwhile. Chlorides permit fast breeder reactors to be constructed using molten salts. However, not nearly as much work has been done on reactor designs using chloride salts. Chlorine, unlike fluorine, must be purified to isolate the heavier stable isotope, chlorine-37, thus reducing production of sulfur tetrafluoride that occurs when chlorine-35 absorbs a neutron to become chlorine-36, then degrades by beta decay to sulfur-36.

Similarly, any lithium present in a salt mixture must be in the form of purified lithium-7, because lithium-6 effectively captures neutrons and produces tritium. Even if pure 7Li is used, salts containing lithium will cause significant tritium production, comparable with heavy water reactors.

Reactor salts are usually close to eutectic mixtures to reduce their melting point. A low melting point simplifies melting the salt at startup and reduces the risk of the salt freezing as it is cooled in the heat exchanger.

Due to the high "redox window" of fused fluoride salts, the redox potential of the fused salt system can be changed. Fluorine-Lithium-Beryllium ("FLiBe") can be used with beryllium additions to lower the redox potential and almost eliminate corrosion. However, since beryllium is extremely toxic, special precautions must be engineered into the design to prevent its release into the environment. Many other salts can cause plumbing corrosion, especially if the reactor is hot enough to make highly reactive hydrogen.

To date, most research has focused on FLiBe, because lithium and beryllium are reasonably effective moderators, and form a eutectic salt mixture with a lower melting point than each of the constituent salts. Beryllium also performs neutron doubling, improving the neutron economy. This process occurs when the beryllium nucleus re-emits two neutrons after absorbing a single neutron. For the fuel carrying salts, generally 1% or 2% (by mole) of UF4 is added. Thorium and plutonium fluorides have also been used.

Comparison of the neutron capture and moderating efficiency of several materials. Red are Be-bearing, blue are ZrF4-bearing and green are LiF-bearing salts.[50]
Material Total neutron capture
relative to graphite
(per unit volume)
Moderating ratio
(Avg. 0.1 to 10 eV)
Heavy water 0.2 11449
Light water 75 246
Graphite 1 863
Sodium 47 2
UCO 285 2
UO2 3583 0.1
2LiF–BeF2 8 60
LiF–BeF2–ZrF4 (64.5–30.5–5) 8 54
NaF–BeF2 (57–43) 28 15
LiF–NaF–BeF2 (31–31–38) 20 22
LiF–ZrF4 (51–49) 9 29
NaF–ZrF4 (59.5–40.5) 24 10
LiF-NaF–ZrF4 (26–37–37) 20 13
KF–ZrF4 (58–42) 67 3
RbF–ZrF4 (58–42) 14 13
LiF–KF (50–50) 97 2
LiF–RbF (44–56) 19 9
LiF–NaF–KF (46.5–11.5–42) 90 2
LiF–NaF–RbF (42–6–52) 20 8

Fused salt purification

Techniques for preparing and handling molten salt had been first developed at Oak Ridge National Lab.[51] The purpose of salt purification was to eliminate oxides, sulfur, and metal impurities. Oxides could result in the deposition of solid particles in reactor operation. Sulfur had to be removed because of their corrosive attack on nickel-base alloys at operational temperature. Structural metal such as chromium, nickel, and iron had to be removed for corrosion control.

A water content reduction purification stage using HF and helium sweep gas was specified to run at 400 °C. Oxide and sulfur contamination in the salt mixtures were removed using gas sparging of HF – H2 mixture, with the salt heated to 600 °C.[51](p8) Structural metal contamination in the salt mixtures were removed using hydrogen gas sparging, at 700 °C.[51](p26) Solid ammonium hydrofluoride was proposed as a safer alternative for oxide removal.[52]

Fused salt processing

The possibility of online processing can be an advantage of the MSR design. Continuous processing would reduce the inventory of fission products, control corrosion and improve neutron economy by removing fission products with high neutron absorption cross-section, especially xenon. This makes the MSR particularly suited to the neutron-poor thorium fuel cycle. Online fuel processing can introduce risks of fuel processing accidents,[53](p15) which can trigger release of radio isotopes.

In some thorium breeding scenarios, the intermediate product protactinium-233 would be removed from the reactor and allowed to decay into highly pure uranium-233, an attractive bomb-making material. More modern designs propose to use a lower specific power or a separate large thorium breeding blanket. This dilutes the protactinium to such an extent that few protactinium atoms absorb a second neutron or, via a (n, 2n) reaction (in which an incident neutron is not absorbed but instead knocks a neutron out of the nucleus), generate uranium-232. Because U-232 has a short half-life and its decay chain contains hard gamma emitters, it makes the isotopic mix of uranium less attractive for bomb-making. This benefit would come with the added expense of a larger fissile inventory or a 2-fluid design with a large quantity of blanket salt.

The necessary fuel salt reprocessing technology has been demonstrated, but only at laboratory scale. A prerequisite to full-scale commercial reactor design is the R&D to engineer an economically competitive fuel salt cleaning system.

Fissile fuel reprocessing issues

Changes in the composition of a MSR fast neutron (kg/GW)

Reprocessing refers to the chemical separation of fissionable uranium and plutonium from spent nuclear fuel.[54] The recovery of uranium or plutonium could be subject to the risk of nuclear proliferation. In the United States the regulatory regime has varied dramatically in different administrations.[54]

In the original 1971 Molten Salt Breeder Reactor proposal, uranium reprocessing was scheduled every ten days as part of reactor operation.[55](p181) Subsequently a once-through fueling design was proposed that limited uranium reprocessing to every thirty years at the end of useful salt life.[56](p98) A mixture of uranium-238 was called for to make sure recovered uranium would not be weapons grade. This design is referred to as denatured molten salt reactor.[57] If reprocessing were to be prohibited then the uranium would be disposed with other fission products.

Comparison to ordinary light water reactors

MSRs, especially those with the fuel dissolved in the salt differ considerably from conventional reactors. The pressure can be low and the temperature is much higher. In this respect an MSR is more similar to a liquid metal cooled reactor than a conventional light water cooled reactor. As an additional difference MSRs are often planned as breeding reactors with a closed fuel cycle – as opposed to the once-through fuel currently used in U.S. nuclear reactors.

The typical safety concepts rely on a negative temperature coefficient of reactivity and a large possible temperature rise to limit reactivity excursions. As an additional method for shutdown a separate, passively cooled container below the reactor is planned. In case of problems and for regular maintenance the fuel is drained from the reactor. This stops the nuclear reaction and gives a second cooling system. Neutron-producing accelerators have even been proposed for some super-safe subcritical experimental designs.[58]

Cost estimates from the 1970s were slightly lower than for conventional light-water reactors.[59]

The temperatures of some proposed designs are high enough to produce process heat for hydrogen production or other chemical reactions. Because of this, they have been included in the GEN-IV roadmap for further study.[60]

Advantages

The molten salt reactor offers many potential advantages compared to current light water reactors:[6]

Disadvantages

See also

References

  1. Williams, Stephen (16 January 2015). "Molten Salt Reactors: The Future of Green Energy?". ZME Science. Retrieved 18 February 2015.
  2. http://www.world-nuclear.org/info/Current-and-Future-Generation/Molten-Salt-Reactors/
  3. Ehresman, Teri (ed.). Molten Salt Reactor (MSR) (PDF) (Fact Sheet). 08-GA50044-17-R1 R6-11. Idaho National Laboratory.
  4. 1 2 Rosenthal, Murry. An Account of Oak Ridge National Laboratory's Thirteen Nuclear Reactors, ORNL/TM-2009/181.
  5. Scott, D.; Alwang, G.W.; Demski, E.F.; Fader, W.J.; Sandin, E.V.; Malenfant, R.E. (1958) A ZERO POWER REFLECTOR-MODERATED REACTOR EXPERIMENT AT ELEVATED TEMPERATURE. Oak Ridge National Lab.
  6. 1 2 Section 5.3, WASH 1097. Energy From Thorium's Document Repository "The Use of Thorium in Nuclear Power Reactors". ORNL.gov
  7. 1 2 3 MacPherson, H. G. (1985). "The Molten Salt Reactor Adventure" (PDF). Nuclear Science and Engineering 90: 374–380.
  8. Weinberg, Alvin (1997). The First Nuclear Era: The Life and Times of a Technological Fixer. Springer. ISBN 978-1-56396-358-2.
  9. "ORNL: The First 50 Years". Retrieved 12 November 2011. |chapter= ignored (help)
  10. Cohen, Linda R.; Noll, Roger G. (1991). The Technology pork barrel. Brookings Institution. p. 234. ISBN 0-8157-1508-0. Retrieved 28 February 2012.
  11. "for nuclear energy looms". Retrieved 26 January 2016.
  12. Engel, J.R. (1980) "Conceptual Design Characteristics of a Denatured Molten-Salt Reactor with Once-Through Fueling." Oak Ridge National Laboratory: Engineering Technology Division.
  13. A Technology Roadmap for Generation IV Nuclear Energy Systems. P. 34. U.S. DOE Nuclear Energy Research Advisory Committee and the Generation IV International Forum. Copyright 2002.
  14. The results of the investigations of Russian Research Center—‘‘Kurchatov Institute’’ on molten salt applications to problems of nuclear energy systems at AIP Conference Proceedings July 1994: v. 346, pp. 138–147
  15. Advanced Reactors with Innovative Fuels. 1 October 1999. ISBN 9789264171176.
  16. 1 2 3 4 http://www.the-weinberg-foundation.org/2014/11/13/the-uks-forgotten-molten-salt-reactor-programme/
  17. http://moltensalt.org/references/static/downloads/pdf/AEEW-R956.pdf
  18. http://static.smallworldlabs.com/iet/user_content/files/081/023/81023421/a94db54e20bb976a6821c7c381c8cfa5-aeew--r1059.pdf
  19. 1 2 "Energy Department Announces New Investments in Advanced Nuclear Power Reactors...". US Department of Energy. Retrieved 16 January 2016.
  20. Griffiths, Trevor; Tomlinson, Jasper; O’Sullivan, Rory. "MSR Review - Feasibility of Developing a Pilot Scale Molten Salt Reactor in the UK" (PDF). Energy Process Developments. Retrieved 14 January 2016.
  21. Integral Molten Salt Reactor. terrestrialenergy.com
  22. Fluoride Salt-Cooled High-Temperature Reactor Workshop Announcement and Call for Participation, c. September 2010, at Oak Ridge National Laboratory, Oak Ridge Tennessee, USA. Accessed 18 March 2013
  23. 1 2 Barton, Charles (March 2008) Interview with Ralph Moir at Energy From Thorium blog
  24. 1 2 Kirk Sorensen has Started a Thorium Power Company at NextBigFuture blog, 23 May 2011
  25. 1 2 Evans-Pritchard, Ambrose (6 January 2013) China blazes trail for 'clean' nuclear power from thorium The Daily Telegraph, UK. Accessed 18 March 2013
  26. Hargraves, Robert; Moir, Ralph (July 2010). "Liquid Fluoride Thorium Reactors". American Scientist 98 (4): 304–313. doi:10.1511/2010.85.304.
  27. Van Gosen, B. S.; Armbrustmacher, T. J. (2009), Thorium deposits of the United States – Energy resources for the future?, Circular 1336, U.S. Geological Survey
  28. Fuji Molten salt reactor. nextbigfuture.com. 19 December 2007
  29. Clark, Duncan (16 February 2011). "China enters race to develop nuclear energy from thorium". The Guardian.
  30. Completion date slips for China’s thorium molten salt reactor At Weinberg Foundation website, 30 October 2012
  31. Jha, Saurav (16 September 2013). "The Thorium Question – An interview with India's nuclear czar". Retrieved 19 September 2013.
  32. "Flibe Energy". flibe-energy.com.
  33. "Live chat: nuclear thorium technologist Kirk Sorensen". The Guardian. 7 September 2011.
  34. "New Huntsville company to build thorium-based nuclear reactors". huntsvillenewswire.com.
  35. "A Pair of MIT Scientists Try to Transform Nuclear Power". Forbes. 27 September 2012.
  36. "New nuke could power world until 2083". The Register. 14 March 2013.
  37. Kyle Alspach (2015-02-10). "MIT Startup Gets $2.5M to Develop the Nuclear Reactor We've Been Waiting For". BostInno Streetwise. Retrieved 2015-12-19.
  38. Clark, Duncan (9 September 2011). "Thorium advocates launch pressure group". The Guardian.
  39. "London: Weinberg Foundation to heat up campaign for safe, green,... – The Weinberg Foundation". Mynewsdesk.
  40. "New NGO to fuel interest in safe thorium nuclear reactors". businessgreen.com.
  41. http://cordis.europa.eu/result/rcn/57550_en.html
  42. http://cordis.europa.eu/docs/results/249/249696/final1-final-report-f.pdf
  43. http://lpsc.in2p3.fr/images/ActivitesScientifiques/Physique_des_Reacteurs/PDF/ArticlePNE2014_MSR-GIF_final.pdf
  44. http://lpsc.in2p3.fr/images/ActivitesScientifiques/Physique_des_Reacteurs/PDF/ANUCEN-64-2014_StartingModesMSFR.pdf
  45. http://lpsc.in2p3.fr/index.php/en/groupes-de-physique/enjeux-societaux/physique-des-reacteurs/systemes-et-scenarios/rsf-reacteurs-a-sels-fondus/38-activites-scientifiques/physique-des-reacteurs-nucleaires/183-msfr-bibliographie
  46. "An alternative fuel for nuclear energy looms". SciDev. Retrieved 26 January 2016.
  47. Gat, Uri; Engel, J. R.; Dodds, H. L. (28 February 1991), "The Molten Salt Reactor Option for Beneficial Use of Fissile Material from Dismantled Weapons", AAAS session on Fissile Materials from Nuclear Arms Reduction (PDF), Oak Ridge National Laboratory, TN
  48. Greene, Sherrel (May 2011). Fluoride Salt-cooled High Temperature Reactors – Technology Status and Development Strategy. San Francisco, CA.
  49. Forsberg, Charles (November 2011) Fluoride-Salt-Cooled High-Temperature Reactors for Power and Process Heat. mit.edu
  50. Ingersoll, D. T. (December 2005). "ORNL/TM-2005/218, Status of Physics and Safety Analyses for the Liquid-Salt-Cooled Very High-Temperature Reactor (LS-VHTR)" (PDF). ORNL. Retrieved 13 May 2010.
  51. 1 2 3 Shaffer, J. H. (January 1971), Preparation and Handling of Salt Mixtures for the Molten Salt Reactor Experiment (PDF), ORNL-4616, Oak Ridge National Laboratory
  52. Ignatiev, Victor (1 April 2010). Critical issues of nuclear energy systems employing molten salt fluorides (PDF). Lisbon, Portugal: ACSEPT.
  53. CForsberg, Charles (June 2004). "Safety and Licensing Aspects of the Molten Salt Reactor" (PDF). 2004 American Nuclear Society Annual Meeting. Pittsburgh, Pennsylvania: American Nuclear Society.
  54. 1 2 Andrews, Anthony (27 March 2008), "Nuclear Fuel Processing: U.S. Policy Development" (PDF), CRS Report for Congress (Congressional Research Service), RS22542
  55. Rosenthal, M.; Briggs, R.; Haubenreich, P., Molten-Salt Reactor Program: Semiannual Progress Report for Period Ending August 31, 1971 (PDF), ORNL-4728, Oak Ridge National Laboratory
  56. 1 2 J. R. Engel; et al. (1980). "Conceptual design characteristics of a denatured molten-salt reactor with once-through fueling" (PDF). ORNL/TM-7207. Oak Ridge National Lab, TN.
  57. LeBlanc, D. (2010) Denatured Molten Salt Reactors (DMSR): An Idea Whose Time Has Finally Come?. 31st Annual conference of the Canadian Nuclear Society & 34th CNS/CNA student conference, Vol. 2 of 2 ( 24–27 May 2010) Montreal, Quebec, Canada. ISBN 978-1-61782-363-3
  58. Plutonium(TRU) Transmutation and 233U Production by Single-Fluid Type Accelerator Molten-Salt Breeder (AMSB) Kazuo Furukawa, Yoshio Kato, Sergey E. Chigrinov, Int. Conf. Accelerator-driven Transmutation, Tech. Appl. (Las Vegas, 25–29 July 1994)
  59. Moir, M. W. (2002). "Cost of Electricity from Molten Salt Reactors (MSR)" (PDF) 138. Nuclear Technology: 93–95.
  60. US DOE Nuclear Energy Research Advisory Committee (2002). "A Technology Roadmap for Generation IV Nuclear Energy Systems" (PDF). GIF-002-00.
  61. Finnish research network for generation four nuclear energy systems. vtt.fi
  62. "Is the "Superfuel" Thorium Riskier Than We Thought?". Popular Mechanics. 5 December 2012.

Further reading

External links

Wikimedia Commons has media related to Molten salt reactors.
This article is issued from Wikipedia - version of the Thursday, May 05, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.