Euler spiral

A double-end Euler spiral. The curve continues to converge to the points marked, as t tends to positive or negative infinity.

An Euler spiral is a curve whose curvature changes linearly with its curve length (the curvature of a circular curve is equal to the reciprocal of the radius). Euler spirals are also commonly referred to as spiros, clothoids, or Cornu spirals.

Euler spirals have applications to diffraction computations. They are also widely used as transition curve in railroad engineering/highway engineering for connecting and transiting the geometry between a tangent and a circular curve. The principle of linear variation of the curvature of the transition curve between a tangent and a circular curve defines the geometry of the Euler spiral:

Applications

Track transition curve

Animation depicting evolution of a Cornu spiral with the tangential circle with the same radius of curvature as its tip (click on thumbnail to observe).

An object traveling on a circular path experiences a centripetal acceleration. When a vehicle traveling on a straight path suddenly transitions to a tangential circular path, it experiences a sudden centripetal acceleration starting at the tangent point; and this centripetal force acts instantly causing much discomfort (causing jerk).

On early railroads this instant application of lateral force was not an issue since low speeds and wide-radius curves were employed (lateral forces on the passengers and the lateral sway was small and tolerable). As speeds of rail vehicles increased over the years, it became obvious that an easement is necessary so that the centripetal acceleration increases linearly with the traveled distance. Given the expression of centripetal acceleration V² / R, the obvious solution is to provide an easement curve whose curvature, 1 / R, increases linearly with the traveled distance. This geometry is an Euler spiral.

Unaware of the solution of the geometry by Leonhard Euler, Rankine cited the cubic curve (a polynomial curve of degree 3), which is an approximation of the Euler spiral for small angular changes in the same way that a parabola is an approximation to a circular curve.

Marie Alfred Cornu (and later some civil engineers) also solved the calculus of Euler spiral independently. Euler spirals are now widely used in rail and highway engineering for providing a transition or an easement between a tangent and a horizontal circular curve.

Optics

The Cornu spiral can be used to describe a diffraction pattern.[1]

Formulation

Symbols

R\, Radius of curvature
R_c\, Radius of Circular curve at the end of the spiral
\theta\, Angle of curve from beginning of spiral (infinite R) to a particular point on the spiral.
This can also be measured as the angle between the initial tangent and the tangent at the concerned point.
\theta _s\, Angle of full spiral curve
L , s\, Length measured along the spiral curve from its initial position
L_s , s_o\, Length of spiral curve

Expansion of Fresnel integral

Main article: Fresnel integral

If a = 1, which is the case for normalized Euler curve, then the Cartesian coordinates are given by Fresnel integrals (or Euler integrals):

\begin{align}      C(L) &=\int_0^L\cos(s^2) \, ds\\
      S(L) &= \int_0^L\sin(s^2) \, ds\end{align}

Expand C(L) according to power series expansion of cosine:

      \cos \theta = 1 - \frac{\theta^2}{2!} + \frac{\theta^4}{4!} - \frac{\theta^6}{6!} + \cdots
\begin{align}      C(L) &= \int_0^L \cos(s^2) \, ds \\
           &= \int_0^L \left(1 - \frac{s^4}{2!} + \frac{s^8}{4!} - \frac{s^{12}}{6!} + \cdots\right) \,  ds\\

           &= L - \frac{L^5}{5 \times 2!} + \frac{L^9}{9 \times 4!} - \frac{L^{13}}{13 \times 6!} +\cdots\end{align}

Expand S(L) according to power series expansion of sine:

      \sin \theta = \theta - \frac{\theta^3}{3!} + \frac{\theta^5}{5!} - \frac{\theta^7}{7!} + \cdots
\begin{align}      S(L) &= \int_0^L \sin(s^2) \, ds\\
           &= \int_0^L \left(s^2 - \frac{s^6}{3!} + \frac{s^{10}}{5!} - \frac{s^{14}}{7!} + \cdots\right) \,  ds\\
           &= \frac{L^3}{3} - \frac{L^7}{7 \times 3!} + \frac{L^{11}}{11 \times 5!} - \frac{L^{15}}{15 \times 7!} +\cdots\end{align}

Normalization and conclusion

For a given Euler curve with:

2RL = 2R_c L_s = \frac{1}{a^2} \,

or

\frac{1}{R} = \frac{L}{R_c L_s} = 2a^2L \,

then

x=\frac{1}{a} \int_0^{L'} \cos s^2 \, ds
y=\frac{1}{a} \int_0^{L'} \sin s^2 \, ds \,

where L' = aL \, and a = \frac{1}{\sqrt{2R_c L_s}}.

The process of obtaining solution of (x, y) of an Euler spiral can thus be described as:

In the normalization process,


\begin{align}
R'_c & = \frac{R_c}{\sqrt{2 R_c L_s}} \\
     & = \sqrt{\frac{R_c}{2L_s}} \\
\end{align}

\begin{align}
L'_s & = \frac{L_s}{\sqrt{2R_c L_s}} \\
     & = \sqrt{\frac{L_s}{2R_c}}
\end{align}

Then


\begin{align}
2R'_c L'_s & = 2 \sqrt{\frac{R_c}{2L_s} } \sqrt{\frac{L_s}{2 R_c}} \\
           & = \tfrac{2}{2} \\
           & = 1
\end{align}

Generally the normalization reduces L' to a small value (<1) and results in good converging characteristics of the Fresnel integral manageable with only a few terms (at a price of increased numerical instability of the calculation, esp. for bigger \theta\, values.).


Illustration

Given:


   \begin{align}
   R_c & = 300\mbox{m} \\
   L_s &= 100\mbox{m}
   \end{align}

Then


   \begin{align}
   \theta_s & = \frac{L_s} {2R_c} \\
       & = \frac{100} {2 \times 300} \\
       & = 0.1667 \ \mbox{radian} \\
    \end{align}

And

 2R_c L_s = 60,000 \,

We scale down the Euler spiral by √60,000, i.e.100√6 to normalized Euler spiral that has:


   \begin{align}
      R'_c = \tfrac{3}{\sqrt{6}}\mbox{m} \\
      L'_s = \tfrac{1}{\sqrt{6}}\mbox{m} \\
      \\
   \end{align}

   \begin{align}
   2R'_c L'_s & = 2 \times \tfrac{3}{\sqrt{6}} \times \tfrac{1}{\sqrt{6}} \\
              & = 1 
   \end{align}

And


   \begin{align}
    \theta_s & = \frac{L'_s}{2R'_c} \\
       & = \frac{\tfrac{1}{\sqrt{6}}} {2 \times \tfrac{3}{\sqrt{6}}} \\
       & = 0.1667 \ \mbox{radian} \\
   \end{align}

The two angles \theta_s\, are the same. This thus confirms that the original and normalized Euler spirals are geometrically similar. The locus of the normalized curve can be determined from Fresnel Integral, while the locus of the original Euler spiral can be obtained by scaling back / up or denormalizing.

Other properties of normalized Euler spirals

Normalized Euler spirals can be expressed as:

x = \int_0^L \cos s^2 ds
y = \int_0^L \sin s^2 ds

Or expressed as power series:

x = \left . \sum_{i=0}^{\infty} \frac{(-1)^i}{(2i)!} \frac{s^{4i+1}}{4i+1} \right |_0^{L} =\sum_{i=0}^{\infty} \frac{(-1)^i}{(2i)!} \frac{L^{4i+1}}{4i+1}
y = \left . \sum_{i=0}^{\infty} \frac{(-1)^i}{(2i+1)!} \frac{s^{4i+3}}{4i+3} \right |_0^{L} =\sum_{i=0}^{\infty} \frac{(-1)^i}{(2i+1)!} \frac{L^{4i+3}}{4i+3}

The normalized Euler spiral will converge to a single point in the limit, which (noting that L = s) can be expressed as:

x^\prime = \lim_{s \to \infty} \int_0^{L} \cos (s^2) ds = \frac{1}{2} \sqrt{\frac{\pi}{2}}
y^\prime = \lim_{s \to \infty} \int_0^{L} \sin (s^2) ds = \frac{1}{2} \sqrt{\frac{\pi}{2}}

Normalized Euler spirals have the following properties:

2 R_c L_s = 1 \,\!
\theta_s = \frac{L_s}{2 R_c} = L_s ^2

And

\theta = \theta _s\cdot\frac{L^2}{L_s^2} = L^2
\frac{1}{R} = \frac{d\theta}{dL} = 2L

Note that 2R_c L_s = 1 also means 1/R_c = 2L_s, in agreement with the last mathematical statement.

Code for producing an Euler spiral

The following Sage code produces the second graph above. The first four lines express the Euler spiral component. Fresnel functions could not be found. Instead, the integrals of two expanded Taylor series are adopted. The remaining code expresses respectively the tangent and the circle, including the computation for the center coordinates.

var('L')
p = integral(taylor(cos(L^2), L, 0, 12), L)
q = integral(taylor(sin(L^2), L, 0, 12), L)
r1 = parametric_plot([p, q], (L, 0, 1), color = 'red')
r2 = line([(-1.0, 0), (0,0)], rgbcolor = 'blue')
x1 = p.subs(L = 1)
y1 = q.subs(L = 1)
R = 0.5
x2 = x1 - R*sin(1.0)
y2 = y1 + R*cos(1.0)
r3 = circle((x2, y2), R, rgbcolor = 'green')
show(r1 + r2 + r3, aspect_ratio = 1, axes=false)

The following is Mathematica code for the Euler spiral component (it works directly in wolframalpha.com):

ParametricPlot[{
  FresnelC[Sqrt[2/\[Pi]] t]/Sqrt[2/\[Pi]],
  FresnelS[Sqrt[2/\[Pi]] t]/Sqrt[2/\[Pi]]
}, {t, -10, 10}]

The following is Xcas code for the Euler spiral component:

plotparam([int(cos(u^2),u,0,t),int(sin(u^2),u,0,t)],t,-4,4)

The following is Sage code for the complete double ended Euler spiral:

s = var('s')
parametric_plot((lambda s: numerical_integral(cos(x**2),0,s)[0], lambda s: numerical_integral(sin(x**2),0,s)[0]), (-3*pi/2, 3*pi/2))

The following is JavaScript code for drawing an Euler spiral on a canvas element:

function drawEulerSpiral(canvas, T, N, scale) {
      ctx = canvas.getContext("2d");
      var dx, dy, t=0, prev = {x:0, y:0}, current;
      var dt = T/N;
      ctx.beginPath();
      while (N--) {
         dx = Math.cos(t*t) * dt;
         dy = Math.sin(t*t) * dt;
         t += dt;
         current = {
            x: prev.x + dx,
            y: prev.y + dy
         };
         ctx.lineTo(current.x*scale, current.y*scale);
         prev = current;
      }
      ctx.stroke();
}
drawEulerSpiral(document.getElementById("myCanvas"),10,10000,100)

See also

References

Notes

  1. Eugene Hecht (1998). Optics (3rd edition). Addison-Wesley. p. 491. ISBN 0-201-30425-2.

Sources

Further reading

External links

This article is issued from Wikipedia - version of the Monday, May 02, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.