Jersey barrier

42-inch (110 cm)-high variation of the Jersey barrier known as an Ontario Tall Wall, used to deflect vehicles from crossing into the opposing lanes of traffic.

A Jersey barrier or Jersey wall is a modular concrete or plastic barrier employed to separate lanes of traffic. It is designed to minimize vehicle damage in cases of incidental contact while still preventing the crossover case of a head-on collision. Jersey barriers are also used to reroute traffic and protect pedestrians during highway construction, as well as temporary and semi-permanent protections against landborne attack such as suicide vehicle bombs. A Jersey barrier is also known in the western United States as K-rail, a term borrowed from the California Department of Transportation specification for temporary concrete traffic barriers, or colloquially as a Jersey bump. Plastic water barriers of the same general shape are also now commonly referred to as Jersey barriers.

Development and use

Jersey barriers on the road.
Soldiers taking cover from enemy fire behind Jersey barriers in Baghdad, Iraq, 2007.

The Jersey barrier, also called New Jersey wall, was developed at the Stevens Institute of Technology in the 1950s (introduced in current form in 1959),[1] New Jersey, United States, under the direction of the New Jersey State Highway Department to divide multiple lanes on a highway.[2] A typical Jersey barrier stands 32 inches (81 cm) tall and is made of steel-reinforced poured concrete or plastic.[3] Many are constructed with the embedded steel reinforcement protruding from each end, allowing them to be incorporated into permanent emplacements when linked to one another by sections of fresh concrete poured on-site.

Their widespread use in road construction has led to wide application as a generic, portable barrier during construction projects and temporary rerouting of traffic into stopgap carpool and rush hour reversing highway lanes.[4]

The design of the Jersey barrier was specifically intended to minimize damage in incidental accidents and reduce the likelihood of a car crossing into oncoming lanes in the event of a collision. In common shallow angle hits, sheet metal damage is minimized by allowing the vehicle tires to ride up on the lower sloped face. Head-ons are minimized by gradually lifting the vehicle and pivoting it away from oncoming vehicles and back into traffic heading in its original direction.

Modern variations include the constant slope barrier and the F-shape barrier. The F-shape is generally similar to the Jersey barrier in appearance but is taller with somewhat different angles.[4]

The UK equivalent is the concrete step barrier.

First tested in 1968 by the then Department of Highways in Ontario, Canada, the Ontario Tall Wall is a variant of the Jersey barrier.[5] Standing at 42 inches (107 cm), it is 10 inches (25 cm) taller than the standard Jersey barrier. In Ontario, the Ministry of Transportation is replacing guiderails (steel guardrail and steel box-beam) with these barriers on 400-series highways.

The New Jersey Turnpike Authority developed and tested a similar, but heavily reinforced, design. This barrier design has been credited with effectively containing and redirecting larger vehicles, including semi-trailer (tractor-trailer) trucks.[4] The states of New York, Massachusetts, and New Jersey have adopted the taller barrier for their roads, as compared to the standard 32 inches (81 cm) suggested by the Federal Highway Administration.[5]

Designs with two rectangular notches at the bottom (through the short axis) allow for forklift-style lifting by front-end loaders. Barriers meant for short-term placement—especially in military and security barrier uses—might include steel rebar loops embedded in the top surface for rapid hook-and-cable system lifting.

The 2010 G-20 Toronto summit used a modified modular Jersey barriers with wired fencing bolted onto the concrete. The fence used the barrier as sturdy base to prevent protesters from toppling the fence around the security zone at the Metro Toronto Convention Centre.

The U.S. military nicknamed the devices as "Qaddafi Blocks" after truck bomb attacks in Beirut in 1983 resulted in more widespread use in military installations. Sometimes they are deployed to form a chicane to slow vehicular traffic arriving at military installations or other secure areas.

Plastic Jersey barriers

Hollow polyethylene barriers have been developed for short-term applications where portability is important. These plastic barriers are normally filled with water after placement on-site to provide a moderate level of crash protection. They are not designed to deflect vehicles, so vehicles may penetrate the barriers.[6] These barriers can also be filled with soil, spill, or concrete to produce a heavier barrier with greater crash protection, at the cost of reduced portability.

See also

References

  1. ↑ "New Jersey Median Barrier History". Roadstothefuture.com. Retrieved 13 December 2014.
  2. ↑ Laurie, Maxine; Mappen, Marc, eds. (2005). Encyclopedia of New Jersey. Rutgers University Press. p. 422.
  3. ↑ Federal Highway Administration (FHWA). Washington, D.C. "Concrete Barriers." FHWA Safety Programme. 2010-09-24.
  4. 1 2 3 McDevitt, Charles F. (March–April 2000). "Basics of Concrete Barriers". Public Roads (Washington, D.C.: Federal Highway Administration) 63 (5).
  5. 1 2 Giblin, Kelly A. (Summer 2006). "The Jersey Barrier". Invention & Technology (American Heritage Publishing) 22 (1). Archived from the original on June 9, 2010.
  6. ↑ FHWA. "NCHRP Report 350: Devices in Work Zones - Category 3". Recommended Procedures for the Safety Performance Evaluation of Highway Features. 2004-04-05.

External links

Wikimedia Commons has media related to Jersey barriers.
This article is issued from Wikipedia - version of the Friday, April 01, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.