PICAXE

PICAXE 20M2

PICAXE is a microcontroller system based on a range of Microchip PIC microcontrollers. PICAXE devices are essentially Microchip PIC devices, with pre-programmed firmware that enables bootloading of code directly from a PC, simplifying hobbyist embedded development. PICAXE devices have been produced by Revolution Education (Rev-Ed) since 1999.

Hardware

General

There are currently six (6) PICAXE variants of differing pin counts (8-14-18-20-28-40) and are available as DIL and SMD.^[1]

PICAXE microcontrollers are pre-programmed with an interpreter^[2] similar to the BASIC Stamp but using internal EEPROM instead, thus reducing cost. This also allows downloads to be made with a simple serial connection which eliminates the need for a PIC programmer.^[3] PICAXE is programmed using an RS-232 serial cable^[4] or a USB cable^[5] which connects a computer to the download circuit, which normally uses a 3.5 mm jack and two resistors.^[6]

Programming language

PICAXE microcontrollers are programmed using BASIC.^[7]

The PICAXE interpreter features bit-banged communications:

• Serial^[8][9] (asynchronous serial)
• SPI^[10][11] (synchronous serial)
• Infrared (using a 38 kHz carrier, seven data bits and five ID bits)^[12]
• One-wire^[13][14]

The 'readtemp' command reads the temperature from a DS18B20 temperature sensor and converts it into Celsius.^[15]

All current PICAXEs have commands for using hardware features of the underlying PIC microcontrollers:

• Hardware asynchronous serial^[16]
• Hardware synchronous serial^[17][18]
• Hardware PWM^[19]
• DAC^[20]
• ADC^[21]
• SR Latch^[22]
• Timers (two on X2/X1 parts^[23][24] which have settable intervals, only one on M2 parts with a fixed interval,^[25] older parts have none)
• Comparators^[26]
• Internal temperature measurement^[27]

Program space

All current PICAXE chips have at least 2048 bytes of on board program memory available for user programs:^[1]

• 08M2 - 2048 bytes
• 14M2 - 2048
• 18M2+ - 2048
• 20M2 - 2048
• 20X2 - 4096
• 28X1 - 4096
• 40X1 - 4096
• 28X2 - 4096 per slot with four slots for a total of 16 KiB
• 40X2 - 4096 per slot with four slots for a total of 16 KiB

Clock speeds

The default clock speed for all M2 and X1 parts is 4 MHz and for the X2 parts is 8 MHz.

The SETFREQ command allows speeds from 31 kHz up to 8 MHz for X1 parts, 31 kHz up to 32 MHz for M2 parts and 31 kHz up to 16 MHz for X2 parts (up to 64 MHz for the 20X2) using the internal resonator.

An external resonator can be used with the X1 parts for from 4 MHz to 20 MHz clock speeds and with the X2 parts for 16 MHz to 64 MHz clock speeds.^[28]

Project boards

Project boards for different applications are sold^[29] by Rev-Ed which contain the PICAXE, download circuit and may also contain a prototyping area^[30] or high power output drivers.^[31]

Software

Revolution Education develop software for writing programs for PICAXE.

PICAXE Programming Editor

PICAXE Programming Editor is a Windows-only IDE for writing PICAXE programs in BASIC code or a simple flowchart.

PICAXE Programming Editor features:^[32]

• source code colour syntax highlighting
• auto indentation
• syntax check and program download
• code explorer to shown variable, label and constant values
• full on screen simulation with animated chips and line by line code highlighting
• simulation breakpoints by line number and variable value
• debug and serial terminal windows
• AXE027 download cable testing and port identification tools
• various testing tools such as the analogue calibration wizard
• various code generation wizards (pwmout, tune, RTC setting, etc.)

AXEpad

AXEpad is a cross-platform application recommended for Linux and Mac users.^[33] It lacks some of Programming Editor's wizards, simulation and MDI.

Logicator for PICAXE

Logicator is an easy to use shareware flowcharting program.^[34] The Logicator web page is out of date as the free version does support all commands but shows nag screens.

PICAXE Programming Editor 6, the successor to PICAXE Programming Editor 5, has Logicator flowcharting merged into it so separate Logicator software is no longer required.^[35] Like PICAXE Programming Editor 5, PICAXE Programming Editor 6 is freeware.

Third-party software

Yenka

Yenka is a program developed by Crocodile Clips Ltd which has flowcharts and simulation.^[36]

Others

Many companies and organizations have put out their own editors with special features. Some include language translators or serial connectors, so there is a wide variety of consoles to be used.

Support

Support is available at the Technical Support section of the PICAXE website and at the PICAXE Forum.^[37]

The PICAXE Forum has a finished projects section where completed projects and PICAXE programs are posted,^[38] plus there is a similar section on the PICAXE website.^[39]

See also

• Arduino
• ARM express BASICchip
• BASIC Atom
• BASIC Stamp
• Maximite
• OOPic

References

1. "PICAXE Chip Sizes".
2. "poke - BASIC Commands - PICAXE".
3. "What is PICAXE? - PICAXE".
4. "Serial (9-way D) Download Cable - Hardware - PICAXE".
5. "PICAXE USB Download Cable (AXE027) - Hardware - PICAXE".
6. "PICAXE Download Circuit".
7. "Index of - BASIC Commands - PICAXE".
8. "serin - BASIC Commands - PICAXE".
9. "serout - BASIC Commands - PICAXE".
10. "shiftin - BASIC Commands - PICAXE".
11. "shiftout - BASIC Commands - PICAXE".
12. "irin - BASIC Commands - PICAXE".
13. "owin - BASIC Commands - PICAXE".
14. "owout - BASIC Commands - PICAXE".
15. "readtemp - BASIC Commands - PICAXE".
16. "hsersetup - BASIC Commands - PICAXE".
17. "hspisetup - BASIC Commands - PICAXE".
18. "hi2csetup - BASIC Commands - PICAXE".
19. "hpwm - BASIC Commands - PICAXE".
20. "dacsetup - BASIC Commands - PICAXE".
21. "readadc10 - BASIC Commands - PICAXE".
22. "srlatch - BASIC Commands - PICAXE".
23. "settimer - BASIC Commands - PICAXE".
24. "tmr3setup - BASIC Commands - PICAXE".
25. "enabletime - BASIC Commands - PICAXE".
26. "compsetup - BASIC Commands - PICAXE".
27. "readinternaltemp - BASIC Commands - PICAXE".
28. "setfreq - BASIC Commands".
29. "Project Boards - Hardware".
30. "PICAXE-08 Proto Board (AXE021) - Hardware - PICAXE".
31. "PICAXE-18 High Power Project Board (CHI035) - Hardware - PICAXE".
32. "PICAXE Programming Editor (BAS805) - Software - PICAXE".
33. "AXEPAD (PAD001) - Software - PICAXE".
34. "Logicator for PICAXE (LGC010) - Software - PICAXE".
35. "PE6 Beta testing Briefing" (PDF).
36. "Yenka PICs".
37. "Technical Support - Getting Started - PICAXE".
38. "Finished User PICAXE Projects".
39. "Index of - Project Gallery - PICAXE".

Further reading

• Lincoln, David (December 13, 2010). Programming and Customizing the PICAXE Microcontroller (2nd ed.). Mc Graw Hill/Tab Electronics. ISBN 978-0-07-174554-3.

• Hackett, Ron (August 12, 2010). PICAXE Microcontroller Projects for the Evil Genius (1st ed.). Mc Graw Hill/Tab Electronics. ISBN 9780071703260.

External links

• Official PICAXE Website
• BASIC commands
• web server/PICAXE interface
• Distributors - PICAXE
• Introducing the PICAXE System