Punched tape

Five-hole and eight-hole punched paper tape
Paper tape reader on an early computer with a small piece of five-hole tape connected in a circle - creating a physical program loop

Punched tape or perforated paper tape is a form of data storage, consisting of a long strip of paper in which holes are punched to store data. Now effectively obsolete, it was widely used during much of the twentieth century for teleprinter communication, for input to computers of the 1950s and 1960s, and later as a storage medium for minicomputers and CNC machine tools.

Origin

A paper tape, constructed from punched cards, in use in a Jacquard loom. The large holes on each edge are sprocket holes, used to pull the paper tape through the loom.

Paper tapes constructed from punched cards were widely used throughout the 19th century for controlling looms. Perforated paper tapes were first used by Basile Bouchon in 1725 to control looms. However, the paper tapes were expensive to create, fragile, and difficult to repair. By 1801 Joseph Marie Jacquard had developed machines to create paper tapes by tying punched cards in a sequence. The resulting paper tape, also called a "chain of cards", was stronger and simpler both to create and to repair. (See Jacquard loom).

This led to the concept of communicating data not as a stream of individual cards, but one "continuous card", or a tape. Many professional embroidery operations still refer to those individuals who create the designs and machine patterns as "punchers", even though punched cards and paper tape were eventually phased out, after many years of use, in the 1990s.

In 1846, Alexander Bain used punched tape to send telegrams.

In 1880s, Tolbert Lanston invented a Monotype System, which consisted of a keyboard (typesetting machine) and a composition caster. The tape, punched with the keyboard, was later read by the caster, which produced lead type according to the combinations of holes in 0, one or more of 31 positions. The tape reader used compressed air, which passed through the holes and was directed into certain mechanisms of the caster. The system went into commercial use in 1897 and was in production well into 1970s, undergoing several changes along the way.

Tape formats

A 24-channel program tape for the Harvard Mark I

Data were represented by the presence or absence of a hole at a particular location. Tapes originally had five rows of holes for data. Later tapes had 6, 7 and 8 rows. An early electro-mechanical calculating machine, the Automatic Sequence Controlled Calculator or Harvard Mark I, used paper tape with 24 rows.[1] A row of narrower holes that were always punched served to feed the tape, originally using a wheel with radial teeth called a sprocket wheel. Later optical readers used the sprocket holes to generate timing pulses.

Text was encoded in several ways. The earliest standard character encoding was Baudot, which dates back to the nineteenth century and had 5 holes. The Baudot code was never used in teleprinters. Instead, modifications such as the Murray code (which added carriage return and line feed), Western Union code, International Telegraphic Alphabet #2 (ITA 2), and American Teletypewriter code (USTTY), were used.[2] Other standards, such as Teletypesetter (TTS), Fieldata and Flexowriter, had 6 holes. In the early 1960s, the American Standards Association led a project to develop a universal code for data processing, which became known as ASCII. This 7-level code was adopted by some teleprinter users, including AT&T (Teletype). Others, such as Telex, stayed with the earlier codes.

Dimensions

Tape for punching was 0.00394 inches (0.1 mm) thick. The two most common widths were 11/16 inch (17.46 mm) for five bit codes, and 1 inch (25.4 mm) for tapes with six or more bits. Hole spacing was 0.1 inch (2.54 mm) in both directions. Data holes were 0.072 inches (1.83 mm) in diameter; feed holes were 0.046 inches (1.17 mm).[3] Paper tape rolls in both widths are still commercially available as of 2012.[4]

Chadless Tape

Most tape-punching equipment used solid punches to create holes in the tape. This process inevitably created "chad", or small circular pieces of paper. Managing the disposal of chad was an annoying and complex problem, as the tiny paper pieces had a tendency to escape and interfere with the other electromechanical parts of the teleprinter equipment.

Chadless paper tape
Chadless 5-level Baudot paper tape circa ~1975-1980 punched at Teletype Corp.

A variation on the tape punch was a device called a Chadless Printing Reperforator. This machine would punch a received teleprinter signal into tape and print the message on it at the same time, using a printing mechanism similar to that of an ordinary page printer. The tape punch, rather than punching out the usual round holes, would instead punch little U-shaped cuts in the paper, so that no chad would be produced; the "hole" was still filled with a little paper trap-door. By not fully punching out the hole, the printing on the paper remained intact and legible. This enabled operators to read the tape without having to decipher the holes, which would facilitate relaying the message on to another station in the network. Also, of course, there was no "chad box" to empty from time to time. A disadvantage to this mechanism was that chadless tape, once punched, did not roll up well, because the protruding flaps of paper would catch on the next layer of tape, so it could not be rolled up tightly. Another disadvantage, as seen over time, was that there was no reliable way to read chadless tape by optical means employed by later high-speed readers. However, the mechanical tape readers used in most standard-speed equipment had no problem with chadless tape, because it sensed the holes by means of blunt spring-loaded sensing pins, which easily pushed the paper flaps out of the way.

The word "Wikipedia", and a CRLF as 7-bit ASCII (without a parity bit)

Applications

Communications

Paper tape relay operation at US FAA's Honolulu flight service station in 1964

Punched tape was used as a way of storing messages for teletypewriters. Operators typed in the message to the paper tape, and then sent the message at the maximum line speed from the tape. This permitted the operator to prepare the message "off-line" at the operator's best typing speed, and permitted the operator to correct any error prior to transmission. An experienced operator could prepare a message at 135WPM (words per minute) or more for short periods.

The line typically operated at 75WPM, but it operated continuously. By preparing the tape "off-line" and then sending the message with a tape reader, the line could operate continuously rather than depending on continuous "on-line" typing by a single operator. Typically, a single 75WPM line supported three or more teletype operators working offline. Tapes punched at the receiving end could be used to relay messages to another station. Large store and forward networks were developed using these techniques.

Paper tape could be read into computers at up to 1000 characters per second.[5] The Danish company Regnecentralen has developed a paper tape reader called RC 2000 that could read 2000 characters per second. It was introduced in 1963. Later they increased the speed further, up to 2500 cps. As early as World War II, the Heath Robinson tape reader, used by Allied codebreakers, was capable of 2000 cps.

Minicomputers

Software on fanfold paper tape for the Data General Nova minicomputer.

When the first minicomputers were being released, most manufacturers turned to the existing mass-produced ASCII teleprinters (primarily the Teletype Model 33, capable of 10 ASCII characters per second throughput) as a low-cost solution for keyboard input and printer output. The commonly specified Model 33 ASR included a paper tape punch/reader, where ASR stands for "Automatic Send/Receive" as opposed to the punchless/readerless KSR - Keyboard Send/Receive and RO - Receive Only models. As a side effect, punched tape became a popular medium for low cost minicomputer data and program storage, and it was common to find a selection of tapes containing useful programs in most minicomputer installations. Faster optical readers were also common.

Binary data transfer to or from these minicomputers was often accomplished using a doubly encoded technique to compensate for the relatively high error rate of punches / readers. The low-level encoding was typically ASCII, further encoded and framed in various schemes such as Intel Hex - in which a binary value of "01011010" would be represented by the ASCII characters "5A". Framing, addressing and checksum (primarily in ASCII hex characters) information provided error detection capabilities. Efficiencies of such an encoding scheme are on the order of 35-40% (e.g., 36% from 44 8-bit ASCII characters being needed to represent 16 bytes of binary data per frame).

Data transfer for ROM and EPROM programming

In the 1970s through the early 1980s, paper tape was commonly used to transfer binary data for incorporation in either mask-programmable read-only memory (ROM) chips or their erasable counterparts - EPROMs. A significant variety of encoding formats were developed for use in computer and ROM/EPROM data transfer.[6] Encoding formats commonly used were primarily driven by those formats that EPROM programming devices supported and included various ASCII hex variants as well as a number of computer-proprietary formats.

A much more primitive as well as a much longer high-level encoding scheme was also used - BNPF (Begin-Negative-Positive-Finish). In BNPF encoding, a single byte (8 bits) would be represented by a highly redundant character framing sequence starting with a single ASCII "B", eight ASCII characters where a "0" would be represented by a "N" and a "1" would be represented by a "P", followed by an ending ASCII "F". These ten-character ASCII sequences were separated by one or more whitespace characters, therefore using at least 11 ASCII characters for each byte stored (9% efficiency). The ASCII "N" and "P" characters differ in four bit positions, providing excellent protection from single punch errors. Alternative schemes were also available where "H" and "L" or "0" and "1" were also available to represent data bits, but in both of these encoding schemes, the two data-bearing ASCII characters differ in only one bit position, providing very poor single punch error detection.

Cash registers

National Cash Register or NCR (Dayton Ohio) made cash registers around 1970 that would punch paper tape. The tape could then be read into a computer and not only could sales information be summarized, billings could be done on charge transactions.

Newspaper industry

Punched paper tape was used by the newspaper industry until the mid-1970s or later. Newspapers were typically set in hot lead by devices such as a linotype. With the wire services coming into a device that would punch paper tape, rather than the linotype operator having to retype all the incoming wire stories, the paper tape could be put into a paper tape reader on the linotype and it would create the lead slugs without the operator re-typing the stories. This also allowed newspapers to use devices, such as the Friden Flexowriter, to convert typing to lead type via tape. Even after the demise of the Linotype/hot lead, many early "offset" devices had paper tape readers on them to produce the news-story copy.

Automated machinery

Paper tape reader on a computer numerical control (CNC) machine.

In the 1970s, computer-aided manufacturing equipment often used paper tape. Paper tape was a very important storage medium for computer-controlled wire-wrap machines, for example. A paper tape reader was smaller and much less expensive than hollerith card or magnetic tape readers. Premium black waxed and lubricated long-fiber papers, and Mylar film tape were invented so that production tapes for these machines would last longer.

Cryptography

Paper tape was the basis of the Vernam cipher, invented in 1917. During the last third of the 20th century, the National Security Agency used punched paper tape to distribute cryptographic keys. The 8-level paper tapes were distributed under strict accounting controls and were read by a fill device, such as the hand held KOI-18, that was temporarily connected to each security device that needed new keys. NSA has been trying to replace this method with a more secure electronic key management system (EKMS), but paper tape is apparently still being employed.

Fanfold paper tape.

Paper tape canister

Paper tape canister, designed to securely distribute cryptographic keys

The paper tape canister is a tamper resistant container from which the contents may manually be dispensed but which prohibits reinsertion of a tape once removed. It was used to securely distribute cryptographic keys. Distributing cryptographic keys in the open left the keys vulnerable. "Putting tape in canisters solved a lot of the security problem by narrowing the vulnerability to the point of use rather than the whole time in inventory", said Whitfield Diffie. The canister was invented to prevent the ability to tamper with the paper tape once placed inside the canister. One of the primary users of the Paper Tape Canister was the National Security Agency. The NSA needed the ability to transfer crytographic keys in a way that clearly showed if the keys had been compromised.

This paper tape canister has clearly been tampered with. The paper tape has been withdrawn from the canister and an attempt to reinsert the tape has failed. Any data stored on the tape been disrupted; and could be misrepresented or exploited.

The paper tape canister has several tamper-proof design features:

Hugh V. Hayes, the inventor, wrote

Every paper tape canister is unique. This uniqueness is accomplished during the manufacturing process, the plastic flowing into the mold creates unique flow patterns throughout the entire paper tape canister thereby making it impossible to duplicate eliminating the possibility of substitution.

The welded seam ensures that the paper tape canister cannot be pried open without being detected.

Is a unique seam that is difficult to duplicate.

The paper path will not allow the reinsertion of tape.


Limitations

The three biggest problems with paper tape were:

Advantages

Punched tape does have some useful properties:

Punched tape in art

A computing or telecommunications professional depicted in the Monument to the Conquerors of Space in Moscow (1964) holds what appears to be a punched tape with three rows of rectangular holes.

Current use

Use of punched tape today is very rare. It may still be used in older military systems and by some hobbyists. In CNC machining applications, what few existing installations remained in grandfathered use are now quickly disappearing as the advantages for new orders of old part designs are being superseded by natural economic evolution. However, some modern CNC systems still measure the size of stored CNC programs in feet or meters, corresponding to the equivalent length if punched on paper tape.[8]

See also

References

  1. Dalakov, Georgi, History of computers: The MARK computers of Howard Aiken, retrieved 2011-01-12
  2. Proesch, Roland (2009). Technical Handbook for Radio Monitoring HF: Edition 2009. Books on Demand. ISBN 3837045730.
  3. ECMA 10, Standard for Data Interchange on Punched Tape, November 1965
  4. http://www.wncsupply.com/paper-tape-rolls.html
  5. Hult, Ture (1963), "Presentation of a new high speed paper tape reader", BIT Numerical Mathematics 3 (2): 93–96, doi:10.1007/BF01935575
  6. "Translation File Formats" (PDF). Data I/O Corporation. Retrieved 2010-08-30.
  7. Sinha, Naresh Kumar. Microprocessor-based Control Systems. p. 264. Paper tape is well suited to a machine shop environment whereas magnetic tape may be accidentally erased or contaminated by foreign substances. ... Other disadvantages of paper tape are as follows ...
  8. CNC Control Setup for Milling and Turning: Mastering CNC Control Systems, By Peter Smid, 2010, p. 20

External links

Wikimedia Commons has media related to Papertape.
This article is issued from Wikipedia - version of the Friday, April 29, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.