Pinch (plasma physics)

For other uses, see Pinch (disambiguation).
Lightning bolts illustrating electromagnetically pinched plasma filaments
A 1905 study of pinches, where electric lightning was used to create a Z-pinch inside a metal tube.[1]

A pinch is the compression of an electrically conducting filament by magnetic forces. The conductor is usually a plasma, but could also be a solid or liquid metal. Pinches were the first device used by mankind for controlled nuclear fusion.[2]

The phenomenon may also be referred to as a Bennett pinch[3] (after Willard Harrison Bennett), electromagnetic pinch,[4] magnetic pinch,[5] pinch effect[6] or plasma pinch.[7]

Pinches occur naturally in electrical discharges such as lightning bolts,[8] the aurora,[9] current sheets,[10] and solar flares.[11]

Basic mechanism

This is a basic explanation of how a pinch works. (1) Pinches apply a huge voltage across a tube. This tube is filled with fusion fuel, typically deuterium gas. If the voltage times the charge is higher than the ionization energy of the gas the gas ionizes. (2) Current jumps across this gap. (3) The current makes a magnetic field which is perpendicular to the current. This magnetic field pulls the material together. (4) These atoms can get close enough to fuse.

Types

An example of a man-made pinch. Here Z-pinches constrain the plasma inside filaments of electrical discharge from a Tesla coil
The MagLIF concept, a combination of a Z-pinch and a laser beam

Pinches exist in laboratories and in nature. Pinches differ in their geometry and operating forces.[12] These include:

Uncontrolled
Any time an electric current moves in large amounts (e.g., lightning, arcs, sparks, discharges) a magnetic force can pull together plasma. This can be insufficient for fusion.
Sheet pinch
An astrophysical effect, this arises from vast sheets of charge particles.[13]
Z-pinch
The current runs down the axis (or walls) of the cylinder while the magnetic field is azimuthal
Theta pinch
The magnetic field runs down the axis of the cylinder, while the electric field is in the azimuthal direction (also called a thetatron[14])
Screw pinch
A combination of a Z pinch and theta pinch [15] (also called a stabilized Z-pinch, or θ-Z pinch)[16][17]
Reversed field pinch
This is an attempt to do a Z-pinch inside an endless loop. The plasma has an internal magnetic field. As you move out from the center of this ring, the magnetic field reverses direction. Also called a toroidal pinch.
Inverse pinch
An early fusion concept, this device consisted of a rod surrounded by plasma. Current traveled through the plasma and returned along the center rod.[18] This geometry was slightly different than a z-pinch in that the conductor was in the center, not the sides.
Cylindrical pinch
Orthogonal pinch effect
Ware pinch
A pinch that happens inside Tokamaks. This is when particles inside the Banana orbit condense together.[19][20]
MAGLIF
This is a combination of a Z-pinch and a laser beam to stop loss of material at the end.[21]

Common behavior

Pinches may become unstable.[22] They radiate energy as light across the whole electromagnetic spectrum including radio waves, x-rays,[23] gamma rays,[24] synchrotron radiation,[25] and visible light. They also produce neutrons, as a product of fusion.[26]

Applications and devices

Pinches are used to generate X-rays and the intense magnetic fields generated are used in electromagnetic forming of metals. They also have applications in particle beams[27] including particle beam weapons,[28] astrophysics studies[29] and it has been proposed to use them in space propulsion.[30] A number of large pinch machines have been built to study fusion power; here are several:

Crushing cans with the pinch effect

Pinched aluminium can, produced from a pulsed magnetic field created by rapidly discharging 2 kilojoules from a high voltage capacitor bank into a 3-turn coil of heavy gauge wire.

Many high-voltage electronics enthusiasts make their own crude electromagnetic forming devices.[32][33][34] They use pulsed power techniques to produce a theta pinch capable of crushing an aluminium soft drink can using the Lorentz forces created when large currents are induced in the can by the strong magnetic field of the primary coil.[35][36]

An electromagnetic aluminium can crusher consists of four main components: a high voltage DC power supply, which provides a source of electrical energy, a large energy discharge capacitor to accumulate the electrical energy, a high voltage switch or spark gap, and a robust coil (capable of surviving high magnetic pressure) through which the stored electrical energy can be quickly discharged in order to generate a correspondingly strong pinching magnetic field (see diagram below).

Electromagnetic pinch "can crusher": schematic diagram

In practice, such a device is somewhat more sophisticated than the schematic diagram suggests, including electrical components that control the current in order to maximize the resulting pinch, and to ensure that the device works safely. For more details, see the notes.[37]

History

The Institute of Electrical and Electronics Engineers emblem shows the basic features of an azimuthal magnetic pinch.[38]

The first creation of a Z-pinch in the laboratory may have occurred in 1790 in Holland when Martinus van Marum created an explosion by discharging 100 Leyden jars into a wire.[39] The phenomenon was not understood until 1905, when Pollock and Barraclough[1] investigated a compressed and distorted length of copper tube from a lightning rod after it had been struck by lightning. Their analysis showed that the forces due to the interaction of the large current flow with its own magnetic field could have caused the compression and distortion.[40] A similar, and apparently independent, theoretical analysis of the pinch effect in liquid metals was published by Northrupp in 1907.[41] The next major development was the publication in 1934 of an analysis of the radial pressure balance in a static Z-pinch by Bennett[42] (see the following section for details).

Thereafter, the experimental and theoretical progress on pinches was driven by fusion power research. In their article on the "Wire-array Z-pinch: a powerful x-ray source for ICF", M G Haines et al., wrote on the "Early history of Z-pinches".[43]

In 1946 Thompson and Blackman submitted a patent for a fusion reactor based on a toroidal Z-pinch[44] with an additional vertical magnetic field. But in 1954 Kruskal and Schwarzschild[45] published their theory of MHD instabilities in a Z-pinch. In 1956 Kurchatov gave his famous Harwell lecture showing nonthermal neutrons and the presence of m = 0 and m = 1 instabilities in a deuterium pinch.[46] In 1957 Pease[47] and Braginskii[48][49] independently predicted radiative collapse in a Z-pinch under pressure balance when in hydrogen the current exceeds 1.4 MA. (The viscous rather than resistive dissipation of magnetic energy discussed above and in[50] would however prevent radiative collapse). In 1958, the world's first controlled fusion experiment was accomplished using a Z-pinch machine named Scylla I at the Los Alamos National Laboratory. A cylinder full of deuterium was converted into a plasma and compressed to 15 million degrees Celsius under a Z-pinch effect.[2] Lastly, at Imperial College in 1960, led by R Latham, the Plateau-Rayleigh instability was shown, and its growth rate measured in a dynamic Z-pinch.[51]

Equilibrium analysis

One dimension

In plasma physics three pinch geometries are commonly studied: the θ-pinch, the Z-pinch, and the Screw Pinch. These are cylindrically shaped. The cylinder is symmetric in the axial (z) direction and the azimuthal (θ) directions. The one-dimensional pinches are named for the direction the current travels.

The θ-pinch

A sketch of the θ-pinch equilibrium. The      z-directed magnetic field corresponds to a      θ-directed plasma current.

The θ-pinch has a magnetic field traveling in the z direction. Using Ampère's law (discarding the displacement term)

\begin{align}
        \vec{B} &= B_z(r)\hat{z} \\
  \mu_0 \vec{J} &= \nabla \times \vec{B} \\
                &= \frac{1}{r} \frac{d}{d \theta}B_z(r) \hat{r} - \frac{d}{dr}B_z(r) \hat{\theta}
\end{align}

Since B is only a function of r we can simplify this to

 \mu_0 \vec{J} = -\frac{d}{dr}B_z(r) \hat{\theta}

So J points in the θ direction.

Thus, the equilibrium condition (∇p = j × Β) for the θ-pinch reads:

 \frac{d}{d r} \left( p + \frac{B_z^2}{2\mu_0} \right) = 0

θ-pinches tend to be resistant to plasma instabilities; This is due in part to Alfvén's Theorem (or, frozen in flux theorem).

The Z-pinch

A sketch of the Z-pinch equilibrium. A      θ-directed magnetic field corresponds to a      z-directed plasma current.

The Z-pinch has a magnetic field in the θ direction. Again, by electrostatic Ampère's Law

\begin{align}
        \vec{B} &= B_{\theta}(r)\hat{\theta} \\
  \mu_0 \vec{J} &= \nabla \times \vec{B} \\
                &= \frac{1}{r}\frac{d}{dr}\left(r B_\theta(r)\right) \hat{z} - \frac{d}{dz}B_\theta(r) \hat{r} \\
                &= \frac{1}{r}\frac{d}{dr}\left(r B_\theta(r)\right) \hat{z}
\end{align}

So J points in the z direction.

Thus, the equilibrium condition, ∇p = j × Β, for the Z-pinch reads:

 \frac{d}{d r} \left( p + \frac{B_\theta^2}{2\mu_0} \right) + \frac{B_\theta^2}{\mu_0 r} = 0

Since particles in a plasma basically follow magnetic field lines, Z-pinches lead them around in circles. Therefore, they tend to have excellent confinement properties.

The screw pinch

The screw pinch is an effort to combine the stability aspects of the θ-pinch and the confinement aspects of the Z-pinch. Referring once again to Ampère's Law

\nabla \times \vec{B} = \mu_0 \vec{J}

But this time, the B field has a θ component and a z component

\begin{align}
        \vec{B} &= B_\theta \hat{\theta} + B_z \hat{z} \\
  \mu_0 \vec{J} &= \frac{1}{r}\frac{d}{dr}\left(r B_\theta\right) \hat{z} - \frac{d}{dr}B_z \hat{\theta}
\end{align}

So this time J has a component in the z direction and a component in the θ direction.

Finally, the equilibrium condition (∇p = j × Β) for the screw pinch reads:

 \frac{d}{d r} \left(p + \frac{B_z^2 + B_\theta^2}{2 \mu_0} \right) + \frac{B_\theta^2}{\mu_0 r} = 0

The screw pinch via colliding optical vortices

The screw pinch might be produced in laser plasma by colliding optical vortices of ultrashort duration.[52] For this purpose optical vortices ought to be phase-conjugated.[53] The magnetic field distribution is given here again via Ampère's law:

\nabla \times \vec{B} = \mu_0 \vec{J}

Two dimensions

A toroidal coordinate system in common use in plasma physics.
  The red arrow indicates the poloidal direction (θ)
  The blue arrow indicates the toroidal direction (φ)

A common problem with one-dimensional pinches is the end losses. Most of the motion of particles is along the magnetic field. With the θ-pinch and the screw-pinch, this leads particles out of the end of the machine very quickly, leading to a loss of mass and energy. On top of this problem, the Z-pinch has major stability problems. Though particles can be reflected to some extent with magnetic mirrors, even these allow many particles to pass. A common method of beating these end losses, is to bend the cylinder around into a torus. Unfortunately this breaks θ symmetry, as paths on the inner portion (inboard side) of the torus are shorter than similar paths on the outer portion (outboard side). Thus, a new theory is needed. This gives rise to the famous Grad–Shafranov equation. Numerical solutions to the Grad–Shafranov equation have also yielded some equilibria, most notably that of the reversed field pinch.

Three dimensions

As of 2015, there is not a coherent analytical theory for three-dimensional equilibria. The general approach to finding three-dimensional equilibria is to solve the vacuum ideal MHD equations. Numerical solutions have yielded designs for stellarators. Some machines take advantage of simplification techniques such as helical symmetry (for example University of Wisconsin's Helically Symmetric eXperiment). However, for an arbitrary three-dimensional configuration an equilibrium relation, similar to that of the 1-D configurations exists:[54]

 \nabla_\perp \left( p + \frac{B^2}{2 \mu_0} \right) - \frac{B^2}{\mu_0 }\vec{\kappa} = 0

Where κ is the curvature vector defined as:

 \vec{\kappa} = \left(\vec{b} \cdot \nabla\right)\vec{b}

with b the unit vector tangent to B.

Formal treatment

A stream of water pinching into droplets has been suggested as an analogy to the electromagnetic pinch.[55] The gravity accelerates free-falling water which causes the water column to constrict. Then surface tension breaks the narrowing water column into droplets (not shown here) (see Plateau-Rayleigh instability), which is analogous to the magnetic field which has been suggested as the cause of pinching in bead lightning.[56] The morphology (shape) is similar to the so-called sausage instability in plasma.

The Bennett relation

Consider a cylindrical column of fully ionized quasineutral plasma, with an axial electric field, producing an axial current density, j, and associated azimuthal magnetic field, B. As the current flows through its own magnetic field, a pinch is generated with an inward radial force density of j x B. In a steady state with forces balancing:

p = ∇(pe + pi) = j × Β

where ∇p is the magnetic pressure gradient, pe and pi is the electron and ion pressures. Then using Maxwell's equation× B = μ0 j and the ideal gas law p = N k T, we derive:

2 N k(T_e + T_i) = \frac{{\mu_0}} {4 \pi} I^2 (the Bennett relation)

where N is the number of electrons per unit length along the axis, Te and Ti are the electron and ion temperatures, I is the total beam current, and k is the Boltzmann constant.

The generalized Bennett relation

The generalized Bennett relation considers a current-carrying magnetic-field-aligned cylindrical plasma pinch undergoing rotation at angular frequency ω

The Generalized Bennett Relation considers a current-carrying magnetic-field-aligned cylindrical plasma pinch undergoing rotation at angular frequency ω. Along the axis of the plasma cylinder flows a current density jz, resulting in an azimuthal magnetίc field Βφ. Originally derived by Witalis,[57] the Generalized Bennett Relation results in:[58]

\begin{align}
  \frac{1}{4} \frac{\partial^2 J_0}{\partial t^2} = {} &W_{\perp \text{kin}} + \Delta W_{E_z} + \Delta W_{B_z} + \Delta W_k - \frac{{\mu_0}} {8 \pi} I^2 (a) \\[8pt]
                                                       & {} - \frac{1}{2}G\overline{m}^2 N^2 (a) + \frac{1}{2}\pi a^2 \epsilon_0 \left(E_r^2 (a) - E_\phi^2 (a)  \right)\\
\end{align}

The positive terms in the equation are expansional forces while the negative terms represent beam compressional forces.

The Carlqvist relation

The Carlqvist Relation, published by Per Carlqvist in 1988,[12] is a specialization of the Generalized Bennett Relation (above), for the case that the kinetic pressure is much smaller at the border of the pinch than in the inner parts. It takes the form

\frac{{\mu_0}} {8 \pi} I^2 (a) +\frac{1}{2}G\overline{m}^2 N^2 (a) =  \Delta W_{B_z} + \Delta W_k

and is applicable to many space plasmas.

The Bennett pinch showing the total current (I) versus the number of particles per unit length (N). The chart illustrates four physically distinct regions. The plasma temperature is 20 K, the mean particle mass 3×10−27 kg, and ΔWBz is the excess magnetic energy per unit length due to the axial magnetic field Bz. The plasma is assumed to be non-rotational, and the kinetic pressure at the edges is much smaller than inside.

The Carlqvist Relation can be illustrated (see right), showing the total current (I) versus the number of particles per unit length (N) in a Bennett pinch. The chart illustrates four physically distinct regions. The plasma temperature is quite cold (Ti = Te = Tn = 20 K), containing mainly hydrogen with a mean particle mass 3×10−27 kg. The thermokinetic energy Wk >> πa2 pk(a). The curves, ΔWBz show different amounts of excess magnetic energy per unit length due to the axial magnetic field Bz. The plasma is assumed to be non-rotational, and the kinetic pressure at the edges is much smaller than inside.

Chart regions: (a) In the top-left region, the pinching force dominates. (b) Towards the bottom, outward kinetic pressures balance inwards magnetic pressure, and the total pressure is constant. (c) To the right of the vertical line ΔWBz = 0, the magnetic pressures balances the gravitational pressure, and the pinching force is negligible. (d) To the left of the sloping curve ΔWBz = 0, the gravitational force is negligible. Note that the chart shows a special case of the Carlqvist relation, and if it is replaced by the more general Bennett relation, then the designated regions of the chart are not valid.

Carlqvist further notes that by using the relations above, and a derivative, it is possible to describe the Bennett pinch, the Jeans criterion (for gravitational instability,[59] in one and two dimensions), force-free magnetic fields, gravitationally balanced magnetic pressures, and continuous transitions between these states.

References in culture

A fictionalized pinch-generating device was used in Ocean's Eleven, where it was used to disrupt Las Vegas's power grid just long enough for the characters to begin their heist.[60]

See also

References

  1. 1 2 Pollock J A and Barraclough S (1905) Proc. R. Soc. New South Wales 39 131
  2. 1 2 Phillips, James. "Magnetic Fusion." Los Alamos Science Winter 1983: 64-67. Web. 4 Apr. 2013.
  3. See for example, Buneman, O., "The Bennett Pinch" (1961) Plasma Physics, Edited by James E. Drummond. LOC 60-12766. Publ. McGraw-Hill, Inc., New York, 1961, p.202
  4. Lee, S (1983). "Energy balance and the radius of electromagnetically pinched plasma columns". Plasma Physics 25 (5): 571–576. Bibcode:1983PlPh...25..571L. doi:10.1088/0032-1028/25/5/009.
  5. Schmidt, Helmut (1966). "Formation of a Magnetic Pinch in InSb and the Possibility of Population Inversion in the Pinch". Physical Review 149 (2): 564–573. Bibcode:1966PhRv..149..564S. doi:10.1103/physrev.149.564.
  6. Severnyi, A. B. (1959). "On the Appearance of Cosmics Rays in the Pinch Effect in Solar Flares". Soviet Astronomy 3: 887. Bibcode:1959SvA.....3..887S.
  7. Zueva, N. M.; Solov'ev, L. S.; Morozov, A. I. (1976). "Nonlinear instability of plasma pinches". Journal of Experimental and Theoretical Physics Letters 23: 256. Bibcode:1976JETPL..23..256Z.
  8. Rai, J.; Singh, A. K.; Saha, S. K (1973). "Magnetic field within the return stroke channel of lightning". Indian Journal of Radio and Space Physics 2: 240–242. Bibcode:1973IJRSP...2..240R.
  9. Galperin, Iu. I.; Zelenyi, L. M.; Kuznetsova, M. M. (1986). "Pinching of field-aligned currents as a possible mechanism for the formation of raylike auroral forms". Kosmicheskie Issledovaniia 24: 865–874. Bibcode:1986CosRe..24..865G.
  10. Syrovatskii, S. I. (1981). "Pinch sheets and reconnection in astrophysics". Annual Review of Astronomy and Astrophysics 19: 163–229. Bibcode:1981ARA&A..19..163S. doi:10.1146/annurev.aa.19.090181.001115.
  11. Airapetyan, V. S.; Vikhrev, V. V.; Ivanov, V. V.; Rozanova, G. A. (1990). "Pinch Mechanism of Energy Release of Stellar Flares". Astrophysics 32 (3): 230–235. Bibcode:1990Ap.....32..230A. doi:10.1007/bf01005504.
  12. 1 2 Carlqvist, Per, (1988) "Cosmic electric currents and the generalized Bennett relation" Astrophysics and Space Science vol. 144, no. 1-2, May 1988, p. 73-84
  13. Biskamp, Dieter (1997) Nonlinear Magnetohydrodynamics Cambridge University Press, Cambridge, England, page 130, ISBN 0-521-59918-0
  14. See Dictionary of Material Science and High Energy Physics p.315 ISBN 0-8493-2889-6
  15. Srivastava, K. M.; Vyas, D. N., (1982) "Non-linear analysis of the stability of the screw pinch" Astrophysics and Space Science, vol. 86, no. 1, Aug. 1982, p. 71-89
  16. See "MHD Equilibria" in Introduction to Plasma Physics by I.H.Hutchinson (2001)
  17. Srivastava, K. M.; Waelbroeck, F. (1976). "On the stability of the screw pinch in the CGL model". Journal of Plasma Physics 16: 261. Bibcode:1976JPlPh..16..261S. doi:10.1017/s0022377800020201.
  18. "Inverse Pinch Effect" Anderson, Et al. Physics of Fluids, Volume 1, Issue 6, p.489-494
  19. Helander, P.; et al. (2005). "The effect of non-inductive current drive on tokamak transport". Plasma Physics and Controlled Fusion 47 (12B): B151–B163. Bibcode:2005PPCF...47B.151H. doi:10.1088/0741-3335/47/12b/s12.
  20. "Plasma Physics: Third Edition" Page 266 https://books.google.co.uk/books?id=4cHkd77TSHcC&pg=PA266&dq=Ware+pinch&hl=en&sa=X&ei=aZsVVdvZF5L8gwSO_oDoDw&ved=0CCYQ6AEwAQ#v=onepage&q=Ware%20pinch&f=false
  21. Slutz, Stephen; Vesey, Roger A. (2012). "High-Gain Magnetized Inertial Fusion". Physical Review Letters 108 (2). Bibcode:2012PhRvL.108b5003S. doi:10.1103/PhysRevLett.108.025003.
  22. Hardee, P. E. (1982). "Helical and pinching instability of supersonic expanding jets in extragalactic radio sources". Astrophysical Journal 257: 509–526. Bibcode:1982ApJ...257..509H. doi:10.1086/160008.
  23. Pereira, N. R.; et al. (1988). "[X rays from Z-pinches on relativistic electron-beam generators]". Journal of Applied Physics 64: R1–R27. doi:10.1063/1.341808.
  24. Wu, Mei; Chen, Li; Li, Ti-Pei (2005). "Polarization in Gamma-Ray Bursts Produced by Pinch Discharge". Chinese Journal of Astronomy & Astrophysics 5: 57–64. Bibcode:2005ChJAA...5...57W. doi:10.1088/1009-9271/5/1/007.
  25. Peratt, A.L., "Synchrotron radiation from pinched particle beams", (1998) Plasma Physics: VII Lawpp 97: Proceedings of the 1997 Latin American Workshop on Plasma Physics, Edited by Pablo Martin, Julio Puerta, Pablo Martmn, with reference to Meierovich, B. E., "Electromagnetic collapse. Problems of stability, emission of radiation and evolution of a dense pinch" (1984) Physics Reports, Volume 104, Issue 5, p. 259-346.
  26. Anderson, Oscar A.; et al. (1958). "Neutron Production in Linear Deuterium Pinches". Physical Review 110 (6): 1375–1387. Bibcode:1958PhRv..110.1375A. doi:10.1103/physrev.110.1375.
  27. Ryutov, D. D.; Derzon, M. S.; Matzen, M. K (2000). "The physics of fast Z pinches". Reviews of Modern Physics 72 (1): 167–223. Bibcode:2000RvMP...72..167R. doi:10.1103/revmodphys.72.167.
  28. Andre Gsponer, "Physics of high-intensity high-energy particle beam propagation in open air and outer-space plasmas" (2004) http://arxiv.org/abs/physics/0409157
  29. Peratt, Anthony L., "The role of particle beams and electrical currents in the plasma universe" (1988) Laser and Particle Beams (ISSN 0263-0346), vol. 6, Aug. 1988, p. 471-491.
  30. "Z-Pinch Pulsed Plasma Propulsion Technology Development"Final Report Advanced Concepts Office (ED04) Marshall Space Flight Center October 8, 2010, Tara Polsgrove, Et Al.
  31. http://dorland.pp.ph.ic.ac.uk/magpie/?page_id=239 "Wire Arrays Z-Pinch" accessed: 3-27-2015
  32. LaPointe, Robert. "High Voltage Devices and Experiments". Retrieved February 21, 2013.
  33. Tristan. "Electromagnetic Can Crusher". Retrieved February 21, 2013.
  34. Borros, Sam. "Solid State Can Crusher". Retrieved February 21, 2013.
  35. "MagnetoPulS". web site. MAGNET-PHYSIK Dr. Steingroever GmbH. 2002. Archived from the original on 2003-05-22. Retrieved February 21, 2013.
  36. "Industrial Application of the Electromagnetic Pulse Technology" (PDF). white paper. PSTproducts GmbH. June 2009. Retrieved February 21, 2013.
  37. Examples of electromagnetic pinch can crushers can be found at (a) Bob LaPointe's site on High Voltage Devices and Experiments (b) Tristran's Electromagnetic Can Crusher (including schematic) (c) Sam Borros's Solid State Can Crusher
  38. See also the IEEE History Center, "Evolution of the IEEE Logo" March 1963; see also the comments in "Laboratory Astrophysics"
  39. van Marum M 1790 Proc. 4th Int. Conf. on Dense Z-Pinches (Vancouver 1997) (Am. Inst. Phys. Woodbury, New York, 1997) Frontispiece and p ii
  40. R. S. Pease, "The Electromagnetic Pinch: From Pollock to the Joint European Torus", "Pollock Memorial Lecture for 1984 delivered at the University of Sydney, 28 November, 1984": This review of the electromagnetic pinch starts with an exhibit taken from Pollock's work, carefully preserved and drawn to attention of modern research by Professor C. Watson-Munro. It is a compressed and distorted length of copper tube originally part of the lightning conductor on the Hartley Vale kerosene refinery in New South Wales. It was known to have been struck by lightning. Pollock and Barraclough (1905) from the Department of Mechanical Engineering at Sydney University carried out an analysis to see whether or not the compression could have arisen from the flow of electric current. They concluded that the compressive forces, due to the interaction of the large current flow with its own magnetic field could have been responsible for the compression and distortion. As far as I know, this is the first identified piece of observational data on the electromagnetic pinch; and the first theoretical discussion of the effect.
  41. Northrupp E F 1907 "Some Newly Observed Manifestations of Forces in the Interior of an Electric Conductor" Phys. Rev. 24 474. He wrote: "Some months ago, my friend, Carl Hering, described to me a surprising and apparently new phenomenon which he had observed. He found, in passing a relatively large alternating current through a non-electrolytic, liquid conductor contained in a trough, that the liquid contracted in cross-section and flowed up hill lengthwise of the trough... Mr. Hering suggested the idea that this contraction was probably due to the elastic action of the lines of magnetic force which encircle the conductor... As the action of the forces on the conductor is to squeeze or pinch it, he jocosely called it the 'pinch phenomenon'.
  42. "Magnetically Self-Focussing Streams". Phys. Rev 45: 890–897. 1934. Bibcode:1934PhRv...45..890B. doi:10.1103/physrev.45.890.
  43. Haines, M G; Sanford, T W L; Smirnov, V P (2005). "Wire-array Z-pinch: a powerful x-ray source for ICF". Plasma Phys. Control. Fusion 47: B1–B11. doi:10.1088/0741-3335/47/12b/s01.
  44. Thompson, G P; Blackman; Haines, M G (1996). "Historical Perspective: Fifty years of controlled fusion research". Plasma Phys. Control. Fusion 38: 643. Bibcode:1996PPCF...38..643H.
  45. Kruskal, M D; Schwarzschild (1954). "Some Instabilities of a Completely Ionized Plasma". Proc. R. Soc. Lond A 223: 348–360. Bibcode:1954RSPSA.223..348K. doi:10.1098/rspa.1954.0120.
  46. Kurchatov I V (1957) J. Nucl. Energy 4 193
  47. Pease, R S (1957). "Equilibrium Characteristics of a Pinched Gas Discharge Cooled by Bremsstrahlung Radiation". Proc. Phys. Soc. Lond 70: 11–23. Bibcode:1957PPSB...70...11P. doi:10.1088/0370-1301/70/1/304.
  48. Braginskii S I 1957 Zh. Eksp. Teor. Fiz 33 645
  49. Braginskii S I 1958 Sov. Phys.—JETP 6 494
  50. Haines M G et al. 2005 Phys. Rev. Lett. submitted; see also EPS Conf. on Plasma Physics 2004 (London, UK) paper 73
  51. Curzon, F L; et al. (1960). "Experiments on the Growth Rate of Surface Instabilities in a Linear Pinched Discharge". Proc. R. Soc. Lond A 257: 386–401. Bibcode:1960RSPSA.257..386C. doi:10.1098/rspa.1960.0158.
  52. A.Yu.Okulov. "Laser singular Theta-pinch", Phys.Lett.A, v.374, 4523-4527, (2010)
  53. Optical phase conjugation and electromagnetic momenta
  54. Ideal Magnetohydrodynamics: Modern perspectives in energy. Jeffrey P. Freidberg. Massachusetts Institute of Technology. Cambridge, Massachusetts. Plenum Press - New York and London - 1987. (Pg.86 & 95)
  55. Trubnikov, Boris A (1992). "A new hypothesis of cosmic ray generation in plasma pinches". IEEE Transactions on Plasma Science 20 (6): 898–904. Bibcode:1992ITPS...20..898T. doi:10.1109/27.199547.
  56. "The PLASMAK Configuration and Ball Lightning" (PDF) presented at the International Symposium on Ball Lightning; July 1988
  57. Witalis, E. A. "Plasma-physical aspects of charged-particle beams" (1981) Physical Review A - General Physics, 3rd Series, vol. 24, Nov. 1981, p. 27582764
  58. Anthony L . Peratt, "Physics of the Plasma Universe", 1992 Springer-Verlag, ISBN 0-387-97575-6
  59. Jeans, J. H. (1902). "The stability of a spherical nebula". Phil. Trans. R. Soc. Lond. A 199. Bibcode:1902RSPTA.199....1J.
  60. "The Con-Artist Physics of 'Ocean's Eleven'". American Physical Society. March 2002.

External links

This article is issued from Wikipedia - version of the Thursday, February 18, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.