Polymer brush

Sample polymer brush

Polymer brush is a layer of polymers attached with one end to a surface.^[1] The brushes may be either in a solvent state, when the dangling chains are submerged into a solvent, or in a melt state, when the dangling chains completely fill up the space available. Additionally, there is a separate class of polyelectrolyte brushes, when the polymer chains themselves carry an electrostatic charge.

The brushes are often characterized by the high density of grafted chains. The limited space then leads to a strong extension of the chains, and unusual properties of the system. Brushes can be used to stabilize colloids, reduce friction between surfaces, and to provide lubrication in artificial joints.^[2]

Polymer brushes have been modeled with Monte Carlo methods,^[3] Brownian dynamics simulations^[4] and molecular theories ^[5]

Structure of a polymer brush

Polymer molecule within a brush. The drawing shows the chain elongation decreasing from the attachment point and vanishing at free end. The "blobs", schematized as circles, represent the (local) length scale at which the statistics of the chain change from a 3D random walk (at smaller length scales) to a 2D in-plane random walk and a 1D normal directed walk (at larger length scales).

Polymer molecules within a brush are stretched away from the attachment surface as a result of the fact that they repel each other (steric repulsion or osmotic pressure). More precisely,^[6] they are more elongated near the attachment point and unstretched at the free end, as depicted on the drawing.

More preciseley, within the approximation derived by Milner, Witten, Cates,^[6] the average density of all monomers in a given chain is always the same up to a prefactor:

$\phi(z,\rho)=\frac{\partial n}{\partial z}$

$n(z,\rho)=\frac{2N}{\pi}\arcsin\left(\frac{z}{\rho}\right)$

where $\rho$ is the altitude of the end monomer and $N$ the number of monomers per chain.

The averaged density profile $\epsilon(\rho)$ of the end monomers of all attached chains, convoluted with the above density profile for one chain, determines the density profile of the brush as a whole:

$\phi(z)=\int_z^\infty \frac{\partial n(z,\rho)}{\partial z}\,\epsilon(\rho)\,{\rm d}\rho$

A dry brush has a uniform monomer density up to some altitude $H$. One can show ^[7] that the corresponding end monomer density profile is given by:

$\epsilon_{\rm dry}(\rho,H)=\frac{\rho/H}{Na\sqrt{1-\rho^2/H^2}}$

where $a$ is the monomer size.

The above monomer density profile $n(z,\rho)$ for one single chain minimizes the total elastic energy of the brush,

$U=\int_0^\infty\epsilon(\rho)\,{\rm d}\rho\,\int_0^N\,{\rm d}n\,\frac{kT}{2Na^2}\left(\frac{\partial z(n,\rho)}{\partial n}\right)^2$

regardless of the end monomer density profile $\epsilon(\rho)$, as shown in.^[8][9]

From a dry brush to any brush

As a consequence,^[9] the structure of any brush can be derived from the brush density profile $\phi(z)$. Indeed, the free end distribution is simply a convolution of the density profile with the free end distribution of a dry brush:

$\epsilon(\rho)=\int_\rho^\infty -\frac{{\rm d}\phi(H)}{{\rm d}H}\epsilon_{\rm dry}(\rho,H)$.

Correspondingly, the brush elastic free energy is given by:

$\frac{F_{\rm el}}{kT}=\frac{\pi^2}{24N^2a^5}\int_0^\infty\left\{-z^3\frac{{\rm d}\phi(z)}{{\rm d}z}\right\}{\rm d}z$.

This method has been used to derive wetting properties of polymer melts on polymer brushes of the same species ^[9] and to understand fine interpenetration asymmetries between copolymer lamellae^[10] that may yield very unusual non-centrosymmetric lamellar structures.^[11]

See also

• dendronized polymer

References

1. Milner, S. T. (1991). "Polymer Brushes". Science 251 (4996): 905–14. Bibcode:1991Sci...251..905M. doi:10.1126/science.251.4996.905. PMID 17847384.
2. Halperin, A.; Tirrell, M.; Lodge, T. P. (1992). "Tethered chains in polymer microstructures". 100/1: 31. doi:10.1007/BFb0051635.
3. Laradji, Mohamed; Guo, Hong; Zuckermann, Martin (1994). "Off-lattice Monte Carlo simulation of polymer brushes in good solvents". Physical Review E 49: 3199. Bibcode:1994PhRvE..49.3199L. doi:10.1103/PhysRevE.49.3199.
4. Kaznessis, Yiannis N.; Hill, Davide A.; Maginn, Edward J. (1998). "Molecular Dynamics Simulations of Polar Polymer Brushes". Macromolecules 31: 3116. Bibcode:1998MaMol..31.3116K. doi:10.1021/ma9714934.
5. Szleifer, I; Carignano, MA (1996). "Tethered Polymer Layers". Adv. Chem. Phys. XCIV: 165. doi:10.1002/9780470141533.ch3. ISBN 978-0-471-19143-8.
6. Milner, S. T; Witten, T. A; Cates, M. E (1988). "A Parabolic Density Profile for Grafted Polymers". Europhysics Letters (EPL) 5: 413. Bibcode:1988EL......5..413M. doi:10.1209/0295-5075/5/5/006.
7. Milner, S. T; Witten, T. A; Cates, M. E (1989). Macromolecules 22: 853–861. Bibcode:1989MaMol..22..853M. doi:10.1021/ma00192a057. Missing or empty |title= (help)
8. Zhulina; Borisov (1991). J. Colloid Interface Sci. 44: 507–520. Missing or empty |title= (help)
9. Gay, C. (1997). "Wetting of a polymer brush by a chemically identical polymer melt". Macromolecules 30: 5939–5943. Bibcode:1997MaMol..30.5939G. doi:10.1021/ma970107f.
10. Leibler, L; Gay, C; Erukhimovich, I (1999). "Conditions for the existence of non-centrosymmetric copolymer lamellar systems". Europhysics Letters (EPL) 46: 549–554. Bibcode:1999EL.....46..549L. doi:10.1209/epl/i1999-00277-9.
11. Goldacker, T; Abetz, V; Stadler, R; Erukhimovich, I; Leibler, L (1999). "Non-centrosymmetric superlattices in block copolymer blends". Nature 398 (6723): 137. Bibcode:1999Natur.398..137G. doi:10.1038/18191.

Further reading