Quantum wire

In condensed matter physics, a quantum wire is an electrically conducting wire in which quantum effects influence the transport properties. Usually such effects appear in the dimension of nanowires, so they are also referred to as nanowires.

Quantum effects

If the diameter of a wire is sufficiently small, electrons will experience quantum confinement in the transverse direction. As a result, their transverse energy will be limited to a series of discrete values. One consequence of this quantization is that the classical formula for calculating the electrical resistance of a wire,

R=\rho{l \over A},

is not valid for quantum wires (where \rho is the material's resistivity, l is the length, and A is the cross-sectional area of the wire).

Instead, an exact calculation of the transverse energies of the confined electrons has to be performed to calculate a wire's resistance. Following from the quantization of electron energy, the electrical conductance (the inverse of the resistance) is found to be quantized in multiples of 2e^2/h, where e is the electron charge and h is the Planck constant. The factor of two arises from spin degeneracy. A single ballistic quantum channel (i.e. with no internal scattering) has a conductance equal to this quantum of conductance. The conductance is lower than this value in the presence of internal scattering.[1]

The importance of the quantization is inversely proportional to the diameter of the nanowire for a given material. From material to material, it is dependent on the electronic properties, especially on the effective mass of the electrons. Physically, this means that it will depend on how conduction electrons interact with the atoms within a given material. In practice, semiconductors can show clear conductance quantization for large wire transverse dimensions (~100 nm) because the electronic modes due to confinement are spatially extended. As a result, their Fermi wavelengths are large and thus they have low energy separations. This means that they can only be resolved at cryogenic temperatures (within a few degrees of absolute zero) where the thermal energy is lower than the inter-mode energy separation.

For metals, quantization corresponding to the lowest energy states is only observed for atomic wires. Their corresponding wavelength being thus extremely small they have a very large energy separation which makes resistance quantization observable even at room temperature.

Band structures computed using tight binding approximation for (6,0) CNT (zigzag, metallic), (10,2) CNT (semiconducting) and (10,10) CNT (armchair, metallic).

Carbon nanotubes as quantum wires


The carbon nanotube is an example of a quantum wire. A metallic single-walled carbon nanotube that is sufficiently short to exhibit no internal scattering (ballistic transport) has a conductance that approaches two times the conductance quantum, 4e^2/h. The factor of two arises because carbon nanotubes have two spatial channels.[2]

The structure of a nanotube strongly affects its electrical properties. For a given (n,m) nanotube, if n = m, the nanotube is metallic; if nm is a multiple of 3, then the nanotube is semiconducting with a very small band gap, otherwise the nanotube is a moderate semiconductor. Thus all armchair (n = m) nanotubes are metallic, and nanotubes (6,4), (9,1), etc. are semiconducting.[3]

Applications

Electronic devices

Atomistic simulation result for formation of inversion channel (electron density) and attainment of threshold voltage (IV) in a nanowire MOSFET. Note that the threshold voltage for this device lies around 0.45V.

Nanowires can be used for transistors. Transistors are used widely as fundamental building element in today's electronic circuits. One of the key challenges of building future transistors is ensuring good gate control over the channel. Due to the high aspect ratio, if the gate dielectric is wrapped around the nanowire channel, we can get good electrostatic control of channel potential, thereby turning the transistor on and off efficiently.[4]

sensing using semiconductor nanowires

In an analogous way to FET devices in which the modulation of conductance (flow of electrons/holes) in the device, is controlled by electrostatic potential variation (gate-electrode) of the charge density in the conduction channel, the methodology of a Bio/Chem-FET is based on the detection of the local change in charge density, or so-called “field effect”, that characterizes the recognition event between a target molecule and the surface receptor.

This change in the surface potential influences the Chem-FET device exactly as a ‘gate’ voltage does, leading to a detectable and measurable change in the device conduction.[5]

See also

References

  1. S. Datta, Electronic Transport in Mesoscopic Systems, Cambridge University Press, 1995, ISBN 0-521-59943-1
  2. M. S. Dresselhaus, G. Dresselhaus, and Phaedon Avouris, Carbon nanotubes: synthesis, structure, properties, and applications, Springer, 2001, ISBN 3-540-41086-4
  3. Lu, X.; Chen, Z. (2005). "Curved Pi-Conjugation, Aromaticity, and the Related Chemistry of Small Fullerenes (C60) and Single-Walled Carbon Nanotubes". Chemical Reviews 105 (10): 3643–3696. doi:10.1021/cr030093d. PMID 16218563.
  4. Appenzeller, Joerg; Knoch, Joachim; Bjork, Mikael T.; Riel, Heike; Schmid, Heinz; Riess, Walter (2008). "Toward nanowire electronics". IEEE Transactions on Electron Devices 55 (11): 2827. Bibcode:2008ITED...55.2827A. doi:10.1109/TED.2008.2008011.
  5. Engel, Yoni; Elnathan, R.; Pevzner, A.;, Davidi G.; Flaxer E.; Patolsky F.; (2010). "Supersensitive Detection of Explosives by Silicon Nanowire Arrays". Angewandte Chemie international edition 49 (38): 6830–6835. doi:10.1002/anie.201000847. Cite uses deprecated parameter |coauthors= (help)
This article is issued from Wikipedia - version of the Monday, March 14, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.