Motorcycle fairing
A motorcycle fairing is a shell placed over the frame of some motorcycles, especially racing motorcycles and sport bikes, with the primary purpose to reduce air drag. The secondary functions are the protection of the rider from airborne hazards and wind-induced hypothermia and of the engine components in the case of an accident. A motorcycle windshield may be an integral part of the fairing.[1]
The major benefit of a fairing on sport touring and touring motorcycles is a reduction in fuel consumption.[2] The reduction in aerodynamic drag allows for higher speeds at lower engine rpm, which in turn increases engine life.
There may be a front fairing, or a rear fairing, or both. Alternatively, a single fairing may partially or fully enclose the entire motorcycle, and may also enclose the rider.
History
The importance of streamlining was known very early in the 20th century. Some streamlining was seen on racing motorcycles as early as the 1920s. The effects of aerodynamic drag on motorcycles are very significant.
The term fairing came into use in aircraft aerodynamics with regard to smoothing airflow over a juncture of components where airflow was disrupted. Early streamlining was often unsuccessful resulting in instability. Handlebar fairings, such as those on Harley-Davidson Tourers, sometimes upset the balance of a motorcycle, inducing wobble.[3] The introduction on the BMW R100RS in 1976 marked the beginning of widespread adoption of fairings on sports and touring types of motorcycles.[4]
Originally the fairings were cowlings put around the front of the bike, increasing its frontal area. Gradually they had become an integral part of the design. Modern fairings increase the frontal area at most by 5% compared to a naked machine. Fairing may carry headlights, instruments, and other items. If the fairing is mounted on the frame, mounting equipment on the fairing reduces the weight and rotational inertia of the steering assembly, improving the handling.[5]
Types
Front fairings
Dustbin fairing
A single piece, streamlined shell covering the front half of a motorcycle resembling the nose of an aircraft, sometimes referred to as torpedo fairing. It dramatically reduced the frontal drag, but it was banned by Fédération Internationale de Motocyclisme (FIM) from racing in 1958, because it was thought that the frontal point of wind pressure made them highly unstable even with small amounts of yaw.[5] Other reasons cited for the ban were to ensure adequate steering range (lock-to-lock) and stability in crosswinds. FIM regulations forbid streamlining beyond the wheel spindles and require the rider's arms and legs to be visible from the side.[5]
Dolphin fairing
This was called so because, in early models, the front wheel mudguard streamlined with the rising windshield part of the fairing resembled the dolphin's snout from the side view. Further developments on this design became the norm after the ban of the dustbins.[5][6]
Full fairing
A full fairing is a large front-mounted fairing, and should not be confused with cabin motorcycle or streamliner motorcycle fairings which fully or partially enclose the entire motorcycle.
Full fairings cover both upper and lower portions of the motorcycle, as distinct from a half fairing, which only has an upper section, and leaves the lower half of the motorcycle exposed. The fairing on a race or sport bike is meant as an aerodynamic aid, so the windscreen is rarely looked through. If the rider is sitting up at speed he will be buffeted by his rapid progress through the air and act as a parachute, slowing the bike, while if the rider lies flat on the tank behind the windscreen he generates much less aerodynamic drag. The high windscreen and handlebar width of a touring fairing protect the upright rider from the worst of this, and the windscreen is functional. Full fairings can also provide protection to the engine and chassis in the event of a crash where the fairings, rather than the engine covers and/or frame, slide on the road.
Half fairing
Half fairings usually feature a windscreen and extend below the handlebars, possibly as far down as the sides of the cylinder block, but generally do not cover the sides of the crankcase or gearbox. Aftermarket kits are available to extend some half fairings into full fairings. Due to the popularity of these kits, some motorcycle manufacturers have started to supply their own full fairing conversion kits and even offer their half faired models new with a full fairing kit fitted at the factory.
Quarter fairing
A windscreen and minimal fairing extending around the headlamp fixed to the triple clamp. Also called a café fairing or bikini fairing, it stops well below the level of the rider's head, relying primarily on air deflection to protect the rider's head and chest from the slipstream.
Belly pan
Quarter and half fairings are often paired with a belly pan below the engine for diverting air flow away from under the engine to reduce aerodynamic lift, as well as cosmetic reasons. Some track day or racing rules require belly pans to catch leaked fluids.[7]
Rear fairings
A tail fairing, sometimes referred to as a tail unit or race tail, is mounted behind the seat and rider. Some also extend to the sides of, and below, the saddle.
Kawasaki became the first manufacturer to incorporate a tail fairing on a mass production motorcycle when identical tail units (albeit with different colour schemes) were fitted to the 1972 250cc S1 Mach I, 350cc S2 Mach II, and 750cc H2 Mach IV models.
Streamliner
A streamliner motorcycle, such as the NSU Delphin III, uses a fairing which completely encloses both the entire motorcycle and the rider to provide the best possible drag coefficient ratio.[8]
Materials
Acrylonitrile butadiene styrene (ABS) plastic is commonly used in original equipment sport bikes and certain aftermarket fairing manufacturers due to its strong, flexible and light weight properties. The advantage of ABS over other plastics is that it combines the strength and rigidity of acrylonitrile and styrene with the toughness of polybutadiene rubber. The proportions of each property vary based on the targeted result.
There are two common methods of producing an ABS plastic fairing: injection and compression molding.
- Injection molding: ABS plastic is melted and injected into mold cavity. Constant pressure is applied to allow for material shrinkage. The plastic then cools and hardens in the mold. Injection molds allows for uniform thickness throughout the entire piece. It gives the most accurate end product that fits well. It is how most manufacturers make their plastics.
- Compression molding: The plastic is generally preheated is placed into a heated metal mold cavity and pressure is applied to force the plastic to contract and take the shape of the mold. Heat and pressure is kept until the plastic cures the mold. The excess plastic is cut away and removed from the mold. Disadvantages to compression mold include varying product consistency and flashing, which is excess material attached to the molded part that needs to be removed where two or more parts of the mold meet.
Fiberglass is made of woven fibers, and is used as a reinforcing agent for many polymer products. The composite properly known as glass-reinforced plastic (GRP), is normally referred to by the name of its reinforcing material. Fiberglass fairings are commonly used on the race track. In most cases fiberglass is lighter, and more durable than ABS Plastic. Damaged fiberglass can be repaired by applying new layers of woven fiberglass cloth mixed with a polymer such as epoxy over the damaged area, followed by sanding and finishing.
Carbon-fiber-reinforced polymer is the lightest, but most expensive, fairing material. It is used on the most extreme sport and racing motorcycle fairings.[9]
See also
Notes
- ↑ Tony Foale, Motorcycle Handling and Chassis Design, ISBN 84-933286-3-4 , Chapter 5: "Aerodynamics"
- ↑ Fuel Economy Begins with Streamlining
- ↑ Obradovich, George (August 29, 2008). "2009 Harley-Davidson Electra Glide Standard Review". Motorcycle.com. VerticalScope. Archived from the original on 2013-09-15. Retrieved 2014-09-21.
- ↑ Tong, David (2012) [2005]. "Sport-Touring Defined: The BMW RS Series". chuckhawks.com. Chuck Hawks. Archived from the original on 2014-02-09.
- 1 2 3 4 John Robinson, "Motorcycle Tuning: Chassis", ISBN 0-7506-1840-X, p.132
- ↑ Motor Cycle 24 September 1964, p.582 On the Four Winds by 'Nitor'. "...about 1953, Moto Guzzi factory models appeared with fairings not unlike those used today. The following year the NSU factory took up the idea and evolved a light alloy fairing rather more enveloping than the Moto Guzzi pattern. It had a very rounded front from which protruded a skimpy, integral mudguard; in side view the fore part had a fancied resemblance to a dolphin's snout. Anyway, NSU thought so, and the German models were officially called 'dolphins'. Later, of course, full streamlining ruled the roost until banned by the FIM. The earlier type fairing came back, this time without the integral mudguard peak and with a flatter frontal aspect. By then the dolphin likeness had disappeared, but the old NSU name still stuck and, eventually, gained universal acceptance.". Accessed and added 2014-06-30
- ↑ Larson, Kent (2005), Motorcycle Track Day Handbook, MotorBooks/MBI Publishing Company, p. 115, ISBN 978-0-7603-1761-7, retrieved 2011-03-05
- ↑ NSU Breaks 200 MPH Barrier
- ↑ Cameron, Kevin (1998), Sportbike Performance Handbook, St. Paul MN: Motorbooks, p. 8, ISBN 978-0-7603-0229-3
References
- P. E. Freathy, J. D. Potter (1979) "An Investigation of the Performance of the Motorcycle Fairing", University of Bristol, Dept. of Aeronautical Engineering
| |||||||||||||||||||||||||||||||||||||||||||||||||||||
