Radio receiver

Early broadcast radio receiver. Truetone model from about 1940

In radio communications, a radio receiver (commonly also called a radio) is an electronic device that receives radio waves and converts the information carried by them to a usable form. It is used with an antenna. The antenna intercepts radio waves (electromagnetic waves) and converts them to tiny alternating currents which are applied to the receiver, and the receiver extracts the desired information. The receiver uses electronic filters to separate the desired radio frequency signal from all the other signals picked up by the antenna, an electronic amplifier to increase the power of the signal for further processing, and finally recovers the desired information through demodulation.

The information produced by the receiver may be in the form of sound (an audio signal), images (a video signal) or data (a digital signal).[1] A radio receiver may be a separate piece of electronic equipment, or an electronic circuit within another device. Devices that contain radio receivers include television sets, radar equipment, two-way radios, cell phones, wireless computer networks, GPS navigation devices, satellite dishes, radio telescopes, bluetooth enabled devices, garage door openers, and baby monitors.

In consumer electronics, the terms radio and radio receiver are often used specifically for receivers designed to reproduce the audio (sound) signals transmitted by radio broadcasting stations, historically the first mass-market commercial radio application.

Types of radio receivers

ALMA's Band 5 receivers detect electromagnetic radiation with wavelengths between about 1.4 and 1.8 mm (211 and 163 GHz).[2] The picture shows only peripheric components of the receiver such as the Local Oscillator multiplier chain. The main receiver components of the ALMA band 5 receiver, such as horn antennae, superconductive SIS mixers, and cryogenic low-noise amplifiers, reside on a cartridge that is inserted into a cryostat and cooled to 4K, 12K, and 90K, respectively

Various types of radio receivers may include:

Consumer audio receivers

In the context of home audio systems, the term "receiver" often refers to a combination of a tuner, a preamplifier, and a power amplifier all on the same chassis. Audiophiles will refer to such a device as an integrated receiver, while a single chassis that implements only one of the three component functions is called a discrete component. Some audio purists still prefer three discrete units - tuner, preamplifier and power amplifier - but the integrated receiver has, for some years, been the mainstream choice for music listening. The first integrated stereo receiver was made by the Harman Kardon company, and came onto the market in 1958. It had undistinguished performance, but it represented a breakthrough to the "all in one" concept of a receiver, and rapidly improving designs gradually made the receiver the mainstay of the marketplace. Many radio receivers also include a loudspeaker.

Hi-Fi / Home theater

Main article: Home cinema

Today AV receivers are a common component in a high-fidelity or home-theatre system. The receiver is generally the nerve centre of a sophisticated home-theatre system providing selectable inputs for a number of different audio components like record players, CD players, tape decks and video components like VCRs, DVD players, video game consoles and television sets.

With the decline of gramophone record vinyl discs, modern receivers tend to omit inputs for phonograph turntables, which have separate requirements of their own. All other common audio/visual components can use any of the identical line-level inputs on the receiver for playback, regardless of how they are marked (the "name" on each input is mostly for the convenience of the user). For instance, a second CD player can be plugged into an "AUX" input, and will work the same as it will in the "CD" input jacks.

Some receivers can also provide digital signal processors (DSP) to give a more realistic auditory illusion of listening in a concert hall. Digital audio S/PDIF and USB connections are also common today. The home theater receiver, in the vocabulary of consumer electronics, comprises both the 'radio receiver' and other functions, such as control, sound processing, and power amplification. The standalone radio receiver is usually known in consumer electronics as a tuner.

Some modern integrated receivers can send audio out to seven loudspeakers and an additional channel for a subwoofer and often include connections for headphones. Receivers vary greatly in price, and support stereophonic or surround sound. A high-quality receiver for dedicated audio-only listening (two channel stereo) can be relatively inexpensive. Excellent ones can be purchased for $300 or less. Because modern receivers are purely electronic devices with no moving parts unlike electromechanical devices like turntables and cassette decks, they tend to offer many years of trouble-free service. In recent years, the home theater in a box has become common, which often integrates a surround-capable receiver with a DVD player. The user simply connects it to a television, perhaps other components, and a set of loudspeakers.

Portable radios

Early portable radio receiver

Portable radios include simple transistor radios that are typically monoaural and receive the AM, FM, or short wave broadcast bands. FM, and often AM, radios are sometimes included as a feature of portable DVD/CD, MP3 CD, and USB key players, as well as cassette player/recorders.

AM/FM stereo car radios can be a separate dashboard mounted component or a feature of in car entertainment systems.

A boombox or boom-box, sometimes known as a ghetto blaster or a jambox, in parts of Europe as a "radio-cassette", is a name given to larger portable stereo systems capable of playing radio stations and recorded music, often at a high level of volume.

Self-powered portable radios, such as clockwork radios are used in developing nations or as part of an emergency preparedness kit.[3]

History

Radio waves were first generated by German physicist Heinrich Hertz in 1887, who used micrometer spark gaps attached to dipole and loop antennas to detect them.[4][5] However these primitive devices are more accurately described as radio wave sensors, not "receivers", as they could only detect radio waves within about 100 feet of the transmitter, and were not used for communication.

Spark era

Main article: Wireless telegraphy
Guglielmo Marconi who built the first radio receivers, with his early spark transmitter (right) and coherer receiver (left) from the 1890s. The receiver records the Morse code on paper tape
Generic block diagram of an unamplified radio receiver from the wireless telegraphy era[6]

The earliest radio communication systems, used during the first three decades of radio, 1887-1917, called the wireless telegraphy or "spark" era, used spark gap transmitters which generated radio waves by discharging a capacitance through an electric spark.[7][8][9] Each spark produced a transient pulse of radio waves consisting of a sinusoidal wave which decreased rapidly exponentially to zero.[4][5] Spark transmitters produced strings of these damped waves, and could not generate the sinusoidal continuous waves which are modulated to carry sound in modern AM and FM transmission. Thus spark transmitters could not transmit audio (sound), and instead transmitted information by radiotelegraphy; the transmitter was switched on and off rapidly by the operator using a telegraph key, creating different length pulses of these damped radio waves ("dots" and "dashes") to spell out text messages in Morse code.[5][8]

Therefore, the first radio receivers did not have to demodulate the radio signal - extract an audio signal from it as modern receivers do - just detect the presence or absence of the radio signal, and produce a sound in the earphone during the "dots" and "dashes" of the Morse code.[5] The device which did this was called a "detector". Since there were no amplifying devices during this era, the sensitivity of the receiver mostly depended on the detector, and many different detector devices were tried. Radio receivers during the spark era (see diagram) consisted of these parts:

The signal from the spark gap transmitter consisted of damped waves repeated at an audio frequency rate, from 120 to perhaps 4000 per second, so in the earphone the signal sounded like a musical tone or buzz, and the Morse code "dots" and "dashes" sounded like beeps.

The first person to use radio waves for communication was Guglielmo Marconi.[8][11] Marconi invented little himself, but he was first to believe that radio could be a practical communication medium, and singlehandedly developed the first wireless telegraphy systems, transmitters and receivers, beginning in 1895,[11] mainly by improving technology invented by others.[8][12][13][14] [15][16] Oliver Lodge and Alexander Popov were also experimenting with similar radio wave receiving apparatus at the same time in 1895,[13][17] but they are not known to have transmitted Morse code during this period,[8][11] just strings of random pulses. Therefore, Marconi is usually given credit for building the first radio receivers.

Coherer receiver

Main article: Coherer
Coherer from 1904 as developed by Marconi.
One of Marconi's first coherer receivers, used in his "black box" demonstration at Toynbee Hall, London, 1896. The coherer is at right, with the "tapper" just behind it, The relay is at left, batteries are in background
A typical commercial radiotelegraphy receiver from the first decade of the 20th century. The coherer (right) detects the pulses of radio waves, and the "dots" and "dashes" of Morse code were recorded in ink on paper tape by a siphon recorder (left) and transcribed later.

The first radio receivers invented by Marconi, Oliver Lodge and Alexander Popov in 1895 used a primitive radio wave detector called a coherer, invented in 1890 by Edouard Branly and improved by Oliver Lodge and Marconi.[4][8][10][13][17][18] The coherer was a glass tube with metal electrodes at each end, with loose metal powder between the electrodes.[4][8][19] It initially had a high resistance. When a radio signal was applied to the electrodes, its resistance dropped and it conducted electricity. In the receiver the coherer was connected directly between the antenna and ground. In addition to the antenna, the coherer was connected in a DC circuit with a battery and relay. When the radio wave reduced the resistance of the coherer, the current from the battery flowed through it, turning on the relay to ring a bell or make a mark on a paper tape in a siphon recorder. In order to restore the coherer to its previous nonconducting state to receive the next pulse of radio waves, it had to be tapped mechanically to disturb the metal particles.[4][8][17] This was done by a "decoherer", a clapper which struck the tube, operated by an electromagnet powered by the relay.

The coherer is an obscure antique device, and even today there is some disagreement about the exact physical mechanism by which it worked.[4][12] However it can be seen that it was essentially a bistable device, a radio-wave-operated switch, and so it could not demodulate the later amplitude modulated (AM) radio signals that carried sound.[4][12]

Marconi found that by using an elevated wire monopole antenna instead of Hertz's dipole antennas he could transmit longer distances, beyond the curve of the Earth, culminating in his historic transatlantic wireless transmission on December 12, 1901 from Poldhu, Cornwall to St. John's, Newfoundland, a distance of 3500 km (2200 miles), which was received by a coherer.[12][16] However the usual range of coherer receivers even with the powerful transmitters of this era was limited to a few hundred miles.

The coherer remained the dominant detector used in early radio receivers for about 10 years,[19] until replaced by the crystal detector and electrolytic detector around 1907. In spite of much development work, it was a very crude unsatisfactory device.[4][8] It was not very sensitive, and also responded to impulsive radio noise (RFI), such as nearby lights being switched on or off, as well as to the intended signal.[8][19] Due to the cumbersome mechanical "tapping back" mechanism it was limited to a data rate of about 12-15 words per minute of Morse code, while a spark-gap transmitter could transmit Morse at up to 100 WPM with a paper tape machine.[20][21]

Other early detectors

The coherer's poor performance motivated a great deal of research to find better radio wave detectors, and many were invented. Some strange devices were tried; researchers experimented with using frog legs and even a human brain from a cadaver as detectors.[4]

By the first years of the 20th century, experiments in using amplitude modulation (AM) to transmit sound by radio (radiotelephony) were being made. So a second goal of detector research was to find detectors that could demodulate an AM signal, extracting the audio (sound) signal from the radio carrier wave. It was found by trial and error that this could be done by a detector that exhibited "asymmetrical conduction"; a device that conducted current in one direction but not in the other. This rectified the alternating current radio signal, removing one side of the carrier cycles, leaving a pulsing DC current whose amplitude varied with the audio modulation signal. When applied to an earphone this would reproduce the transmitted sound.

Below are the detectors that saw wide use before vacuum tubes took over around 1920.[22][23] All except the magnetic detector could rectify and therefore receive AM signals:

Magnetic detector
Electrolytic detector
Early Fleming valve.
Marconi valve receiver for use on ships had two Fleming valves (top) in case one burned out. It was used on the RMS Titanic.
A galena cat's whisker detector from a 1920s crystal radio

During the vacuum tube era, the term "detector" changed from meaning a radio wave detector to mean a demodulator, a device that could extract the audio modulation signal from a radio signal. That is its meaning today.

Tuning

The word "tuning" means adjusting the frequency of the receiver (its passband) to the frequency of the desired radio transmitter, to receive the desired radio transmission. Although in many modern radio receivers (such as television sets) this is done automatically by pressing a "channel up" or "channel down" button, some older radios still use the traditional method of turning a "tuning" knob until the station is heard in the speaker. However the very first receivers in the spark era could not be tuned at all.

The first receivers had no tuned circuit, the detector was connected directly between the antenna and ground. Due to the lack of any frequency selective components besides the antenna, the bandwidth of the receiver was equal to the broad bandwidth of the antenna.[9][10][18][34] This was acceptable and even necessary because the first Hertzian spark transmitters also lacked a tuned circuit. Due to the impulsive nature of the spark, they radiated a very "noisy" signal, the energy of the radio waves was spread over a very wide band of frequencies, a wide bandwidth.[35][36] To receive enough energy from this wideband signal the receiver had to have a wide bandwidth also.

It was found that when more than one spark transmitter was radiating in a given area, their frequencies overlapped, so their signals interfered with each other, resulting in garbled reception.[9][34][37] It became clear that, if multiple transmitters were to operate simultaneously, some method of selective signaling was needed, to allow the receiver to select which transmitter's signal to receive.[37][38] In 1892, William Crookes had given an influential lecture[39] on radio in which he suggested using resonance (then called "syntony") to reduce the bandwidth of transmitters so they didn't interfere. Different transmitters could then be "tuned" to transmit on different frequencies.[16][35][40] The receiver would also have a resonant circuit (tuned circuit), and could receive a particular transmission by "tuning" its resonant circuit to the same frequency as the transmitter, analogously to tuning a musical instrument. This is the system used in all modern radio.

The first person to use tuning in radio was Nikola Tesla, who in a March 1893 lecture had demonstrated a wireless system that, although it was intended for wireless transmission of power, had all the elements of a "tuned" radio communication system.[13][16][40][41] A spark-excited grounded resonant transformer with a wire antenna transmitted radio waves, which were received across the room with a wire antenna connected to another resonant transformer tuned to the frequency of the transmitter, which lighted a Geissler tube.[13][40] This was the first use of the "four tuned circuit" wireless concept (next section) which was later patented by Marconi.[13][40] However Tesla was mainly interested in wireless power, and never developed a practical radio comunication system.[42][43][44]

By 1897 the advantages of tuned systems had become clear, and Marconi and the other wireless researchers had incorporated tuned circuits, consisting of capacitors and inductors connected together, into their transmitters and receivers.[9][13][16][18][34][41] The tuned circuit acted like an electrical analog of a tuning fork. It had a high impedance at its resonant frequency, but a low impedance at all other frequencies. Connected between the antenna and the detector it served as a bandpass filter, passing the signal of the desired station to the detector, but routing all other signals to ground.[10] The frequency of the station received f was determined by the capacitance C and inductance L in the tuned circuit:

f = {1 \over 2 \pi \sqrt{LC} }\,

Inductive coupling and the "four circuit" patent

Marconi's inductively coupled coherer receiver from his controversial April 1900 "four circuit" patent.
Braun receiving transformer from 1904
Crystal receiver from 1914 with "loose coupler" tuning transformer. The secondary coil (1) can be slid in or out of the primary (in box) to adjust the coupling. Other components: (2) primary tuning capacitor, (3) secondary tuning capacitor, (4) loading coil, (5) crystal detector, (8) headphones

In order to reject radio noise and interference from other transmitters near in frequency to the desired station, the bandpass filter (tuned circuit) in the receiver has to have a narrow bandwidth, allowing only a narrow band of frequencies through.[9][10] The form of bandpass filter that was used in the first receivers, which is still used in some modern receivers, was the double-tuned inductively-coupled circuit, or resonant transformer (oscillation transformer or RF transformer).[9][13][16][18][41][45] The antenna and ground were connected to a coil of wire, which was magnetically coupled to a second coil with a capacitor across it, which fed current to the detector.[10] The RF alternating current from the antenna through the primary coil created a magnetic field which induced a current in the secondary coil. Both primary and secondary were tuned circuits;[34] the primary coil resonated with the capacitance of the antenna, while the secondary coil resonated with the capacitor across it. Both were adjusted to the same resonant frequency.

This circuit had two advantages.[10] One was that by using the correct turns ratio, the impedance of the antenna could be matched to the impedance of the receiver, to transfer maximum RF power to the receiver. Impedance matching was important to achieve maximum receiving range in the unamplified receivers of this era.[6][10] The coils usually had taps which could be selected by a multiposition switch. The second advantage was that due to "loose coupling" it had a much narrower bandwidth than a simple tuned circuit, and the bandwidth could be adjusted.[9][45] Unlike in an ordinary transformer, the two coils were "loosely coupled"; separated physically so not all the magnetic field from the primary passed through the secondary, reducing the mutual inductance. This gave the coupled tuned circuits much "sharper" tuning, a narrower bandwidth than a single tuned circuit. In the "Navy type" loose coupler (see picture), widely used with crystal receivers, the smaller secondary coil was mounted on a rack which could be slid in or out of the primary coil, to vary the mutual inductance between the coils.[9][46] When the operator encountered an interfering signal at a nearby frequency, the secondary could be slid further out of the primary, reducing the coupling, which narrowed the bandwidth, rejecting the interfering signal. A disadvantage was that all three adjustments in the loose coupler - primary tuning, secondary tuning, and coupling - were interactive; changing one changed the others. So tuning in a new station was a process of successive adjustments.

As mentioned above, Nikola Tesla first used the resonant transformer for both transmitting and receiving radio waves in 1893,[40][47] and had patented it in 1897.[13][48] Around 1897 other wireless researchers Ferdinand Braun,[9][16] Oliver Lodge[49] and John Stone Stone[50] also incorporated it into radio systems which they patented.[13][34][36][41][47] Braun discovered the advantages of loose coupling in 1902.[16][51] In spite of this prior art, in 1900 Marconi claimed rights to both the resonant transformer transmitter and receiver circuits in his controversial "four circuit" patent,[9][13][16][34][41][52] which gave his company a decisive advantage in radio technology.[36][40] Lodge, Stone and Tesla sued Marconi for patent infringement, beginning a long-running litigation. With its deep pockets the Marconi Company defended the patent for 43 years, but in 1943, long after it had expired, the US Supreme Court invalidated it, citing the Lodge, Stone, and Tesla patents.[13][40]

Selectivity became more important as spark transmitters were replaced by continuous wave transmitters which transmitted on a narrow band of frequencies, and broadcasting led to a proliferation of closely spaced radio stations crowding the radio spectrum.[10] Resonant transformers continued to be used as the bandpass filter in vacuum tube radios, and new forms such as the variometer were invented.[46][53] Another advantage of the double-tuned transformer for AM reception was that when properly adjusted it had a "flat top" frequency response curve as opposed to the "peaked" response of a single tuned circuit.[54] This allowed it to pass the sidebands of AM modulation on either side of the carrier with little distortion, unlike a single tuned circuit which attenuated the higher audio frequencies. Until recently the bandpass filters in the superheterodyne circuit used in all modern receivers were made with resonant transformers, called IF transformers.

Crystal radio receiver

Main article: Crystal radio
Prior to 1920 the crystal receiver was the main type used in wireless telegraphy stations, and sophisticated models were made, like this Marconi Type 106 from 1915.
Family listening to the first broadcasts around 1920 with a crystal receiver. The mother and father have to share an earphone
After vacuum tube receivers appeared around 1920, the crystal set became a simple cheap alternative radio used by youth and the poor.
Simple crystal radio. The capacitance of the wire antenna connected to the coil serves as the capacitor in the tuned circuit.
Typical "loose coupler" crystal radio circuit

Although it was invented in 1904 in the wireless telegraphy era, the crystal radio receiver could also rectify AM transmissions and served as a bridge to the broadcast era. In addition to being the main type used in commercial stations during the wireless telegraphy era, it was the first receiver to be used widely by the public.[55] During the first two decades of the 20th century, radio listening became a popular hobby, which accelerated as stations began to transmit in AM voice (radiotelephony) instead of telegraphy, and the crystal was the simplest cheapest detector. The millions of people who purchased or homemade these inexpensive reliable receivers created the mass listening audience for the first radio broadcasts, which began around 1920.[56] Superseded by vacuum tube receivers in the 1920s, it continued to be used by youth and the poor until World War 2.[55] Today crystal radios, the simplest type of radio receivers, are constructed by students as educational science projects.

The crystal radio used a crystal detector called a cat's whisker detector, invented by Harrison H. C. Dunwoody and Greenleaf Whittier Pickard in 1904, to rectify the radio signal to extract the audio from the radio frequency carrier.[10][25][57] It consisted of a mineral crystal, usually galena (PbS, lead sulfide) which was lightly touched by a fine springy wire (the "cat whisker") on an adjustable arm.[25][58] The resulting crude semiconductor junction functioned as a Schottky barrier diode, it only conducted current in one direction. Only particular sites on the crystal surface functioned as rectifying junctions, and the junction could be disrupted by the slightest vibration. So a usable site was found by trial and error before each use; the operator would drag the cat's whisker across the crystal until the radio began functioning.

Like other receivers of this era the crystal radio was unamplified and ran off the power of the radio waves received from the radio station, so it had to be listened to with earphones; it could not drive a loudspeaker.[10][58] It required a long wire antenna, and its sensitivity depended on how large the antenna was. During the wireless era it was used in commercial and military longwave stations with huge antennas to receive long distance radiotelegraphy traffic, even including transatlantic traffic.[59][60] However, when used to receive broadcast stations a typical home crystal set had a more limited range of 25 – 100 miles.[61] In sophisticated crystal radios the "loose coupler" inductively-coupled tuned circuit was used to increase the Q. However it still had poor selectivity compared to modern receivers.[58]

Heterodyne receiver and BFO

Main article: Heterodyne
Radio receiver with Poulsen "tikker" consisting of a commutator disk turned by a motor to interrupt the carrier.

Beginning around 1905 continuous wave (CW) transmitters began to replace spark transmitters for radiotelegraphy because they had much greater range. The first continuous wave transmitters were the Poulsen arc invented in 1904 and the Alexanderson alternator developed 1906-1910, which were replaced by vacuum tube transmitters beginning around 1920.[5]

The continuous wave radiotelegraphy signals produced by these transmitters required a different method of reception.[62] The radiotelegraphy signals produced by spark gap transmitters consisted of strings of damped waves repeating at an audio rate, so the "dots" and "dashes" of Morse code were audible as a tone or buzz in the receivers' earphones. However the new continuous wave radiotelegraph signals simply consisted of pulses of unmodulated carrier (sine waves). These were inaudible in the receiver headphones. To receive this new modulation type, the receiver had to produce some kind of tone during the pulses of carrier.

The first crude device that did this was the "ticker" or "tikker", invented in 1908 by Valdemar Poulsen.[22][62] [63] This was a vibrating interrupter with a capacitor at the tuner output which served as a rudimentary modulator, interrupting the carrier at an audio rate, thus producing a buzz in the earphone when the carrier was present.[64] A similar device was the "tone wheel" invented by Rudolph Goldschmidt, a wheel spun by a motor with contacts spaced around its circumference, which made contact with a stationary brush.

Fessenden's heterodyne radio receiver circuit

In 1901 Reginald Fessenden had invented a better means of accomplishing this.[62][63][65][66] In his heterodyne receiver an unmodulated sine wave radio signal at a frequency fO offset from the incoming radio wave carrier fC was applied to a rectifying detector such as a crystal detector or electrolytic detector, along with the radio signal from the antenna. In the detector the two signals mixed, creating two new heterodyne (beat) frequencies at the sum fC + fO and the difference fC  fO between these frequencies. By choosing fO correctly the lower heterodyne fC  fO was in the audio frequency range, so it was audible as a tone in the earphone whenever the carrier was present. Thus the "dots" and "dashes" of Morse code were audible as musical "beeps". A major attraction of this method during this pre-amplification period was that the heterodyne receiver actually amplified the signal somewhat, the detector had "mixer gain".[63]

The receiver was ahead of its time, because when it was invented there was no oscillator capable of producing the radio frequency sine wave fO with the required stability.[67] Fessenden first used his large radio frequency alternator,[64] but this wasn't practical for ordinary receivers. The heterodyne receiver remained a laboratory curiosity until a cheap compact source of continuous waves appeared, the vacuum tube electronic oscillator[63] invented by Edwin Armstrong and Alexander Meissner in 1913.[22][68] After this it became the standard method of receiving CW radiotelegraphy. The heterodyne oscillator is the ancestor of the beat frequency oscillator (BFO) which is used to receive radiotelegraphy in communications receivers today. The heterodyne oscillator had to be retuned each time the receiver was tuned to a new station, but in modern superheterodyne receivers the BFO signal beats with the fixed intermediate frequency, so the beat frequency oscillator can be a fixed frequency.

Armstrong later used Fessenden's heterodyne principle in his superheterodyne receiver (below).[63][64]

Vacuum tube era

Unlike today, when almost all radios use a variation of the superheterodyne design, during the 1920s vacuum tube radios used a variety of competing circuits.
During the "Golden Age of Radio" (1920 to 1950), families gathered to listen to the home radio in the evening, such as this Zenith console model 12-S-568 from 1938, a 12 tube superheterodyne with pushbutton tuning and 12 inch cone speaker.

The Audion (triode) vacuum tube invented by Lee De Forest in 1906 was the first practical amplifying device and revolutionized radio.[29] Vacuum tube transmitters replaced spark transmitters and made possible four new types of modulation: continuous wave (CW) radiotelegraphy, amplitude modulation (AM) around 1915 which could carry audio (sound), frequency modulation (FM) around 1938 which had much improved audio quality, and single sideband (SSB).

The amplifying vacuum tube used energy from a battery or electrical outlet to increase the power of the radio signal, so it resulted in more sensitive receivers with a greater reception range. The increased audio output power also allowed them to drive loudspeakers instead of earphones, permitting more than one person to listen. The first loudspeakers were produced around 1915. These changes caused radio listening to evolve explosively from a solitary hobby to a popular social and family pastime. The development of amplitude modulation (AM) and vacuum tube transmitters during World War 1, and the availability of cheap receiving tubes after the war, set the stage for the start of AM broadcasting, which sprang up spontaneously around 1920.

The advent of radio broadcasting increased the market for radio receivers greatly, and transformed them into a consumer product.[69][70][71] At the beginning of the 1920s the radio receiver was a forbidding high-tech device, with many cryptic knobs and controls requiring technical skill to operate, housed in an unattractive black metal box, with a tinny-sounding horn loudspeaker.[70] By the 1930s, the broadcast receiver had become a piece of furniture, housed in an attractive wooden case, with standardized controls anyone could use, which occupied a respected place in the home living room. In the early radios the multiple tuned circuits required multiple knobs to be adjusted to tune in a new station. One of the most important ease-of-use innovations was "single knob tuning", achieved by linking the tuning capacitors together mechanically.[70][71] The dynamic cone loudspeaker invented in 1924 greatly improved audio frequency response over the previous horn speakers, allowing music to be reproduced with good fidelity.[70][72] Convenience features like large lighted dials, tone controls, pushbutton tuning, tuning indicators and automatic gain control (AGC) were added.[69][71] The receiver market was divided into the above broadcast receivers and communications receivers, which were used for two-way radio communications such as shortwave radio.[73]

A vacuum tube receiver required several power supplies at different voltages, which in early radios were supplied by separate batteries. These were the standard batteries used in early radios:[74][75][76]

By 1930 adequate rectifier tubes were developed, and the expensive batteries were replaced by a transformer power supply that worked off the house current.[69][70]

Vacuum tubes were bulky, expensive, had a limited lifetime, consumed a large amount of power and produced a lot of waste heat, so the number of tubes a receiver could economically have was a limiting factor. Therefore, a goal of tube receiver design was to get the most performance out of a limited number of tubes. The major radio receiver designs, listed below, were invented during the vacuum tube era.

A defect in many early vacuum tube receivers was that the amplifying stages could oscillate, act as an oscillator, producing unwanted radio frequency alternating currents.[10][77][78] These parasitic oscillations mixed with the carrier of the radio signal in the detector tube, producing audible beat notes (heterodynes); annoying whistles, moans, and howls in the speaker. This was due to feedback in the amplifiers; one major feedback path was the capacitance between the plate and grid in early triodes.[77][78] This was solved by the Neutrodyne circuit, and later the development of the tetrode and pentode around 1930.

Edwin Armstrong is one of the most important figures in radio receiver history, and during this period invented technology which continues to dominate radio communication.[64] He was the first to give a correct explanation of how De Forest's triode tube worked. He invented the feedback oscillator, regenerative receiver, the superregenerative receiver, the superheterodyne receiver, and modern frequency modulation (FM).

The first vacuum tube receivers

De Forest's first commercial Audion receiver, the RJ6 which came out in 1914. The Audion tube was always mounted upside down, with its delicate filament loop hanging down, so it did not sag and touch the other electrodes in the tube.
Example of single tube triode grid-leak receiver from 1920, the first type of amplifying radio receiver.

The first amplifying vacuum tube, the Audion, a crude triode, was invented in 1906 by Lee De Forest as a more sensitive detector for radio receivers, by adding a third electrode to the thermionic diode detector, the Fleming valve.[29][53][79] It was not widely used until its amplifying ability was recognized around 1912.[29] The first tube receivers, invented by De Forest and built by hobbyists until the mid 1920s, used a single Audion which functioned as a grid-leak detector which both rectified and amplified the radio signal.[53][77][80] The grid-leak detector circuit was employed in most vacuum tube radios until the 1930s.

To give enough output power to drive a loudspeaker, 2 or 3 additional Audion stages were needed for audio amplification.[53] Many early hobbyists could only afford a single tube receiver, and listened to the radio with earphones, so early tube amplifiers and speakers were sold as add-ons.

In addition to very low gain of about 5, the primitive Audion had erratic characteristics because it was incompletely evacuated, some residual air was left in the tube by De Forest, who believed that ionization was key to its operation.[81] This made it a more sensitive detector[81] but also caused its electrical characteristics to vary during use.[53] As the tube heated up, gas released from the metal elements would change the pressure in the tube, changing the plate current and other characteristics, so it required periodic bias adjustments to keep it at the correct operating point. Each Audion stage usually had a rheostat to adjust the filament current, and often a potentiometer or multiposition switch to control the plate voltage. The filament rheostat was also used as a volume control.

By 1914, Harold Arnold at Western Electric and Irving Langmuir at GE had realized that the residual gas in the tube that caused these problems was not necessary, and were able to evacuate tubes to a lower pressure of 10−9 atm, producing the first "hard vacuum" triodes.[81] These more stable tubes did not require bias adjustments and allowed radios to have fewer controls and be more user friendly. During World War 1 civilian radio use was prohibited, but by 1920 these tubes came on the market and large scale production of vacuum tube radios began. The "soft" incompletely-evacuated tubes were used as detectors through the 1920s then became obsolete.

Regenerative (autodyne) receiver

Main article: Regenerative receiver
Block diagram of regenerative receiver
Circuit of single tube Armstrong regenerative receiver
Homemade Armstrong regenerative receiver, 1922. The "tickler" coil (L3) is visible on the front panel, coupled to the input tuning coils.
Regenerative receiver from the early 1920s, the Paragon RA-10. The separate 3-tube audio amplifier unit (right) was needed to give sufficient power for the horn loudspeaker. The 4 cylindrical dry cell "A" batteries (right rear) powered the tube filaments, while the 2 rectangular "B" batteries provided plate voltage.
Homemade one-tube Armstrong regenerative receiver from the 1940s. The tickler coil is a variometer winding mounted on a shaft inside the tuning coil (upper right) which can be rotated by a knob on the front panel.

The regenerative receiver, invented by Edwin Armstrong[82] in 1913 when he was a 23-year-old college student,[83] was used very widely until the late 1920s particularly by hobbyists who could only afford a single-tube radio. Today transistor versions of the circuit are still used in a few inexpensive applications like walkie-talkies. In the regenerative receiver the gain (amplification) of a vacuum tube or transistor is increased by using regeneration (positive feedback); some of the energy from the tube's output circuit is fed back into the input circuit with a feedback loop.[10][77][84][85][86] The early vacuum tubes had very low gain (around 5). Regeneration could not only increase the gain of the tube enormously, by a factor of 15,000 or more, it also increased the Q factor of the tuned circuit, decreasing (sharpening) the bandwidth of the receiver by the same factor, improving selectivity greatly.[77][84][85] The receiver had a control to adjust the feedback. The tube also acted as a grid-leak detector to rectify the AM signal.[77]

Another advantage of the circuit was that the tube could be made to oscillate, and thus a single tube could serve as both a beat frequency oscillator and a detector, functioning as a heterodyne receiver to make CW radiotelegraphy transmissions audible.[77][84][85] This mode was called an autodyne receiver. To receive radiotelegraphy, the feedback was increased until it oscillated, then it was tuned to one side of the transmitted signal. The incoming radio carrier signal and local oscillation signal mixed in the tube and produced an audible heterodyne (beat) tone at the difference between the frequencies.

A widely used design was the Armstrong circuit, in which a "tickler" coil in the plate circuit was coupled to the tuning coil in the grid circuit, to provide the feedback.[10][77][86] The feedback was controlled by a variable resistor, or alternately by moving the two windings physically closer together to increase loop gain, or apart to reduce it.[84] This was done by an adjustable air core transformer called a variometer (variocoupler). Regenerative detectors were sometimes also used in TRF and superheterodyne receivers.

One problem with the regenerative circuit was that when used with large amounts of regeneration the selectivity (Q) of the tuned circuit could be too sharp, attenuating the AM sidebands, thus distorting the audio modulation.[87] This was usually the limiting factor on the amount of feedback that could be employed.

A more serious drawback was that it could act as an inadvertent radio transmitter, producing interference (RFI) in nearby receivers.[10][77][84][85][86][88] In AM reception, to get the most sensitivity the tube was operated very close to instability and could easily break into oscillation (and in CW reception did oscillate), and the resulting radio signal was radiated by its wire antenna. In nearby receivers, the regenerative's signal would beat with the signal of the station being received in the detector, creating annoying heterodynes, (beats), howls and whistles.[10] Early regeneratives which oscillated easily were called "bloopers", and were made illegal in Europe. One preventative measure was to use a stage of RF amplification before the regenerative detector, to isolate it from the antenna.[77][84] But by the mid 1920s "regens" were no longer sold by the major radio manufacturers.[10]

Superregenerative receiver

This was a receiver invented by Edwin Armstrong in 1922 which used regeneration in a more sophisticated way, to give greater gain.[78][89][90][91][92] It was used in a few shortwave receivers in the 1930s, and is used today in a few cheap high frequency applications such as walkie-talkies and garage door openers.

In the regenerative receiver the loop gain of the feedback loop was less than one, so the tube (or other amplifying device) did not oscillate but was close to oscillation, giving large gain.[89] In the superregenerative receiver, the loop gain was made equal to one, so the amplifying device actually began to oscillate, but the oscillations were interrupted periodically.[78][93] This allowed a single tube to produce gains of over 106.

Tuned radio frequency (TRF) receiver

Block diagram of a tuned radio frequency receiver. The dotted line indicates that the bandpass filters must be tuned together.
Typical 5 tube TRF circuit from 1924 has 2 stages of RF amplification, a grid-leak detector stage, and 2 stages of transformer-coupled audio amplification
Atwater-Kent TRF receiver from the 1920s with 2 RF stages (left), detector and two audio amplifier tubes (right). The loudspeaker consists of an earphone coupled to an acoustic horn which amplifies the sound.
Tuning a Neutrodyne TRF receiver with 3 tuned circuits (large knobs)

The tuned radio frequency (TRF) receiver, invented in 1916 by Ernst Alexanderson, improved both sensitivity and selectivity by using several stages of amplification before the detector, each with a tuned circuit, all tuned to the frequency of the station.[10][78][93][94][95] It was very popular in quality radios during the 1920s until the superheterodyne replaced it in the 1930s. The TRF receiver consisted of these parts:

A major problem of early TRF receivers was that they were complicated to tune, because each resonant circuit had to be adjusted to the frequency of the station before the radio would work.[10][78] In later TRF receivers the tuning capacitors were linked together mechanically ("ganged") on a common shaft so they could be adjusted with one knob, but in early receivers the frequencies of the tuned circuits could not be made to "track" well enough to allow this, and each tuned circuit had its own tuning knob.[93][96] Therefore, the knobs had to be turned simultaneously. For this reason most TRF sets had no more than three tuned RF stages.[77][87]

A second problem was that the multiple radio frequency stages, all tuned to the same frequency, were prone to oscillate,[96][97] and the parasitic oscillations mixed with the radio station's carrier in the detector, producing audible heterodynes (beat notes), whistles and moans, in the speaker.[10][77][78][95] This was solved by the invention of the Neutrodyne circuit (below) and the development of the tetrode later around 1930, and better shielding between stages.[95]

Today the TRF design is used in a few integrated (IC) receiver chips. From the standpoint of modern receivers the disadvantage of the TRF is that the gain and bandwidth of the tuned RF stages are not constant but vary as the receiver is tuned to different frequencies.[97] Since the bandwidth of a filter with a given Q is proportional to the frequency, as the receiver is tuned to higher frequencies its bandwidth increases.[98][99]

Neutrodyne receiver

Main article: Neutrodyne

The Neutrodyne receiver, invented in 1922 by Louis Hazeltine,[100][101] was a TRF receiver with a "neutralizing" circuit added to each radio amplification stage to cancel the feedback to prevent the oscillations which caused the annoying whistles in the TRF.[10][78][95][96][102] In the neutralizing circuit a capacitor fed a feedback current from the plate circuit to the grid circuit which was 180° out of phase with the feedback which caused the oscillation, canceling it.[77] The Neutrodyne was popular until the advent of cheap tetrode tubes around 1930.

Reflex receiver

Main article: Reflex receiver
Block diagram of simple single tube reflex receiver

The reflex receiver, invented in 1914 by Wilhelm Schloemilch and Otto von Bronk,[103] and rediscovered and extended to multiple tubes in 1917 by Marius Latour[103][104] and William H. Priess, was a design used in some inexpensive radios of the 1920s[105] which enjoyed a resurgence in small portable tube radios of the 1930s[106] and again in a few of the first transistor radios in the 1950s.[78][107] It is another example of an ingenious circuit invented to get the most out of a limited number of active devices. In the reflex receiver the RF signal from the tuned circuit is passed through one or more amplifying tubes or transistors, demodulated in a detector, then the resulting audio signal is passed again though the same amplifier stages for audio amplification.[78] The separate radio and audio signals present simultaneously in the amplifier do not interfere with each other since they are at different frequencies, allowing the amplifying tubes to do "double duty". In addition to single tube reflex receivers, some TRF and superheterodyne receivers had several stages "reflexed".[107] Reflex radios were prone to a defect called "play-through" which meant that the volume of audio did not go to zero when the volume control was turned down.[107]

Superheterodyne receiver

Block diagram of a superheterodyne receiver
The first superheterodyne receiver built at Armstrong's Signal Corps laboratory in Paris during World War I. It is constructed in two sections, the mixer and local oscillator (left) and three IF amplification stages and a detector stage (right). The intermediate frequency was 75 kHz.
During the 1940s the vacuum tube superheterodyne receiver was refined into a cheap-to-manufacture form called the "All American Five" because it only required 5 tubes, which was used in almost all broadcast radios until the end of the tube era in the 1970s.
Modern superheterodyne clock radio
How a superheterodyne works. The incoming radio signal (RF) from the antenna consists of a carrier frequency (dark blue) with sidebands (light blue) on either side containing the modulation. Mixing this with the local oscillator signal (LO), creates a heterodyne intermediate frequency (IF) at the difference between these frequencies. This is bandpass filtered in the IF amplifier, and the demodulator extracts the modulation (M). Because the Image frequency when mixed with the LO also creates a signal at the IF, the RF image rejection filter on the input of the receiver filters out any radio signal at the image frequency.

The superheterodyne, invented in 1918 during World War 1 by Edwin Armstrong[108] when he was in the Signal Corps, is the design used in almost all modern receivers, except a few specialized applications.[64][93][109] It is a more complicated design than the other receivers above, and when it was invented required 6 - 9 vacuum tubes, putting it beyond the budget of most consumers, so it was initially used mainly in commercial and military communication stations.[110] However, by the 1930s the "superhet" had replaced all the other receiver types above.

In the superheterodyne, the "heterodyne" technique invented by Reginald Fessenden is used to shift the frequency of the radio signal down to a lower "intermediate frequency" (IF), before it is processed.[98][110][111][112] An unmodulated sinusoidal signal fLO generated by a local oscillator (LO) is mixed with the incoming radio signal fRF from the antenna in a nonlinear vacuum tube or transistor called the "mixer". The result at the output of the mixer is a heterodyne or beat frequency at the difference between these two frequencies: fIF = |fRF  fLO| This lower frequency is called the intermediate frequency (IF). The IF also contains the modulation (sidebands) that was present in the original RF signal. This signal is amplified and bandpass filtered as in the TRF receiver,[93] then is demodulated in a detector, producing an audio signal.

The superheterodyne design is superior to other receivers for these reasons:[98][99]

A problem with superhet receivers is that when the incoming radio signal fRF is mixed with the local oscillator signal fLO, two new frequencies (heterodynes) are created,[112] one at the sum fRF + fLO, and one at the difference fRF  fLO of the frequencies. Because of this, the receiver can receive incoming RF signals at two different frequencies,[99][109][112][113] one above the LO frequency: fRF1 = fLO + fIF, and one below the LO frequency: fRF2 = fLO  fIF. The receiver can be designed to receive on either of these two frequencies; the former is called low-side injection because the LO signal frequency is below the received frequency, while the latter is high-side injection.[112] Whichever is chosen, the other frequency is called the image frequency. If the receiver is receiving a signal on one of these frequencies, for example fRF1, any other radio station or radio noise on the other frequency fRF2 will be received also, interfering with the desired signal. Therefore, the superheterodyne requires a bandpass filter on the input to reject this image frequency.[109] This image rejection filter does not need great selectivity, but as the receiver is tuned to different frequencies it must "track" in tandem with the LO.

Double conversion superheterodyne block diagram

Double-conversion superheterodyne: In choosing the intermediate frequency (IF) used in a superhet, there is a tradeoff between image rejection and selectivity.[109][112] Since the separation between the desired frequency and the image is 2fIF, the higher the IF, the farther apart these two frequencies are, and the better the image rejection. However, the lower the IF, the narrower the bandwidth the IF filter can achieve, and the better the selectivity. In order to achieve both good image rejection and selectivity, many modern superhet receivers use two intermediate frequencies; this is called a dual-conversion or double-conversion superheterodyne. The incoming RF signal is first mixed with one local oscillator signal in the first mixer to convert it to a high IF frequency, to allow efficient filtering out of the image frequency, then this first IF is mixed with a second local oscillator signal in a second mixer to convert it to a low IF frequency for good bandpass filtering. Some receivers even use triple-conversion.

Terminology used with superheterodyne receivers:

To receive radiotelegraph (CW) or single-sideband modulation (SSB), a beat frequency oscillator (BFO) is used.

Semiconductor era

A modern smartphone has several digital radio transmitters and receivers to connect to different devices; a cellular receiver, a wireless modem, a bluetooth modem, and a GPS receiver

The invention of the transistor in 1947 revolutionized radio technology, making truly portable receivers possible, beginning with transistor radios in the late 1950s. Although portable vacuum tube radios were made, tubes were bulky and inefficient, consuming large amounts of power and requiring several large batteries to produce the filament and plate voltage. Transistors did not require a heated filament, reducing power consumption, and were smaller and much less fragile than vacuum tubes.

The development of integrated circuits (ICs) in the 1970s created another revolution, allowing an entire radio receiver to be put on a chip. ICs reversed the economics of vacuum tube radios; since the marginal cost of adding additional amplifying devices (transistors) to the chip was essentially zero, the size and cost of the receiver was dependent not on the active components as with vacuum tubes, but on the passive components; inductors and capacitors, which could not be integrated easily on the chip.[4] As a result, the current trend in receivers is to use digital circuitry on the chip to do functions that were formerly done by analog circuits which require passive components. In a digital receiver the IF signal is sampled and digitized, and the bandpass filtering and detection functions are performed by digital signal processing (DSP) on the chip. Another benefit of DSP is that the properties of the receiver; channel frequency, bandwidth, gain, etc. can be dynamically changed by software to react to changes in the environment; these systems are known as software-defined radios or cognitive radio.

In modern wireless technology, radio transmitters and receivers are embedded in portable digital devices such as laptops, cell phones, GPS receivers, Bluetooth headsets, wireless routers and work automatically, in the background, to keep the device in touch with other devices, without wires. They transmit binary digital data by modulation methods such as frequency shift keying (FSK) allowing portable digital devices to communicate via wireless networks.

Digital technologies

Many of the functions performed by analogue electronics can be performed by software instead. The benefit is that software is not affected by temperature, physical variables, electronic noise and manufacturing defects.[114] For really high-performance receivers, such as satellite communications receivers and military/naval receivers, two-stage ("double conversion") and even three-stage ("triple conversion") superheterodyne processing is frequently used. Single-conversion receivers are rather simple-minded in their nature.

DSP technology

DSP technology, short for digital signal processing, is the use of digital means to process signals and is coming into wide use in modern shortwave receivers. It is the basis of many areas of modern technology including cell phones, CD players, video recorders and computers. A digital signal is essentially a stream or sequence of numbers that relay a message through some sort of medium such as a wire. The primary benefit of DSP hardware in shortwave receivers is the ability to tailor the bandwidth of the receiver to current reception conditions and to the type of signal being listened to. A typical analog only receiver may have a limited number of fixed bandwidths, or only one, but a DSP receiver may have 40 or more individually selectable filters.

PC controlled radio receivers

"PC radios", or radios that are designed to be controlled by a standard PC are controlled by specialized PC software using a serial port connected to the radio. A "PC radio" may not have a front-panel at all, and may be designed exclusively for computer control, which reduces cost.

Some PC radios have the great advantage of being field upgradable by the owner. New versions of the DSP firmware can be downloaded from the manufacturer's web site and uploaded into the flash memory of the radio. The manufacturer can then in effect add new features to the radio over time, such as adding new filters, DSP noise reduction, or simply to correct bugs.

A full-featured radio control program allows for scanning and a host of other functions and, in particular, integration of databases in real-time, like a "TV-Guide" type capability. This is particularly helpful in locating all transmissions on all frequencies of a particular broadcaster, at any given time. Some control software designers have even integrated Google Earth to the shortwave databases, so it is possible to "fly" to a given transmitter site location with a click of a mouse. In many cases the user is able to see the transmitting antennas where the signal is originating from.

Radio control software

The field of software control of PC radios has grown rapidly in the last several years, with developers making a number of advances. Since the Graphical User Interface or GUI interface PC to the radio has unlimited flexibility, any number of new features can be added by the software designer. Features that can be found in advanced control software programs today include a band table, GUI controls corresponding to traditional radio controls, local time clock and a UTC clock, signal strength meter, an ILG database for shortwave listening with lookup capability, scanning capability, text-to-speech interface, and integrated Conference Server.

Software-defined radios

The next level in radio / software integration are so-called pure "software defined radios". The distinction here is that all filtering, modulation and signal manipulation is done in software, usually by a PC soundcard or by a dedicated piece of DSP hardware. There may be a minimal RF front-end or traditional radio that supplies an IF to the SDR. SDR's can go far beyond the usual demodulation capability of typical, and even high-end DSP shortwave radios. They can for example, record large swaths of the radio spectrum to a hard drive for "playback" at a later date. The same SDR that one minute is demodulating a simple AM broadcast may also be able to decode an HDTV broadcast in the next. A well known open-source project called GNU Radio is dedicated to evolving a high-performance SDR. All the source code for this SDR is freely downloadable and modifiable by anyone.

See also

Wikimedia Commons has media related to Radio receivers.

Notes

  1. Radio-Electronics, Radio Receiver Technology
  2. "ALMA Telescope Upgrade to Power New Science". ESO Announcement. Retrieved 5 June 2012.
  3. The Radio Guide, Types of Portable Radios
  4. 1 2 3 4 5 6 7 8 9 10 11 12 13 Lee, Thomas H. (2004). The Design of CMOS Radio-Frequency Integrated Circuits, 2nd Ed. UK: Cambridge University Press. pp. 1–8. ISBN 0521835399.
  5. 1 2 3 4 5 Phillips, Vivian J. (1980). Early Radio Wave Detectors. London: Inst. of Electrical Engineers. pp. 4–12. ISBN 0906048249.
  6. 1 2 Rudersdorfer, Ralf (2013). Radio Receiver Technology: Principles, Architectures and Applications. John Wiley and Sons. pp. 1–2. ISBN 111864784X.
  7. Nahin, Paul J. (2001). The Science of Radio: With Matlab and Electronics Workbench Demonstration, 2nd Ed. Springer Science & Business Media. pp. 45–48. ISBN 0387951504.
  8. 1 2 3 4 5 6 7 8 9 10 Coe, Lewis (2006). Wireless Radio: A History. McFarland. pp. 3–8. ISBN 0786426624.
  9. 1 2 3 4 5 6 7 8 9 10 McNicol, Donald (1946). Radio's Conquest of Space. Murray Hill Books. pp. 57–68.
  10. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Carr, Joseph (1990). Old Time Radios! Restoration and Repair. McGraw-Hill Professional. pp. 5–13. ISBN 0071507663.
  11. 1 2 3 Beauchamp, Ken (2001). History of Telegraphy. IET. pp. 184–186. ISBN 0852967926.
  12. 1 2 3 4 Nahin, Paul J. (2001) The Science of Radio, p. 53-56
  13. 1 2 3 4 5 6 7 8 9 10 11 12 Klooster, John W. (2007). Icons of Invention. ABC-CLIO. pp. 159–161. ISBN 0313347433.
  14. McNicol, Donald (1946). Radio's Conquest of Space. Murray Hill Books. pp. 37–45.
  15. Hong, Sungook (2001). Wireless: From Marconi's Black-box to the Audion. MIT Press. pp. 1–2. ISBN 0262082985.
  16. 1 2 3 4 5 6 7 8 9 Sarkar et al (2006) History of Wireless, p. 349-358, archive
  17. 1 2 3 Fleming, John Ambrose (1910). The Principles of Electric Wave Telegraphy and Telephony, 2nd Ed. London: Longmans, Green and Co. pp. 420–428.
  18. 1 2 3 4 Stone, Ellery W. (1919). Elements of Radiotelegraphy. D. Van Nostrand Co. pp. 203–208.
  19. 1 2 3 McNicol, Donald (1946) Radio's Conquest of Space, p. 107-113
  20. Maver, William Jr. (August 1904). "Wireless Telegraphy To-Day". American Monthly Review of Reviews (New York: The Review of Reviews Co.) 30 (2): 192. Retrieved January 2, 2016.
  21. Aitken, Hugh G.J. (2014). The Continuous Wave: Technology and American Radio, 1900-1932. Princeton Univ. Press. p. 190. ISBN 1400854601.
  22. 1 2 3 4 Marriott, Robert H. (September 17, 1915). "United States Radio Development". Proc. of the Inst. of Radio Engineers (US: Institute of Radio Engineers) 5 (3): 184. doi:10.1109/jrproc.1917.217311. Retrieved 2010-01-19.
  23. Secor, H. Winfield (January 1917). "Radio Detector Development". Electrical Experimenter (New York: Experimenter Publishing Co.) 4 (9): 652–656. Retrieved January 3, 2016.
  24. McNicol, Donald (1946). Radio's Conquest of Space. Murray Hill Books. pp. 121–123.
  25. 1 2 3 4 5 6 Stone, Ellery (1919) Elements of Radiotelegraphy, p. 209-221
  26. Fleming, John Ambrose (1910) The Principles of Electric Wave Telegraphy and Telephony, p. 446-455
  27. McNicol, Donald (1946) Radio's Conquest of Space, p. 115-119
  28. Fleming, John Ambrose (1910) The Principles of Electric Wave Telegraphy and Telephony, p. 460-464
  29. 1 2 3 4 5 Lee, Thomas H. (2004) The Design of CMOS Radio Frequency Integrated Circuits, 2nd Ed., p. 9-11
  30. McNicol, Donald (1946) Radio's Conquest of Space, p. 157-162
  31. Fleming, John Ambrose (1910) The Principles of Electric Wave Telegraphy and Telephony, p. 476-483
  32. McNicol, Donald (1946) Radio's Conquest of Space, p. 123-131
  33. Fleming, John Ambrose (1910) The Principles of Electric Wave Telegraphy and Telephony, p. 471-475
  34. 1 2 3 4 5 6 Hong, Sungook (2001). Wireless: From Marconi's Black-box to the Audion. MIT Press. pp. 89–100. ISBN 0262082985.
  35. 1 2 Aitken, Hugh 2014 Syntony and Spark: The origins of radio, p. 70-73
  36. 1 2 3 Beauchamp, Ken (2001) History of Telegraphy, p. 189-190
  37. 1 2 Kennelly, Arthur E. (1906). Wireless Telegraphy: An Elementary Treatise. New York: Moffatt, Yard and Co. pp. 173–183.
  38. Aitken, Hugh 2014 Syntony and Spark: The origins of radio, p. 31-48
  39. Crookes, William (February 1, 1892). "Some Possibilities of Electricity". The Fortnightly Review (London: Chapman and Hall) 51: 174–176. Retrieved August 19, 2015.
  40. 1 2 3 4 5 6 7 Rockman, Howard B. (2004). Intellectual Property Law for Engineers and Scientists. John Wiley and Sons. pp. 196–199. ISBN 0471697397.
  41. 1 2 3 4 5 Aitken, Hugh G.J. (2014). Syntony and Spark: The Origins of Radio. Princeton Univ. Press. pp. 253–255, 259. ISBN 1400857880.
  42. Coe, Lewis (2006). Wireless Radio: A History. McFarland. pp. 111–113. ISBN 0786426624.
  43. Smith, Craig B. (2008). Lightning: Fire from the Sky. Dockside Consultants Inc. ISBN 0-615-24869-1.
  44. Regal, Brian (2005). Radio: The Life Story of a Technology. Greenwood Publishing Group. pp. 21–23. ISBN 0313331677.
  45. 1 2 McNicol, Donald (1946) Radio's Conquest of Space, p. 242-253
  46. 1 2 Marx, Harry J.; Van Muffling, Adrian (1922). Radio Reception. New York: G. Putnam's Sons. pp. 95–103.
  47. 1 2 Fleming, John Ambrose (1910). The Principles of Electric Wave Telegraphy and Telephony, 2nd Ed. London: Longmans, Green and Co. pp. 580–582, 586.
  48. US Patent No. 645576, Nikola Tesla, System of transmission of electrical energy, filed September 2, 1897; granted March 20, 1900
  49. US Patent no. 609,154 Oliver Joseph Lodge, Electric Telegraphy, filed: February 1, 1898, granted: August 16, 1898
  50. US Patent no. 714,756, John Stone Stone Method of electric signaling, filed: February 8, 1900, granted: December 2, 1902
  51. Pechenkin, Alexander (2013). Leonid Isaakovich Mandelstam: Research, Teaching, Life. Springer Science and Business Media. pp. 34–36. ISBN 3319005723.
  52. US Patent no. 763,772, Guglielmo Marconi, Apparatus for wireless telegraphy, filed: November 10, 1900, granted: June 28, 1904. Corresponding British patent no. 7777, Guglielmo Marconi, Improvements in apparatus for wireless telegraphy, filed: April 26, 1900, granted: April 13, 1901
  53. 1 2 3 4 5 McNicol, Donald (1946) Radio's Conquest of Space, p. 254-259
  54. Terman, Frederick E. (1943). Radio Engineers' Handbook (PDF). New York: McGraw-Hill Book Co. p. 170.
  55. 1 2 Basalla, George (1988). The Evolution of Technology. UK: Cambridge University Press. p. 44. ISBN 0-521-29681-1.
  56. Corbin, Alfred (2006). The Third Element: A Brief History of Electronics. AuthorHouse. pp. 44–45. ISBN 1-4208-9084-0.
  57. Army Technical Manual TM 11-665: C-W and A-M Radio Transmitters and Receivers. US Dept. of the Army. 1952. pp. 167–169.
  58. 1 2 3 Williams, Lyle Russell (2006). The New Radio Receiver Building Handbook. Lulu. pp. 20–24. ISBN 1847285260.
  59. Beauchamp, Ken (2001). History of Telegraphy. Institution of Electrical Engineers. p. 191. ISBN 0852967926.
  60. Bucher, Elmer Eustice (1917). Practical Wireless Telegraphy. New York: Wireless Press. p. 306.
  61. Lescarboura, Austin C. (1922). Radio for Everybody. New York: Scientific American Publishing Co. pp. 93–94.
  62. 1 2 3 Lauer, Henri; Brown, Harry L. (1920). Radio Engineering Principles. McGraw-Hill. pp. 135–142.
  63. 1 2 3 4 5 McNicol, Donald (1946). Radio's Conquest of Space. New York: Murray Hill Books. pp. 133–136.
  64. 1 2 3 4 5 Lee, Thomas H. (2004) The Design of CMOS Radio Frequency Integrated Circuits, 2nd Ed., p. 14-15
  65. US patent no. 1050441, Reginald A. Fessenden, Electrical signaling apparatus, filed July 27, 1905; granted January 14, 1913
  66. Hogan, John V. L. (April 1921). "The Heterodyne Receiver". The Electric Journal (Pittsburgh, USA: The Electric Journal) 18 (4): 116–119. Retrieved January 28, 2016.
  67. Nahin, Paul J. (2001) The Science of Radio, p. 91
  68. McNicol, Donald (1946) Radio's Conquest of Space, p. 267-270
  69. 1 2 3 McNicol, Donald (1946) Radio's Conquest of Space, p. 341-344
  70. 1 2 3 4 5 Wurtzler, Steve J. (2007). Electric Sounds: Technological Change and the Rise of Corporate Mass Media. Columbia Univ. Press. pp. 147–148. ISBN 023151008X.
  71. 1 2 3 Nebeker, Frederik (2009). Dawn of the Electronic Age: Electrical Technologies in the Shaping of the Modern World, 1914 to 1945. John Wiley and Sons. pp. 159–160. ISBN 0470409746.
  72. McNicol, Donald (1946) Radio's Conquest of Space, p. 336-340
  73. Terman, Frederick E. (1943) Radio Engineers' Handbook, p. 656
  74. Malanowski, Gregory (2011). The Race for Wireless. AuthorHouse. p. 67. ISBN 1463437501.
  75. Nelson, Phillip I. (1995). "Powering your antique battery radio". Phil's Old Radios. Personal website. Retrieved January 1, 2016.
  76. Haan, E. R. (December 1925). "Radio batteries, their care and selection". Popular Mechanics (New York: Popular Mechanics Co.) 44 (6): 1010–1013. ISSN 0032-4558. Retrieved January 1, 2016.
  77. 1 2 3 4 5 6 7 8 9 10 11 12 13 Williams, Lyle Russell (2006). The New Radio Receiver Building Handbook. Lulu. pp. 24–27. ISBN 1847285260.
  78. 1 2 3 4 5 6 7 8 9 10 Lee, Thomas H. (2004) The Design of CMOS Radio Frequency Integrated Circuits, 2nd Ed., p. 15-18
  79. De Forest, Lee (January 1906). "The Audion; A New Receiver for Wireless Telegraphy". Trans. of the AIEE (American Institute of Electrical and Electronic Engineers) 25: 735–763. doi:10.1109/t-aiee.1906.4764762. Retrieved January 7, 2013. The link is to a reprint of the paper in the Scientific American Supplement, No. 1665, November 30, 1907, p.348-350, copied on Thomas H. White's United States Early Radio History website
  80. Terman, Frederick E. (1943). Radio Engineers' Handbook (PDF). New York: McGraw-Hill Book Co. pp. 564–565.
  81. 1 2 3 Langmuir, Irving (September 1915). "The Pure Electron Discharge and its Applications in Radio Telegraphy and Telephony" (PDF). Proceedings of the IRE (New York: Institute of Radio Engineers) 3 (3): 261–293. Retrieved January 12, 2016.
  82. Armstrong, Edwin H. (September 1915). "Some recent developments in the Audion receiver" (PDF). Proc. of the IRE (New York: Institute of Radio Engineers) 3 (9): 215247. Retrieved August 29, 2012.
  83. Armstrong, Edwin H. (April 1921). "The Regenerative Circuit". The Electrical Journal (Pittsburgh, PA: Westinghouse Co.) 18 (4): 153–154. Retrieved January 11, 2016.
  84. 1 2 3 4 5 6 Army Technical Manual TM 11-665: C-W and A-M Radio Transmitters and Receivers, 1952, p. 187-190
  85. 1 2 3 4 Terman, Frederick E. (1943) Radio Engineers' Handbook, p. 574-575
  86. 1 2 3 McNicol, Donald (1946) Radio's Conquest of Space, p. 260-262
  87. 1 2 Langford-Smith, F. (1953). Radiotron Designer's Handbook, 4th Ed. (PDF). Wireless Press for RCA. pp. 1223–1224.
  88. In the early 1920s Armstrong, David Sarnoff head of RCA, and other radio pioneers testified before the US Congress on the need for legislation against radiating regenerative receivers. Wing, Willis K. (October 1924). "The Case Against the Radiating Receiver" (PDF). Broadcast Radio (New York: Doubleday, Page and Co.) 5 (6): 478–482. Retrieved January 16, 2016.
  89. 1 2 Army Technical Manual TM 11-665: C-W and A-M Radio Transmitters and Receivers, 1952, p. 190-193
  90. Terman, Frederick E. (1943). Radio Engineers' Handbook (PDF). New York: McGraw-Hill Book Co. pp. 662–663.
  91. Williams, Lyle Russell (2006) The New Radio Receiver Building Handbook, p. 31-32
  92. McNicol, Donald (1946) Radio's Conquest of Space, p. 279-282
  93. 1 2 3 4 5 6 7 8 Dixon, Robert (1998). Radio Receiver Design. CRC Press. pp. 57–61. ISBN 0824701615.
  94. Army Technical Manual TM 11-665: C-W and A-M Radio Transmitters and Receivers, 1952, p. 170-175
  95. 1 2 3 4 McNicol, Donald (1946) Radio's Conquest of Space, p. 263-267
  96. 1 2 3 Army Technical Manual TM 11-665: C-W and A-M Radio Transmitters and Receivers, 1952, p. 177-179
  97. 1 2 Terman, Frederick E. (1943). Radio Engineers' Handbook (PDF). New York: McGraw-Hill Book Co. pp. 438–439.
  98. 1 2 3 4 5 6 Army Technical Manual TM 11-665: C-W and A-M Radio Transmitters and Receivers, 1952, p. 195-197
  99. 1 2 3 Rembovsky, Anatoly; Ashikhmin, Alexander; Kozmin, Vladimir; et al. (2009). Radio Monitoring: Problems, Methods and Equipment. Springer Science and Business Media. p. 26. ISBN 0387981004.
  100. US Patent No. 1450080, Louis Alan Hazeltine, "Method and electric circuit arrangement for neutralizing capacity coupling"; filed August 7, 1919; granted March 27, 1923
  101. Hazeltine, Louis A. (March 1923). "Tuned Radio Frequency Amplification With Neutralization of Capacity Coupling" (PDF). Proc. of the Radio Club of America (New York: Radio Club of America) 2 (8): 7–12. Retrieved March 7, 2014.
  102. Terman, Frederick E. (1943). Radio Engineers' Handbook (PDF). New York: McGraw-Hill Book Co. pp. 468–469.
  103. 1 2 Grimes, David (May 1924). "The Story of Reflex and Radio Frequency" (PDF). Radio in the Home 2 (12): 9–10,. Retrieved January 24, 2016.
  104. US Patent no. 1405523, Marius Latour Audion or lamp relay or amplifying apparatus, filed December 28, 1917; granted February 7, 1922
  105. McNicol, Donald (1946) Radio's Conquest of Space, p. 283-284
  106. "Reflexing Today: Operating economy with the newer tubes" (PDF). Radio World (New York: Hennessey Radio Publications Co.) 23 (17): 3. July 8, 1933. Retrieved January 16, 2016.
  107. 1 2 3 Langford-Smith, F. (1953). Radiotron Designer's Handbook, 4th Ed. (PDF). Wireless Press for RCA. pp. 1140–1141.
  108. Armstrong, Edwin H. (February 1921). "A new system of radio frequency amplification". Proceedings of the Inst. of Radio Engineers (New York: Institute of Radio Engineers) 9 (1): 3–11. Retrieved December 23, 2015.
  109. 1 2 3 4 5 Williams, Lyle Russell (2006) The New Radio Receiver Building Handbook, p. 28-30
  110. 1 2 McNicol, Donald (1946) Radio's Conquest of Space, p. 272-278
  111. Terman, Frederick E. (1943) Radio Engineers' Handbook, p. 636-638
  112. 1 2 3 4 5 Carr, Joseph J. (2001). The Technician's Radio Receiver Handbook: Wireless and Telecommunication Technology. Newnes. pp. 8–11. ISBN 0750673192.
  113. Terman, Frederick E. (1943) Radio Engineers' Handbook, p. 645
  114. "History of the Radio Receiver". Radio-Electronics.Com. Retrieved 2007-11-23.

Further reading

This article is issued from Wikipedia - version of the Wednesday, May 04, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.