Regency TR-1

Regency TR-1 transistor radio

The Regency TR-1 was the first commercially manufactured transistor radio. First sold in 1954, it was a novelty due to small size and portability; about 150,000 units were sold despite mediocre performance. The device demonstrated the use of transistors for consumer electronics; previously transistors had only been used in military or industrial applications. Surviving specimens are sought out by collectors.

History

Two companies—Texas Instruments of Dallas, Texas, and Industrial Development Engineering Associates (I.D.E.A.) of Indianapolis, Indiana—worked together to produce the Regency TR-1. Previously, Texas Instruments produced instrumentation for the oil industry and locating devices for the U.S. Navy—and I.D.E.A. built home television antenna boosters. The two companies worked together on the TR-1 to grow revenues for their respective companies by pioneering this new product area.[1]

In May 1954, Texas Instruments had designed and built a prototype transistor radio and was looking for an established radio manufacturer to develop and market a radio using their transistors. No major radio maker, including RCA, Philco, and Emerson, was interested. The President of I.D.E.A. at the time, Ed Tudor, jumped at the opportunity to manufacture the TR-1, predicting sales of the transistor radios would be "20 million radios in three years."[2] The Regency Division of I.D.E.A announced the TR-1 on October 18, 1954, and put it on sale in November 1954. It was the first practical transistor radio made in significant numbers.

One year after the TR-1 release, sales approached 100,000 units. The look and size of the TR-1 were well received, but reviews of its performance were typically adverse.[3] The Regency TR-1 is patented by Richard C. Koch, US 2892931 , former Project Engineer of I.D.E.A.

The Regency TR-1 circuitry was refined from the Texas Instruments prototype, reducing the number of parts, including two expensive transistors. Though this severely reduced the audio output volume, it let I.D.E.A. sell the radio for only a small profit. The initial TR-1 retail price was $49.95 (roughly $400 in year-2010 dollars) and it sold about 150,000 units.

The TR-1 used Texas Instruments' NPN transistors, hand-picked in sets of four. A 22.5 volt battery provided power, since the only way to get adequate radio frequency performance out of early transistors was to run them close to their collector-to-emitter breakdown voltage. The current drain from this battery was only 4 mA,[4] allowing 20 to 30 hours of operation, in comparison to only several hours for the portable receivers based on vacuum tubes.[5] Such battery consumption rate still made the TR-1 rather expensive to run.

While the radio was praised for novelty and small size, the sensitivity and sound quality were behind the tube-based competitors. A review in Consumer Reports mentions the high level of noise and instability on certain radio frequencies, recommending against the purchase.[5]

Design

I.D.E.A. outsourced the TR-1 exterior design to the industrial design firm of Painter, Teague and Petertil. The design was created within six weeks by way of telephone and design sketches exchanged by mail. The design won an award from the Industrial Design Society of New York and was selected by the Museum of Modern Art for the American Art and Design Exhibition in Paris in 1955.[6]

The TR-1 was initially offered in black, bone white, mandarin red, and cloud gray. It was later uncommonly offered in olive green and mahogany. Other later, rare colors included lavender, pearl white, turquoise, pink, and lime. It was advertised as being 3" x 5" x 1.25" and weighed 12 ounces including the 22.5 volt battery. It came in a cardboard box with the color stamped on the end. An optional earphone sold for $7.50.[7]

The red triangles on the frequency dial mark the CONELRAD frequencies of 640 and 1240 kHz.

Circuit

TR-1, circuit board and casing. Exhibit of Deutsches Museum, Munich
22.5 Volt battery used in the Regency TR-1 (AA battery for comparison shown on left)

The TR-1 was a superheterodyne receiver made [8] with four n-p-n transistors and one diode. It contained a single transistor converter stage, followed by two intermediate-frequency amplifier stages. After detection, a single-transistor stage amplified the sound frequency. All amplifier stages used common emitter amplifiers. Stages were transformer coupled, with tuned transformers for the intermediate frequency amplifiers and a miniature audio transformer for the loudspeaker. The intermediate frequency transformers were paired with capacitors, and hand tuned to the intermediate frequency (262 kHz[4]) using movable cores.

The receiver had automatic gain control. The DC level of the detected signal was filtered with a large capacitor and used to control the gain of the first IF stage (VT2, first after the heterodyne).[9]

The 22.5 V battery, while now uncommon, is still used in some devices and as of 2012 remains available on the market.[10] The minimum required voltage is lower, about 15 V. The electrolytic capacitor is connected in parallel to the battery. It improves stability but would be damaged if the battery is reversed. The power switch was coupled with the volume control.

The initial six-transistor Texas Instruments design used a two-transistor converter stage with a separate oscillator, and a more powerful two-transistor sound amplifier.

Manufacture

Regency began manufacturing the TR-1 on October 25, 1954. The manufacture was a collective effort by manufacturers around the country. The transistors and transformers came from Texas Instruments in Dallas. Capacitors came from International Electronics, Inc. of Nashville,[1] Erie Electronics of Erie, Pennsylvania, and Centralab of Milwaukee, Wisconsin. The speakers came from Jensen in Chicago, Illinois. IF transformers came from Vokar of Dexter, Michigan. The volume control came from the Chicago Telephone Supply in Elkhart, Indiana. The tuning capacitor came from Radio Condenser Co. in Camden, New Jersey. The Richardson Company in Melrose Park, Illinois and Indianapolis supplied the circuit board material to Croname in Chicago, who manufactured the circuit boards. The actual plastic case for the TR-1 was produced by Argus Plastics in Indianapolis, Indiana.[7]

References

  1. 1 2 Smicoe, Robert J. "The Revolution in Your Pocket". Invention & Technology Magazine, Fall 2004, Volume 20, Issue 2. Archived from the original on 2006. Retrieved 2010-04-20.
  2. ↑ David Lane and Robert Lane (1994). Transistor Radios: A Collector's Encyclopedia and Price Guide. Wallace-Homestead Book Company. ISBN 0-87069-712-9. page 3
  3. ↑ David Lane and Robert Lane (1994). Transistor Radios: A Collector's Encyclopedia and Price Guide. Wallace-Homestead Book Company. ISBN 0-87069-712-9. page 4
  4. 1 2 TR-1, The First Transistor Radio Receiver. Technical Data And Service Notes. — Regency Div. I.D.E.A. Inc., Indianapolis, Ind., P. 2
  5. 1 2 Schiffer, M. B. The portable radio in American life. — University of Arizona Press, 1991. — P. 170-178. — 259 p. — ISBN 9780816512843
  6. ↑ Handy, Erbe, Blackham, Antonier (1993). Made In Japan : Transistor Radios of the 1950s and 1960s. Chronicle Books. ISBN 0-8118-0271-X. pages 15–17
  7. 1 2 Reyer, Steve (Dr.) "Regency TR-1 Transistor Radio Facts and Figures". mequonsteve.com, Retrieved December 2, 2012
  8. ↑ Regency schematic
  9. ↑ Lee, T. C. The Design of CMOS Radio-Frequency Integrated Circuits. — Cambridge University Press, 2004. — P. 271-272. — 797 p. — ISBN 9780521835398
  10. ↑ www.batteriesinaflash.com. The sale page of Eveready 412 Carbon Zinc 22.5V Battery NEDA 215, 15F20, BLR122.

Regency TR-1 Transistor Radio History: Web site with many historical references on the web and in published literature

External links

This article is issued from Wikipedia - version of the Monday, February 29, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.