Road roller

"Roller-compactor" redirects here. For other types of rolling compactors, see Compactor.
Caterpillar soil compactor equipped with padfoot drum, being used to compact the ground before placing concrete
An old diesel-powered road roller
Road roller DS-31 (Bieldartehnika JSC )

A road roller (sometimes called a roller-compactor, or just roller) is a compactor type engineering vehicle used to compact soil, gravel, concrete, or asphalt in the construction of roads and foundations, similar rollers are used also at landfills or in agriculture.

In some parts of the world, road rollers are still known colloquially as steam rollers, regardless of their method of propulsion. This typically only applies to the largest examples (used for road-making).

History

Horse-drawn road roller from 1800
Steam-powered roller
Zettelmeyer diesel-powered road roller

The first road rollers were horse-drawn, and were probably just borrowed farm implements (see roller (agricultural tool)).

Main article: steamroller

Since the effectiveness of a roller depends to a large extent on its weight, self-powered vehicles replaced horse-drawn rollers from the mid-19th century. The first such vehicles were steam rollers. Single-cylinder steam rollers were generally used for base compaction and run with high engine revs in a low gear to promote bounce and vibration from the crankshaft through to the rolls in much the same way as a vibrating roller. The double cylinder or compound steam rollers became popular from around 1910 onwards and were used mainly for the rolling of hot-laid surfaces due to their smoother running engines, however both cylinder types are capable of rolling the finished surface. Steam rollers were often dedicated to a task by their gearing as the slower engines were for base compaction whereas the higher geared models were often referred to as 'chip chasers' which followed behind the hot tar and chipping laying machines. Some road companies in the United States used steamrollers through the 1950s, and in the UK, some remained in commercial service until the early 1970s.

As internal combustion engine technology improved during the 20th century, kerosene-, gasoline- (petrol), and diesel-powered rollers gradually replaced their steam-powered counterparts. The first internal-combustion powered road rollers were very similar to the steam rollers they replaced. They used similar mechanisms to transmit power from the engine to the wheels, typically large, exposed spur gears. Some users did not like them in their infancy, as the engines of the era were typically difficult to start, particularly the kerosene-powered ones.

Virtually all road rollers in commercial use now use diesel power.

Uses on a road: Start-to-finish

Road rollers use the weight of the vehicle to compress the surface being rolled (static) or use mechanical advantage (vibrating). Initial compaction of the substrate on a road project is done using a padfoot drum roller, which achieves higher compaction density due to the pads having less surface area. On large freeways a four wheel compactor with padfoot drum and a blade, such as a Caterpillar 815/825 series machine, would be used due to its high weight, speed and the powerful pushing force to spread bulk material. On regional roads a smaller single padfoot drum machine may be used. The next machine is usually a single smooth drum compactor that compacts the high spots down until the soil is smooth, and this is usually done in combination with a motor grader to get a level surface. Sometimes at this stage a pneumatic tyre roller would be used. These rollers feature two rows (front and back) of pneumatic tyres that overlap, and the flexibility of the tyres provides a kneading action that seals the surface and with some vertical movement of the wheels, enables the roller to operate effectively on uneven ground. Once the soil base is flat the pad drum compactor is no longer used on the road surface. The next course (road base) would be compacted using a smooth single drum, smooth tandem roller or pneumatic tyre roller in combination with a grader, and a water truck to achieve the desired flat surface with the right moisture content for optimum compaction. Once the road base is compacted, the smooth single drum compactor is no longer used on the road surface (There is however an exception, if the single drum has special flat-wide-base tyres on the machine). The final wear course of asphalt concrete (a.k.a. asphalt or blacktop in North America, or macadam in England) is laid using a paver and compacted using a tandem smooth drum roller, a three-point roller or a pneumatic tyre roller. Three point rollers on asphalt were very common once and are still used, but tandem vibrating rollers are the usual choice now, with the pneumatic tyre roller's kneading action being the last roller to seal off the surface.

Rollers are also used in landfill compaction. Such compactors typically have padfoot or "sheep's-foot" drums, and do not achieve a smooth surface. The pads aid in compression, due to the smaller area contacting the ground.

Configurations

Flattened and leveled construction site with road roller in the background

The roller can be a simple drum with a handle that is operated by one person, and weighs 100 pounds, or as large as a ride-on road roller weighing 22 short tons (44,000 lb or 20 tonnes) and costing more than US$150,000. A landfill unit may weigh 59 short tons (54 tonnes).

Roller types

Pedestrian operated

Ride-on smooth finish

Ride-on soil/landfill compactor with pads/feet/spikes

Other

Drum types

Drums are available in widths ranging from 24 to 84 inches (0.6 to 2 metres).

Tyre roller types

Tyre rollers are available in widths ranging up to 2.7 metres (8.9 ft), with between 7 and 11 wheels (e.g. 3 wheels at front, 4 at back): 7 and 8 wheel types are normally used in Europe and Africa; 9 and 11 in America; and any type in Asia. Very heavy tyre rollers are used to compact soil.

Variations and features

Gallery

Manufacturers

  • ABG (Germany) — SD/TD (purchased by Ingersoll Rand and now part of Volvo CE)
  • AGICO
  • Albaret (Germany) — PT (now part of Caterpillar)
  • Ammann Group (Switzerland)
  • Atlas (Germany) — SD
  • Aveling-Barford (England) — TD/PT/3P
  • Britannia Engineering Ltd. (India)
  • Benford (England) — SD/TD (purchased by Terex)
  • Bitelli (Italy) — SD/TD/PT (now part of Caterpillar)
  • Blaw Knox (England) -TD/PT (known for pavers, but also had roller models)
  • BOM-MACH (South Africa)
  • BOMAG (Germany) — SD/TD/PT (BOMAG/HYPAC in the USA market)
  • Buffalo-Springfield Roller Company (USA) (purchased by Kohring and eventually Bomag in the USA)
  • Case CE (USA) — SD (brands the Ammann/Sta machines as Case in the USA
  • Caterpillar Inc. (USA) — SD/TD/PT (has the former lines of RAYGO, BROS and Bitelli
  • Coates (Australia) — TD (disbanded)
  • CORINSA (SPAIN) — PT/TD
  • CMI-Terex (USA) — 3P (has the former lines of REX and Benford)
  • Davelco (Australia) — TD (disbanded)
  • Dynapac (Sweden) — SD/TD/PT/3P (now part of Atlas Copco)
  • Galion
  • GEMCO
  • Hamm AG (Germany) — SD/TD/PT/3P (now part of the Wirtgen group)
  • Huber — Company
  • HYPAC (USA) — part of Bomag USA
  • Hyster (USA) — SD/TD/PT (part of HYPAC and Bomag USA)
  • Ingersoll Rand (USA) — SD/TD/PT (now owned by VOLVO)
  • Ingram Compaction
  • Kamani Engineering Corporation (India) (now part of the RPG Group)  — tractor-mounted  — production ended c. 1970-1980
  • Kemna, Breslau
  • KMEC
  • Lebrero (Spain) — SD/TD/PT
  • LeeBoy (USA) — SD
  • LiuGong
  • Magistral-S (Russia)
  • Marshall (England) — TD
  • Mikasa Sangyo (Japan)
  • Moore Malcolm Road Rollers (Australia) — PT (now disbanded)
  • Multiquip/Rammax
  • Mustang (England)
  • Pacific Road Roller (Australia) — SD/PT (disbanded)
  • Pannel Plant (Australia) — SD/TD (purchased by Bomag)
  • Raygo (USA) — SD/TD/PT (purchased by Caterpillar)
  • Rex (USA) — SD/TD/3P (purchased by CMI and then Terex)
  • Sakai Heavy Industries, Ltd. (Japan) — SD/TD/PT/3P
  • Sany (China) — SD/TD/PT
  • Sicom (Italy) — SD/TD
  • Simesa (Italy) — SD
  • Sinoway Industrial (Shanghai) Co.,Ltd
  • [World Equipment](China) — SD/TD/PT
  • STA / Stavostroj (Czech Republic) — SD/TD/PT (now owned by Ammann; many companies use the STA PT roller design)
  • STAMPEDE (South Africa)
  • Stone Equipment (USA) — SD
  • Strothert & Pitt (England) — TD
  • SuperPac (Canada) — SD (was Champion Superpac)
  • Tampo (USA) — SD/TD
  • VIPAC (South-Africa) - Manufactured by HA Plant Maintenance (High Quality Pedestrian Rollers)-TD
  • Vibromax (Germany) — SD/TD/PT (purchased by JCB, now branded JCB)
  • Volvo CE (Sweden) — SD/TD/PT (purchased Ingersoll Rand, now branded Volvo)
  • Wacker Neuson
  • Wallis & Stevens (England) — 3P
  • Waterous Engine Co.
  • NTC STAVEBNI TECHNIKA (Czech Republic) — manufacturer of walk-behind and light tandem rollers

KEY:

See also

Wikimedia Commons has media related to Road rollers.

External links

This article is issued from Wikipedia - version of the Friday, April 08, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.