Root mean square

In statistics, the root mean square (abbreviated RMS or rms), also known as the quadratic mean, is defined as the square root of the arithmetic mean of the squares of a set of numbers.[1] RMS can also be defined for a continuously varying function in terms of an integral of the squares of the instantaneous values during a cycle.

For a cyclically alternating electric current, RMS is equal to the value of the direct current that would produce the same power dissipation in a resistive load.[1] In econometrics the root mean square error of an estimator is a measure of the imperfection of the fit of the estimator to the data.

The root mean square is a particular case of the generalized mean, with exponent 2.

Definition

The RMS value of a set of values (or a continuous-time waveform) is the square root of the arithmetic mean of the squares of the values, or the square of the function that defines the continuous waveform.

In the case of a set of n values \{x_1,x_2,\dots,x_n\}, the RMS


x_{\mathrm{rms}} =
\sqrt{ \frac{1}{n} \left( x_1^2 + x_2^2 + \cdots + x_n^2 \right) }.

The corresponding formula for a continuous function (or waveform) f(t) defined over the interval T_1 \le t \le T_2 is


f_{\mathrm{rms}} = \sqrt {{1 \over {T_2-T_1}} {\int_{T_1}^{T_2} {[f(t)]}^2\, dt}},

and the RMS for a function over all time is


f_\mathrm{rms} = \lim_{T\rightarrow \infty} \sqrt {{1 \over {T}} {\int_{0}^{T} {[f(t)]}^2\, dt}}.

The RMS over all time of a periodic function is equal to the RMS of one period of the function. The RMS value of a continuous function or signal can be approximated by taking the RMS of a sequence of equally spaced samples. Additionally, the RMS value of various waveforms can also be determined without calculus, as shown by Cartwright.[2]

In the case of the RMS statistic of a random process, the expected value is used instead of the mean.

RMS of common waveforms

Further information: RMS amplitude

If the waveform is a pure sine wave, the relationships between amplitudes (peak-to-peak, peak) and RMS are fixed and known, as they are for any continuous periodic wave. However, this is not true for an arbitrary waveform which may or may not be periodic or continuous. For a zero-mean sine wave, the relationship between RMS and peak-to-peak amplitude is:


\mbox{Peak-to-peak} = 2 \sqrt{2} \times \mbox{RMS} \approx 2.8 \times \mbox{RMS} \,
.

For other waveforms the relationships are not the same as they are for sine waves.

Sine, square, triangle, and sawtooth waveforms
A rectangular pulse wave of duty cycle D, the ratio between the pulse duration (\tau) and the period (T); illustrated here with a = 1
Graph of a sine wave's voltage vs. time (in degrees), showing RMS, peak(PK), and peak-to-peak(PP) voltages
WaveformEquationRMS
DC, constanty=a\,a\,
Sine wavey=a\sin(2\pi ft)\,\frac{a}{\sqrt{2}}
Square wavey=\begin{cases}a & \{ft\} < 0.5 \\ -a & \{ft\} > 0.5 \end{cases}a\,
DC-shifted square wavey=\begin{cases}a+DC & \{ft\} < 0.5 \\-a+DC & \{ft\} > 0.5 \end{cases}{\sqrt{DC^2 + a^2}}\,
Modified sine wavey=\begin{cases}0 & \{ft\} < 0.25 \\ a & 0.25 < \{ft\} < 0.5 \\ 0 & 0.5 < \{ft\} < 0.75 \\ -a & \{ft\} > 0.75 \end{cases}\frac{a}{\sqrt{2}}
Triangle wave y=|2a\{ft\}-a\,| a \over \sqrt 3
Sawtooth wave y=2a\{ft\}-a\, a \over \sqrt 3
Pulse train y=\begin{cases}a & \{ft\} < D \\ 0 & \{ft\} > D \end{cases}a \sqrt{D}
Phase-to-phase voltage y=a\sin(t)-a\sin(t-\frac{2\pi}{3})\,a \sqrt{\frac{3}{2}}
Notes:
t is time
f is frequency
a is amplitude (peak value)
D is the duty cycle or the percent(%) spent high of the period (1/f)
{r} is the fractional part of r

RMS of waveform combinations

Waveforms made by summing known simple waveforms have an RMS that is the root of the sum of squares of the component RMS values, if the component waveforms are orthogonal (that is, if the average of the product of one simple waveform with another is zero for all pairs other than a waveform times itself).[3]

RMS_{Total} =
\sqrt {{{RMS_1}^2 + {RMS_2}^2 + \cdots + {RMS_n}^2} }

A special case of this, particularly helpful in electrical engineering, is given #In electrical engineering below. Another special case, useful in statistics, is given in #Relationship to other statistics.

Uses

The RMS value of a function is often used in physics and electrical engineering.

In electrical engineering

Root-mean-square voltage

Further information: Root mean square AC voltage

In electrical engineering, a special case of #RMS of waveform combinations (see also #Relationship to other statistics) is:

RMS_{Total} =
\sqrt {{{RMS_{DC}}^2 + {RMS_{AC}}^2} }

where RMS_{DC} refers to the direct current component of the signal and RMS_{AC} is the alternating current component of the signal.

Average electrical power

Further information: AC power

Electrical engineers often need to know the power, P, dissipated by an electrical resistance, R. It is easy to do the calculation when there is a constant current, I, through the resistance. For a load of R ohms, power is defined simply as:

P = I^2 R.

However, if the current is a time-varying function, I(t), this formula must be extended to reflect the fact that the current (and thus the instantaneous power) is varying over time. If the function is periodic (such as household AC power), it is still meaningful to discuss the average power dissipated over time, which is calculated by taking the average power dissipation:

P_\mathrm{avg}\,\! = \langle I(t)^2R \rangle \,\! (where \langle \ldots \rangle denotes the mean of a function)
= R\langle I(t)^2 \rangle\,\! (as R does not vary over time, it can be factored out)
= I_\mathrm{RMS}^2R\,\! (by definition of RMS)

So, the RMS value, IRMS, of the function I(t) is the constant current that yields the same power dissipation as the time-averaged power dissipation of the current I(t).

Average power can also be found using the same method that in the case of a time-varying voltage, V(t), with RMS value VRMS,

P_\mathrm{avg} = {V_\mathrm{RMS}^2\over R}.

This equation can be used for any periodic waveform, such as a sinusoidal or sawtooth waveform, allowing us to calculate the mean power delivered into a specified load.

By taking the square root of both these equations and multiplying them together, the power is found to be:

P_\mathrm{avg} = V_\mathrm{RMS}I_\mathrm{RMS}.

Both derivations depend on voltage and current being proportional (i.e., the load, R, is purely resistive). Reactive loads (i.e., loads capable of not just dissipating energy but also storing it) are discussed under the topic of AC power.

In the common case of alternating current when I(t) is a sinusoidal current, as is approximately true for mains power, the RMS value is easy to calculate from the continuous case equation above. If Ip is defined to be the peak current, then:

I_{\mathrm{RMS}} = \sqrt {{1 \over {T_2-T_1}} {\int_{T_1}^{T_2} {(I_\mathrm{p}\sin(\omega t)}\, })^2 dt}.\,\!

where t is time and ω is the angular frequency (ω = 2π/T, where T is the period of the wave).

Since Ip is a positive constant:

I_{\mathrm{RMS}} = I_\mathrm{p}\sqrt {{1 \over {T_2-T_1}} {\int_{T_1}^{T_2} {\sin^2(\omega t)}\, dt}}.

Using a trigonometric identity to eliminate squaring of trig function:

I_{\mathrm{RMS}} = I_\mathrm{p}\sqrt {{1 \over {T_2-T_1}} {\int_{T_1}^{T_2} {{1 - \cos(2\omega t) \over 2}}\, dt}}
I_{\mathrm{RMS}} = I_\mathrm{p}\sqrt {{1 \over {T_2-T_1}} \left [ {{t \over 2} -{ \sin(2\omega t) \over 4\omega}} \right ]_{T_1}^{T_2} }

but since the interval is a whole number of complete cycles (per definition of RMS), the sin terms will cancel out, leaving:

I_{\mathrm{RMS}} = I_\mathrm{p}\sqrt {{1 \over {T_2-T_1}} \left [ {{t \over 2}} \right ]_{T_1}^{T_2} } = I_\mathrm{p}\sqrt {{1 \over {T_2-T_1}} {{{T_2-T_1} \over 2}} } = {I_\mathrm{p} \over {\sqrt 2}}.

A similar analysis leads to the analogous equation for sinusoidal voltage:

V_{\mathrm{RMS}} = {V_\mathrm{p} \over {\sqrt 2}}.

Where IP represents the peak current and VP represents the peak voltage.

Because of their usefulness in carrying out power calculations, listed voltages for power outlets, e.g. 120 V (USA) or 230 V (Europe), are almost always quoted in RMS values, and not peak values. Peak values can be calculated from RMS values from the above formula, which implies Vp = VRMS × √2, assuming the source is a pure sine wave. Thus the peak value of the mains voltage in the USA is about 120 × √2, or about 170 volts. The peak-to-peak voltage, being twice this, is about 340 volts. A similar calculation indicates that the peak-to-peak mains voltage in Europe is about 650 volts.

RMS quantities such as electric current are usually calculated over one cycle. However for some purposes the RMS current over a longer period is required when calculating transmission power losses. The same principle applies, and (for example) a current of 10 amps used for 12 hours each day represents an RMS current of 5 amps in the long term.

The term "RMS power" is sometimes erroneously used in the audio industry as a synonym for "mean power" or "average power" (it is proportional to the square of the RMS voltage or RMS current in a resistive load). For a discussion of audio power measurements and their shortcomings, see Audio power.

Root-mean-square speed

In the physics of gas molecules, the root-mean-square speed is defined as the square root of the average squared-speed. The RMS speed of an ideal gas is calculated using the following equation:

{v_\mathrm{RMS}} = {\sqrt{3RT \over {M}}}

where R represents the ideal gas constant, 8.314 J/(mol·K), T is the temperature of the gas in kelvins, and M is the molar mass of the gas in kilograms. The generally accepted terminology for speed as compared to velocity is that the former is the scalar magnitude of the latter. Therefore, although the average speed is between zero and the RMS speed, the average velocity for a stationary gas is zero.

Root-mean-square error

When two data sets—one set from theoretical prediction and the other from actual measurement of some physical variable, for instance—are compared, the RMS of the pairwise differences of the two data sets can serve as a measure how far on average the error is from 0.

The mean of the pairwise differences does not measure the variability of the difference, and the variability as indicated by the standard deviation is around the mean instead of 0. Therefore, the RMS of the differences is a meaningful measure of the error.

RMS in frequency domain

The RMS can be computed in the frequency domain, using Parseval's theorem. For a sampled signal x[n]=x(t=nT), where T is the sampling period,

\sum_{n=1}^{N}{{{x}^{2}}[n]} = \frac{1}{N}\sum_{m=1}^{N} \left| X[m] \right|^{2},

where X[m]=\mathrm{FFT}\{x[n]\} and N is number of samples and FFT coefficients.

In this case, the RMS computed in the time domain is the same as in the frequency domain:

\mathrm{RMS}\{x[n]\}
 =\sqrt{\frac{1}{N}\sum_{n}{{{x}^{2}}[n]}}
 = \sqrt{\frac{1}{N^2}\sum_{m}{{{\left| X[m] \right|}^{2}}}}
 = \sqrt{\sum_{m}{{{ \left|\frac{X[m]}{N}\right| ^ 2 }}}}.

Relationship to other statistics

If \bar{x} is the arithmetic mean and \sigma_{x} is the standard deviation of a population or a waveform then:[4]

x_{\mathrm{rms}}^2 = \bar{x}^2 + \sigma_{x}^2 = \overline{x^{2}}.

From this it is clear that the RMS value is always greater than or equal to the average, in that the RMS includes the "error" / square deviation as well.

Physical scientists often use the term "root mean square" as a synonym for standard deviation when it can be assumed the input signal has zero mean, i.e., referring to the square root of the mean squared deviation of a signal from a given baseline or fit.[5] [6] This is useful for electrical engineers in calculating the "AC only" RMS of a signal. Standard deviation being the root mean square of a signal's variation about the mean, rather than about 0, the DC component is removed (i.e. RMS(signal) = Stdev(signal) if the mean signal is 0). A special case of this, particularly helpful in electrical engineering, is given above.

See also

References

  1. 1 2 A Dictionary of Physics (6 ed.). Oxford University Press. 2009. ISBN 9780199233991.
  2. Cartwright, Kenneth V (Fall 2007). "Determining the Effective or RMS Voltage of Various Waveforms without Calculus" (PDF). Technology Interface 8 (1): 20 pages.
  3. Nastase, Adrian S. "How to Derive the RMS Value of Pulse and Square Waveforms". MasteringElectronicsDesign.com. Retrieved 21 January 2015.
  4. Chris C. Bissell and David A. Chapman (1992). Digital signal transmission (2nd ed.). Cambridge University Press. p. 64. ISBN 978-0-521-42557-5.
  5. "Root-Mean-Square".
  6. "ROOT, TH1:GetRMS".

External links

This article is issued from Wikipedia - version of the Thursday, April 21, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.