Drum hardware
| The drum kit |
|
|
1 Bass drum | 2 Floor tom | 3 Snare drum |
| Not shown |
|
Sizzle cymbal | Swish cymbal | Crash/ride cymbal |
| See also |
Drum hardware refers to the parts of a drum or drum kit that are used to tension, position, and otherwise support the instruments themselves.
Occasionally, the hardware is used percussively as well, the most common example being a rim shot. John Morrison is noted for his drum solos played entirely on a hi-hat stand (and occasionally also on other parts of the kit hardware, adjacent furniture, and audience).
Drum parts
Rim
A drum "hoop" or "rim" may be made of metal, wood, or other materials and is used to hold a drumhead against a drum shell, either with bolts through metal "claws" attached directly to a hoop, or bolts through holes in a flanged rim. The bolts, called tension rods, are screwed into threaded "lugs" attached to the drum shell, in order to tighten and tune the drumhead.[1] A drum key is a type of wrench often used to screw the tension rods into the lugs.
Spurs, casings, lugs, tuning screws
(tension rod) tension rod washer. this tightens the drum skin and applies pressure around the rim to create the drum's sound
Snare tensioner
Snare drums will often have a "strainer" on one side and a "butt plate" on the other to hold the snare wires to the drumhead. Snare tension is controlled with a screw on the strainer. A strainer may also have a "throwoff" lever to move snares away from the drumhead, in order to prevent buzzing caused by other bass instruments while the snare is not in use, or to produce a tom-tom sound if desired.[2]
Badge
While not required for operation, most drum manufacturers label their products by way of a drum "badge". The badge is a label attached to the drum shell with a grommet, which is embossed with the manufacturer's name or logo, and often a serial number as well. The grommet doubles as a "vent" hole for two-sided drums.[3]
Bass Drum Legs
The bass drum(s) in a drum kit usually sit on the floor, and as such require support to prevent rolling. Two adjustable legs are attached by clamps to either side of the shell.[4]
Mounts
Drum mounts are fittings, normally attached to the drum shell, that enable a drum to be attached to a supporting bracket, stand or rack. Traditionally, smaller tom-tom drums are supported by mounts and known as hanging toms, while snare drums rest on a stand not attached to the drum, and floor toms and bass drums rest on their own legs.[5]
Hanging tom mounts are of two main patterns:
- The Pearl 7/8" (22mm) mount accepts a 22mm steel tube perpendicular to the drum shell. The excess length of the tube intrudes through the drum shell, and a large hole is required for this. Developed by Pearl, this mount has been adopted by many other manufacturers, and the 22mm tube has become a standard interface for many other mounts and stands, such as cymbal booms.
- The parallel mount accepts a solid bar parallel to the drum shell. There are many bar sizes and profiles, mostly either round and knurled or hexagonal. There is a some compatibility, but it is not universal. Some manufacturers such as Tama Drums and Gibraltar Hardware even produce a single fitting that can be used either singly as a hanging tom mount, or in sets of three to attach the floor tom legs.
Either of these patterns can also be used with a rim mount. Most fittings have provision for memory to reduce setup time.
|
There are many other patterns, including:
- Similar mounts to the 7/8" but with smaller tube. Mostly used on toy and entry level kits.
- Spade mounts on older kits and, traditionally, on timbales.
- Mounts that accept a solid bar similar to the parallel mount, but perpendicular to the drum shell or at an angle close to this. Common on older kits, and on some high-level handmade kits from smaller makers.
Stands and holders
Metal stands and holders are used to support percussion instruments or microphones. Floor stands are often tripods and telescoping.
Tom-tom and cymbal stands may have a "boom arm" attached to extend holder reach, and a "tilter" to move instruments into a desired position. Smaller "clamp holders" may also be used to attach more instruments to existing stands. Drum "racks" are stands surrounding a drum kit onto which percussion instrument holders may be clamped. "Memory locks" are clamps used to make drum and telescoping positions permanent.
Snare drum stand
Snare drum stands have three arms as a "basket" to cradle the lower rim of the drum. There are several patterns.
The older, traditional pattern has two arms that pivot, and one that slides to accommodate varying sizes of drum. This is satisfactory for a tilted drum; The drum is tilted away from the sliding arm and rests on the two pivoting arms. If it is horizontal, or tilted the wrong way by inexpert players, then the drum is insecure.
|
The newer patterns use a symmetrical basket with a central screw adjustment, allowing the basket to be tightened onto the lower rim and the drum to be firmly held at any angle. They differ mainly in sturdiness and in the precise mechanism used for the screw adjustment.
Snare drum stands have long been used by some drummers to support tom-tom drums. In this application they offer much the same advantages as the more recently available rim mounts.
Rack toms
Hanging toms are traditionally supported by tom-tom arms or brackets mounted on the bass drum, with one or two toms supported by each bass drum.
Extra toms may be supported by stands or racks.
Floor tom
Floor toms are traditionally supported by three feet resting on the floor, as the name suggests. More recently, some drummers have used rim mounts.
Cymbal stands
Cymbal stands have a threaded bolt or "cymbal post" to hold a cymbal down with a nut. Accessory booms and piggyback adaptors allow additional cymbals to be added to an existing stand (not to be confused with stacking).
Hi-hat stand
A hi-hat stand is a standard part of the hardware of a drum kit.[5] In an extended kit, additional pairs of hi-hat cymbals may be operated remotely by a cable hat, or held closed by an X-hat adaptor.
Drum throne
The drum "throne" is a three or four-legged padded seat or stool the drummer sits on while playing. Thrones may be shaped like round cushions or in a saddle design. Throne heights may be adjusted to accommodate the drummer.[5]
Memory
Many drum stands and brackets have provision for memory. This consists of a mechanical device, such as a collar, that allows quick reassembly in a preset position after the kit has been disassembled.
|
Drum rack
.JPG)
Some or all of the stands can be replaced by a drum rack. Racks are particularly used for larger kits, but can greatly reduce the weight and setup time of even moderately sized kits.
Cymbals and hanging toms are most often mounted on the rack, but bass drums, floor toms and even snare drums can be rack mounted, particularly if rim mounts are used.
Drum pedals
Pedals used with drums include:
Drum hardware manufacturers
- Axis Percussion
- Gibraltar Hardware
- Pearl Drums
- Sonor
- Tama
- Drum Workshop
- Yamaha Drums
- Pacific Drums and Percussion
- Sound Percussion
- Ludwig
- CB Percussion
- Alesis
- Drum Giant
- Crush Drums and Percussion
- Craviotto Drum Company
- SJC Custom Drums
- Pintech
See also
References
- ↑ International House of Blues Foundation. "Making a Drum" 2003
- ↑ Okamoto, Gene. " HOW TO REPLACE AND ADJUST SNARES" 1995-2003
- ↑ "Drum Sample Library". Retrieved 10 April 2014.
- ↑ Marshall, Paul. Radcliff, Mike. "Glossary of Terms (Drum kit/Drumset)" 1999
- 1 2 3 4 "Pearl Drums Hardware" 2004