Thrust vectoring

Thrust vectoring nozzle on a Sukhoi Su-35S
The F-18 HARV, X-31, and F-16 MATV in flight

Thrust vectoring, also thrust vector control or TVC, is the ability of an aircraft, rocket, or other vehicle to manipulate the direction of the thrust from its engine(s) or motor(s) in order to control the attitude or angular velocity of the vehicle.

In rocketry and ballistic missiles that fly outside the atmosphere, aerodynamic control surfaces are ineffective, so thrust vectoring is the primary means of attitude control.

For aircraft, the method was originally envisaged to provide upward vertical thrust as a means to give aircraft vertical (VTOL) or short (STOL) takeoff and landing ability. Subsequently, it was realized that using vectored thrust in combat situations enabled aircraft to perform various maneuvers not available to conventional-engined planes. To perform turns, aircraft that use no thrust vectoring must rely on aerodynamic control surfaces only, such as ailerons or elevator; craft with vectoring must still use control surfaces, but to a lesser extent.

In missile literature originating from Russian sources,[1] thrust vectoring is often referred as "gas-dynamic steering" or "gas-dynamic control".

Thrust vectoring methods

Rockets and ballistic missiles

Moments generated by different thrust gimbal angles
Animation of the motion of a rocket as the thrust is vectored by actuating the nozzle
Graphite exhaust vanes on a V-2 rocket motor's nozzle

Thrust vector control (TVC) is used when the propulsion system is creating thrust. At other stages of flight, separate mechanisms are required for attitude and flight path control.

Thrust vectoring can be achieved by five basic means:[2][3]

Nominally, the line of action of the thrust vector of a rocket nozzle passes through the vehicle's center of mass, generating zero net moment about the mass center. It is possible to generate pitch and yaw moments by deflecting the main rocket thrust vector so that it does not pass through the mass center. Because the line of action is generally oriented nearly parallel to the roll axis, roll control usually requires the use of two or more separately hinged nozzles or a separate system altogether, such as fins, or vanes in the exhaust plume of the rocket engine, deflecting the main thrust.

Thrust vectoring for many liquid rockets is achieved by gimbaling the rocket engine. This often involves moving the entire combustion chamber and outer engine bell as on the Titan II's twin first-stage motors, or even the entire engine assembly including the related fuel and oxidizer pumps. The Saturn V and the Space Shuttle used gimballed engines.[2]

Another method of thrust vectoring used on early solid propellant ballistic missiles was liquid injection, in which the rocket nozzle is fixed, but a fluid is introduced into the exhaust flow from injectors mounted around the aft end of the missile. If the liquid is injected on only one side of the missile, it modifies that side of the exhaust plume, resulting in different thrust on that side and an asymmetric net force on the missile. This was the control system used on the Minuteman II and the early SLBMs of the United States Navy.

A later method developed for solid propellant ballistic missiles achieves thrust vectoring by deflecting the rocket nozzle using electric servomechanisms or hydraulic cylinders. The nozzle is attached to the missile via a ball joint with a hole in the center, or a flexible seal made of a thermally resistant material, the latter generally requiring more torque and a higher power actuation system. The Trident C4 and D5 systems are controlled via hydraulically actuated nozzle.

The Apollo Lunar Module had a fixed engine in the ascent stage. Attitude control was achieved by using 16 auxiliary reaction control system engines in 4 clusters mounted on the ascent stage. The descent stage engine gimbaled, but this was computer-controlled to keep the thrust vector aligned with the center of mass and attitude control was by the ascent stage RCS. The V-2 used exhaust vanes and aerodynamic vanes, as did the Redstone, derived from the V-2.

Tactical missiles and small projectiles

Some smaller sized atmospheric tactical missiles, such as the AIM-9X Sidewinder, eschew flight control surfaces and instead use mechanical vanes to deflect motor exhaust to one side.

Thrust vectoring is a way to reduce a missile's minimum range, before which it cannot reach a speed high enough for its small aerodynamic surfaces to produce effective maneuver. For example, anti-tank missiles such as the ERYX and the PARS 3 LR use thrust vectoring for this reason.[4]

Some other projectiles that use thrust-vectoring:

Aircraft

Most currently operational vectored thrust aircraft use turbofans with rotating nozzles or vanes to deflect the exhaust stream. This method can successfully deflect thrust through as much as 90 degrees, relative to the aircraft centerline. However, the engine must be sized for vertical lift, rather than normal flight, which results in a weight penalty. Afterburning (or Plenum Chamber Burning, PCB, in the bypass stream) is difficult to incorporate and is impractical for take-off and landing thrust vectoring, because the very hot exhaust can damage runway surfaces. Without afterburning it is hard to reach supersonic flight speeds. A PCB engine, the Bristol Siddeley BS100, was cancelled in 1965.

Tiltrotor aircraft vector thrust via rotating turboprop engine nacelles. The mechanical complexities of this design are quite troublesome, including twisting flexible internal components and driveshaft power transfer between engines. Most current tiltrotor designs feature 2 rotors in a side-by-side configuration. If such a craft is flown in a way where it enters a vortex ring state, one of the rotors will always enter slightly before the other, causing the aircraft to perform a drastic and unplanned roll.

The pre-World War 1, British Army airship Delta, fitted with swiveling propellers

Thrust vectoring is also used as a control mechanism for airships. An early application was the British Army airship Delta, which first flew in 1912.[7] It was later used on HMA (His Majesty's Airship) No. 9r, a British rigid airship that first flew in 1916[8] and the twin 1930s-era U.S. Navy rigid airships USS Akron and USS Macon that were used as airborne aircraft carriers, and a similar form of thrust vectoring is also particularly valuable today for the control of modern non-rigid airships. In this use, most of the load is usually supported by buoyancy and vectored thrust is used to control the motion of the aircraft. But, designs have recently been proposed, especially for Project WALRUS, where a significant portion of the weight of the craft is supported by vectored thrust. The first airship that used a control system based on pressurized air was Enrico Forlanini's Omnia Dir in 1930s.

A design for a jet incorporating thrust vectoring was submitted in 1949 to the British Air Ministry by Percy Walwyn.[9] Official interest was curtailed when it was realised that the designer was a patient in a mental hospital.

Now being researched, Fluidic Thrust Vectoring (FTV) diverts thrust via secondary fluidic injections.[10] Tests show that air forced into a jet engine exhaust stream can deflect thrust up to 15 degrees. Such nozzles are desirable for their lower mass and cost (up to 50% less), inertia (for faster, stronger control response), complexity (mechanically simpler, fewer or no moving parts or surfaces, less maintenance), and radar cross section for stealth. This will likely be used in many unmanned aerial vehicle (UAVs), and 6th generation fighter aircraft.

Vectoring nozzles

Main article: Vectoring nozzles

Thrust-Vectoring flight control (TVFC) is obtained through deflection of the aircraft jets in some or all of the pitch, yaw and roll directions. In the extreme, deflection of the jets in yaw, pitch and roll creates desired forces and moments enabling complete directional control of the aircraft flight path without the implementation of the conventional aerodynamic flight controls (CAFC). TVFC can also be used to hold stationary flight in areas of the flight envelope where the main aerodynamic surfaces are stalled.[11] TVFC includes control of STOVL aircraft during the hover and during the transition between hover and forward speeds below 50 knots where aerodynamic surfaces are ineffective.[12]

When vectored thrust control uses a single propelling jet, as with a single-engined aircraft, the ability to produce rolling moments may not be possible. An example is an afterburning supersonic nozzle where nozzle functions are throat area, exit area, pitch vectoring and yaw vectoring. These functions are controlled by 4 separate actuators.[11] A simpler variant using only 3 actuators would not have independent exit area control.[11]

When TVFC is implemented to complement CAFC, agility and safety of the aircraft are maximized. Increased safety may occur in the event of malfunctioning CAFC as a result of battle damage. [11]

To implement TVFC a variety of nozzles both mechanical and fluidic may be applied. This includes convergent and convergent-divergent nozzles that may be fixed or geometrically variable. It also includes variable mechanisms within a fixed nozzle, such as rotating cascades[13] and rotating exit vanes.[14] Within these aircraft nozzles, the geometry itself may vary from two-dimensional (2-D) to axisymmetric or elliptic. The number of nozzles on a given aircraft to achieve TVFC can vary from one on a CTOL aircraft to a minimum of four in the case of STOVL aircraft.[12]

It is necessary to clarify some definitions used in thrust-vectoring nozzle design.

Methods of Nozzle Control

Type I – Nozzles whose baseframe mechanically is rotated before the geometrical throat.

Type II – Nozzles whose baseframe is mechanically rotated at the geometrical throat.

Type III – Nozzles whose baseframe is not rotated. Rather, the addition of mechanical deflection post-exit vanes or paddles enables jet deflection.

Type IV – Jet deflection through counter-flowing or co-flowing (by shock-vector control or throat shifting)[16] auxiliary jet streams. Fluid-based jet deflection using secondary fluidic injection.[16]

additional type - Nozzles whose upstream exhaust duct consists of wedge-shaped segments which rotate relative to each other about the duct cenreline.[12][17][18]

Operational examples

Sea Harrier FA.2 ZA195 front (cold) vector thrust nozzle

A famous example of thrust vectoring is the Rolls-Royce Pegasus engine used in the Hawker Siddeley Harrier, as well as in the AV-8B Harrier II variant.

Widespread use of thrust vectoring for enhanced maneuverability in Western production-model fighter aircraft didn't occur until the deployment of the Lockheed Martin F-22 Raptor fifth-generation jet fighter in 2005, with its afterburning, thrust-vectoring Pratt & Whitney F119 turbofan.[19]

Lockheed Martin F-35 Lightning II is currently in the pre-production test and development stage. Although this aircraft uses a conventional afterburning turbofan (Pratt & Whitney F135) to facilitate supersonic operation, the F-35B variant, developed for joint usage by the US Marine Corps, Royal Air Force, Royal Navy, and Italian Navy, also incorporates a vertically mounted, low-pressure shaft-driven remote fan, which is driven through a clutch during landing from the engine. Both the exhaust from this fan and the main engine's fan are deflected by thrust vectoring nozzles, to provide the appropriate combination of lift and propulsive thrust.

The Sukhoi Su-30 MKI, produced by India under license at Hindustan Aeronautics Limited is in active service with the Indian Air Force. The TVC makes the aircraft highly maneuverable, capable of near-zero airspeed at high angles of attack without stalling, and dynamic aerobatics at low speeds. The Su-30MKI is powered by two Al-31FP afterburning turbofans. The TVC nozzles of the MKI are mounted 32 degrees outward to longitudinal engine axis (i.e. in the horizontal plane) and can be deflected ±15 degrees in the vertical plane. This produces a corkscrew effect, greatly enhancing the turning capability of the aircraft.[20]

Examples of rockets and missiles which use thrust vectoring include both large systems such as the Space Shuttle Solid Rocket Booster (SRB), S-300P (SA-10) surface-to-air missile, UGM-27 Polaris nuclear ballistic missile and RT-23 (SS-24) ballistic missile and smaller battlefield weapons such as Swingfire.

The principles of air thrust vectoring have been recently adapted to military sea applications in the form of fast water-jet steering that provide super-agility. Examples are the fast patrol boat Dvora Mk-III, the Hamina class missile boat and the US Navy's Littoral combat ships. A few computerized studies add thrust vectoring to extant passenger airliners, like the Boeing 727 and 747, to prevent catastrophic failures, while the experimental X-48C may be jet-steered in the future.[21]

List of vectored thrust aircraft

Thrust vectoring can convey two main benefits: VTOL/STOL, and higher maneuverability. Aircraft are usually optimized to maximally exploit one benefit, though will gain in the other.

For VTOL ability

The Harrier—the world's first operational fighter jet with thrust vectoring, enabling VTOL capabilities
GE Axisymmetric Vectoring Exhaust Nozzle, used on the F-16 MATV

For higher maneuverability

Vectoring in two dimensions

Vectoring in three dimensions

Other

See also

References

  1. ↑ "AA-11 ARCHER R-73". Retrieved 2014-03-27.
  2. 1 2 George P. Sutton, Oscar Biblarz, Rocket Propulsion Elements, 7th Edition.
  3. ↑ Michael D. Griffin and James R. French, Space Vehicle Design, Second Edition.
  4. 1 2 "Anti-tank guided missile developments". Retrieved 2014-03-27.
  5. ↑ "Combat Vehicle Tor 9A330". State company "UKROBORONSERVICE". Retrieved 2014-03-27.
  6. ↑ "S-400 SA-20 Triumf". Federation of American Scientists. Retrieved 2014-03-27.
  7. ↑ Mowthorpe, Ces (1998). Battlebags: British Airships of the First World War. Wrens Park. p. 11. ISBN 0-905778-13-8.
  8. ↑ Abbott, Patrick (1989). The British Airship at War. Terence Dalton. p. 84. ISBN 0-86138-073-8.
  9. ↑ diomedia.com
  10. ↑ P. J. Yagle; D. N. Miller; K. B. Ginn; J. W. Hamstra (2001). "Demonstration of Fluidic Throat Skewing for Thrust Vectoring in Structurally Fixed Nozzles". Journal of Engineering for Gas Turbines and Power 123 (3): 502–508. doi:10.1115/1.1361109.
  11. 1 2 3 4 5 6 7 8 "Thrust Vectoring Nozzle for Modern Military Aircraft" Daniel Ikaza, ITP, presented at NATO R&T Organization Symposium, Braunschweig, Germany, 8–11 May 2000
  12. 1 2 3 4 "F-35B Integrated Flight Propulsion Control Development" Walker, Wurth, Fuller, AIAA 2013-44243, AIAA Aviation, August 12–14, 2013, Los Angeles, CA 2013 International Powewred Lift Conference"
  13. ↑ "The X-Planes, Jay Miller, Aerofax Inc. for Orion Books, ISBN 0-517-56749-0, Chapter 18, The Bell X-14
  14. ↑ "Propulsion System For A Vertical And Short Takeoff And Landing Aircraft" Bevilaqua and Shumpert, U.S. Patent Number 5,209,428
  15. 1 2 "Nozzle Selection and Design Criteria" Gambell, Terrell, DeFrancesco, AIAA 2004-3923
  16. 1 2 3 "Experimental Study of an Axisymmetric Dual Throat Fluidic Thrust Vectoring Nozzle for Supersonic Aircraft application" Flamme, Deere, Mason, Berrier, Johnson, http://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/20070030933.pdf
  17. 1 2 http://www.codeonemagazine.com/article.html?item_id=137
  18. ↑ "Variable Vectoring Nozzle For Jet Propulsion Engines" Johnson, U.S. Patent 3,260,049
  19. ↑ "F-22 Raptor fact sheet." U.S. Air Force, March 2009. Retrieved: 10 July 2014.
  20. ↑ Air-Attack.com - Su-30MK AL-31FP engines two-dimensional thrust vectoring.
  21. ↑ Gal-Or, Benjamin (2011). "Future Jet Technologies". International Journal of Turbo and Jet Engines (online) 28: 1–29. ISSN 2191-0332.
  22. 1 2 Sweetman, Bill (1999). Joint Strike Fighter: Boeing X-32 vs Lockheed Martin X-35. Enthusiast Color Series. MBI. ISBN 0-7603-0628-1.

8. Wilson, Erich A., "An Introduction to Thrust-Vectored Aircraft Nozzles", ISBN 978-3-659-41265-3

External links

This article is issued from Wikipedia - version of the Wednesday, April 13, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.