Track geometry car

Track geometry car in Russia
Track geometry car in New York City, USA

A track geometry car (also known as a track recording car) is an automated track inspection vehicle on a rail transport system used to test several geometric parameters of the track without obstructing normal railroad operations. Some of the parameters generally measured include position, curvature, alignment of the track, smoothness, and the crosslevel of the two rails. The cars use a variety of sensors, measuring systems, and data management systems to create a profile of the track being inspected.

History

By at least 1967, geometry cars had emerged. One of the earliest was Car T2 used by the U.S. Department of Transportation's Project HISTEP (High-Speed Train Evaluation Program). It was built by the Budd Company especially for Project HISTEP to evaluate track conditions between Trenton and New Brunswick, NJ, where the DOT had established a section of track for testing high-speed trains, and accordingly, the T2 ran at or greater than 150 miles per hour.[1]
Many of the first regular service geometry cars were created from old passenger cars outfitted with the appropriate sensors, instruments, and recording equipment; they were then coupled behind a locomotive.[2] By at least 1977, self-propelled geometry cars had emerged. Southern Pacific's GC-1 (built by Plasser American) was among the first and utilized twelve measuring wheels in conjunction with strain gauges, computers, and spreadsheets to give managers a clear picture of the condition of the railroad.[3] Even in 1981, the Encyclopedia of North American Railroads considered this the most advanced track geometry car in North America.[4]

Advantages

Track inspection was originally done by track inspectors walking the railroad and visually inspecting every section of track. This was hazardous as it had to be done while trains were running. It was also manpower intensive, and inspectors were limited in the amount of track they could inspect on a given day. Manual instruments had to be used to measure various parameters of the track.[2]
The primary benefits of track geometry cars are the time and labor saved when compared to doing manual inspections of track. Track geometry cars may travel up to 217 miles per hour (335 kilometers per hour), inspecting track the whole time. More commonly, on freight railroads, geometry cars travel at track speed (up to seventy miles per hour) in order to minimize service disruptions. Current track geometry cars may cover large portions of the system in a single day. Many times, maintenance gangs will follow the geometry car and fix defects as the geometry car moves along the track.[2]
Because track geometry cars are full-sized rail cars (with the exception of some lighter hi-rail geometry cars), track geometry cars also provide a better picture of the geometry of the track under loading (when compared to the manual methods which did not take this into account). Finally, track geometry data is generally stored and can be used to track trends in the degradation of track. This data can be used to pinpoint and predict trouble spots in the track and plan maintenance programs accordingly.[5]

Parameters measured

The tolerances of each parameter varies by the Track class of the track being measured. In the United States, geometry cars generally classify each defect as either "Class II" or "Class I" (though the exact name may vary by the railroad). A class II defect is known as a maintenance level defect, meaning that the track doesn't meet a particular railroad's own standards. Each railroad has their own standard for a maintenance level defect. A class I defect is a defect in violation of the Federal Railroad Administration's (FRA) track safety standards. Railroads must fix these defects within a certain period of time after their discovery or else they risk being fined.

Track geometry cars used by the New York City Subway also measure:

Non-contact measurement and inspection methods

Contact measurement and inspection methods

Regulatory compliance in the United States

In the United States, the Federal Railroad Administration (FRA) maintains a fleet of three geometry cars as part of its Automated Track Inspection Program (ATIP). The FRA runs its fleet of geometry cars around the country to check railroads for compliance with Federal Track Safety Standards(FTSS). According to the FRA, each geometry car travels approximately 30,000 miles and finds approximately 10,000 defects every year, which are then fixed by the railroads.[10]

Future

In the United States, railroads are looking into new ways to measure geometry that cause even less interference to train operations. The Transportation Technology Center, Inc. (TTCI) in Pueblo, CO has been conducting tests using a portable ride quality monitoring system attached to a standard freight car. TTCI has also been promoting a move to "Performance Based Track Geometry" or PBTG. Most current track geometry systems only look at the condition of the track itself, while a PBTG system also looks at vehicle dynamics caused by track conditions.[11]

Examples

See also

References

  1. 1 2 3 Lindgren, P.W. "Project HISTEP." Proceedings of the 1968 Annual Convention, American Railway Engineering Association (AREA), 1968. Print (digitized).
  2. 1 2 3 Solomon, Brian. Railway Maintenance: The Men and Machines That Keep the Railroads Running. St. Paul, MN: MBI Publishing Company, 2001. Print.
  3. ↑ SP Track Geometry Car GC 1. Percy, Richard A. (c) 1997-2008. Web. 22 October 2009.
  4. ↑ Hubbard, Freeman H. Encyclopedia of North American Railroading. McGraw-Hill, Inc., 1981. Print
  5. ↑ William Middleton, George Smerk, and Roberta Diehl. "Track Inspection." Encyclopedia of North American Railroads. Indiana University Press, Bloomington, IN, 2007. Print.
  6. ↑ Track Safety Standards Compliance Manual. Federal Railroad Administration, 2009. Print, Web. Track Safety Standards Compliance Manual
  7. ↑ Plasser American - Machines - Recording. Plasser American Corporation, (c) 2007. Web. 19 October 2009. Plasser American - Machines - Recording
  8. ↑ Uzarski, Dr. Don. CEE 409 - Railroad Track Engineering, Class Notes. University of Illinois at Urbana-Champaign, 2009. Print.
  9. ↑ New York City Transit's Wonder Train Car!
  10. ↑ U.S. Federal Railroad Administration - Automated Track Inspection Program. Federal Railroad Administration, 2009. Web. 1 November 2009.
  11. ↑ Performance Based Track Geometry. Transportation Technology Center, Inc., 2009. Web. 19 October 2009. TTCI Performance Based Track Geometry

External links


This article is issued from Wikipedia - version of the Tuesday, June 24, 2014. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.