Turbomeca Astazou

Astazou
Turbomeca Astazou
Type Turboshaft/Turboprop
National origin France
Manufacturer Turbomeca
First run 1957
Major applications Aérospatiale Gazelle
Handley Page Jetstream



The Turbomeca Astazou is a highly successful series of turboprop and turboshaft engines, first run in 1957. The original version weighed 110 kg (243 lb) and developed 240 kW (320 shp) at 40,000 rpm. It was admitted for aviation service on May 29, 1961 after a 150-hour test run. The main developing engineer was G. Sporer. It was named after two summits of the Pyrenees.

A simplified version was built by Agusta as the Turbomeca-Agusta TA.230.

Design and development

The Astazou IIA version was derived from the original Astazou powerplant for use in helicopters. By 1993, 2,200 had been built. As of 2007, it was still in production. However, many aircraft initially equipped with it, especially the heavier ones, have since been upgraded with more powerful engines.

The basic design of the single shaft Astazou has a two-stage compressor, with the first stage an axial and the second stage a radial design. It has an annular combustion chamber, after which the hot exhaust enters a three-stage axial turbine. Maximum rpm was later raised to 43,500.

Production turbines have a reduction gear in front of the air inlet, reducing propeller speed to 1,800, 2,080, 2,200, 0r 2,400 rpm, or 6,000 rpm in the helicopter version. The engine controls itself automatically, so the pilot only needs to set the desired rpms.

As of the Astazou X, the engine received a second axial compressor stage. This was the engine for the Potez 840. The Astazou XIV and XVI were also marketed by Rolls-Royce Turboméca International Ltd under the names AZ14 and AZ16, respectively.

Power was steadily increased over the years, with the Eurocopter Dauphin's dual Astazou XVIII developing 783 kW each. The Astazou XX received a third axial stage, raising compression even further to achieve aprojected output of 1075 kW in the turboprop application. The XXB derivative, used in the single engine SA 361H Dauphin, has 1,043 kW (1,399 shp).

Astazou XVI

The circular air inlet behind the reduction gear has a de-icing device using hot air. The compressor's two axial stages use blisks. The shaft runs on ball bearings. Air flow through the annular combustion chamber is S-wise, with fuel being added in radial direction by a rotating atomizer disc. The blades of the three-stage turbine's wheels, also blisks, are air-cooled from the inside. The jet nozzle is fixed with an interior cone. Auxiliary drives are mounted on a mounting plate behind the inlet, which also has the connections for starter motor/generator, oil and fuel pumps, engine speed control and tachometer. There are also optional drives for an AC generator and a hydraulic pump. The whole engine is mounted at three points, two trunnions on the right and left front of the turbine casing and one on its underside to the rear. Speed control is effected automatically by governing the injection volume, with a thermal regulator allowing for short-term overloads.

Variants

Astazou I
Astazou II
Single-stage axial plus single-stage centrifugal compressor, annular combustor, three-stage turbine
Astazou IIA
Astazou III
Astazou IIIA
Astazou IIIC
Astazou IIIC2
Astazou IIIN
Astazou IIIN2
Astazou X
The X and subsequent engines had a second axial compressor stage added.
Astazou XII
Astazou XIV
Two-stage axial plus single-stage centrifugal compressor, annular combustor, three-stage turbine. Integral front mounted

gearbox.

Astazou XIVB
Astazou XIVD
Astazou XIVC
Astazou XIVH
Astazou XIVM
Astazou XVI
Astazou XVIII
Astazou XVIIIA
Astazou XX
A third axial compressor stage added for increased pressure ratio.
Astazou XXB
Turbomeca-Agusta TA.230
A simplified version built by Agusta.
Rolls-Royce Turboméca AZ14
The Astazou XIV marketed by Rolls-Royce Turboméca International Ltd as the AZ14
Rolls-Royce Turboméca AZ16
The Astazou XVI marketed by Rolls-Royce Turboméca International Ltd as the AZ16

Applications

Fixed-wing aircraft

Helicopters

Specifications

Parameter II[2] IIA IIIC2/N2 X XIVB/F XIVH XIVM
Max output 390 kW (523 hp) 390 kW (523 hp) 480 kW (644 hp) 465 kW (624 hp) 440 kW (590 hp) 440 kW (590 hp) 440 kW (590 hp)
Length 1,810 mm (71.3 in) 1,427.5 mm (56.2 in) 1,433.5 mm (56.4 in) 1,912 mm (75.3 in) 1,434 mm (56.5 in) 1,470 mm (57.9 in) 1,474 mm (58.0 in)
Diameter 460 mm (18.1 in) 460 mm (18.1 in) 460 mm (18.1 in) 460 mm (18.1 in) 460 mm (18.1 in) 460 mm (18.1 in) 460 mm (18.1 in)
Width 516 mm (20.3 in) 483 mm (19.0 in) 520 mm (20.5 in) 500 mm (19.7 in) 460 mm (18.1 in)
Height 560 mm (22.0 in) 508 mm (20.0 in) 623.5 mm (24.5 in) 565 mm (22.2 in) 570 mm (22.4 in)
Weight 123 kg (271.2 lb) 142 kg (313.1 lb) 150.3 kg (331.4 lb) 128 kg (282.2 lb) 160 kg (352.7 lb) 160 kg (352.7 lb) 160 kg (352.7 lb)
Air mass flow 2.5 kg (5.5 lb)/sec
Pressure ratio 6:1 7.5:1 8:1 8:1 8:1

See also

Related development


Related lists

Notes

  1. http://www.army.mod.uk/equipment/23289.aspx
  2. Taylor, John W.R. FRHistS. ARAeS (1962). Jane's All the World's Aircraft 1962-63. London: Sampson, Low, Marston & Co Ltd.

References

  • Taylor, John W.R. FRHistS. ARAeS (1962). Jane's All the World's Aircraft 1962-63. London: Sampson, Low, Marston & Co Ltd. 

Further reading

Wikimedia Commons has media related to Turbomeca Astazou.
This article is issued from Wikipedia - version of the Sunday, August 09, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.