Buoyancy compensator (diving)

"Stab jacket" redirects here. For a type of body armor, see stab vest.
Buoyancy compensator

Jacket type BC on diving cylinder
Acronym BC or BCD
Other names Buoyancy control device
Uses To adjust and control the overall buoyancy of the diver
Related items Backplate and wing

A buoyancy compensator also called a buoyancy control device, BC, BCD, stabilizer, stabilisor, stab jacket, wing or ABLJ depending on design, is a piece of diving equipment containing a bladder which is worn by divers to establish neutral buoyancy underwater and positive buoyancy on the surface, when needed. The buoyancy is controlled by adjusting the volume of air in the bladder. The bladder is filled with gas from the diver's air tank or from the diver's mouth.

Features

Backplate or wing style B.C.and scuba set
  1. Regulator first stage
  2. Cylinder valve
  3. Shoulder straps
  4. Buoyancy compensator bladder
  5. Relief and bottom manual dump valve
  6. Regulator second stages (with “octopus”)
  7. Console (pressure gauge, depth gauge & compass)
  8. Dry-suit inflator hose
  9. Backplate
  10. BC inflator hose
  11. Oral inflation mouthpiece and manual dump valve
  12. Crotch strap
  13. Waist strap

All BCs will have some features in common:

In addition some BCs may include other features:

Diver wearing an adjustable buoyancy life jacket

Types

There are three main types of BC based on buoyancy distribution:

Adjustable buoyancy life jacket

Surfaced divers with inflated horsecollar BCs

An adjustable buoyancy life jacket (ABLJ) is fitted around the neck and over the chest, secured by straps around the waist and usually between the legs. They are sometimes referred to as "horse collars" because of their resemblance, and are historically derived from the inflatable UDT vest or Mae West life jacket issued to World War II flyers and divers.

They were developed in the 1960s and have been largely superseded by wing and vest type BCs, primarily because of their tendency to shift the diver's center of buoyancy towards the head with inflation, which adversely affects the diver's trim underwater.[3] The ABLJ's location on the diver's chest and round the neck provides the best buoyancy distribution of the buoyancy compensater designs when it comes to floating a distressed, fatigued or unconscious diver face-up on the surface in the event of a problem.

The Dacor Seachute BC4 had unique upper and lower bladders. The upper bladder was around the neck and could be inflated by the CO2 cartridge for use as a surface life jacket. The lower bladder was over the diver's stomach area, and was inflated by LP gas from the regulator, for buoyancy control underwater. This arrangement provided better buoyancy distribution for trim control while diving than most other front inflation systems.[4]

Wraparound buoyancy BCs

Diver wearing a stabiliser jacket

Vest BC, stab jacket, stabiliser jacket, stab, waistcoat or disparagingly "Poodle Vest" BCs are inflatable vests worn by the diver around the upper torso, which incorporate the cylinder harness. The air bladder may extend from the back around the diver's sides ("wraparound") or may only cover the back ("back inflation.")

Wraparound bladders are favored by some divers because they make it easier to maintain upright attitude on the surface. However, some designs have a tendency to squeeze the diver's torso when inflated, and they are often bulky at the sides or front when fully inflated. Back inflation BC's are less bulky at the sides but may have a tendency to float the diver tilted forward on the surface depending on weight and buoyancy distribution, which presents a possible hazard in an emergency if the diver is unconscious or otherwise unable to keep his or her head above the water.

Vest BC's, whether back-inflated or wraparound, typically provide up to 25 kilograms of buoyancy (depending on size) and are fairly comfortable to wear, if of the correct size and adjusted to fit the diver. Vest BC's are the most common type among recreational divers because they can integrate buoyancy control, weights, attachment points for auxiliary gear, and cylinder retention in a single piece of gear. The diver need only attach a cylinder and regulator set in order to have a complete scuba set. Some "tech-rec" (technical and recreational) vest BC's have the ability to carry multiple cylinders - Twin sets on the back, and sling cylinders at the sides, suspended from D-rings. The lack of flexibility of positioning the D-rings due to structural constraints on some designs is partly compensated by fitting larger numbers of D-rings, some of which may be in the right place for a given diver.

Three main wraparound configurations can be distinguished:

BC attachment systems are generally intended to limit the shifting of the BC as a result of the lifting forces, including minimizing the tendency to slide towards the head when the diver is upright while the bladder is inflated. If the diver is wearing a weight belt, this will pull in the opposite direction to BC lift when the diver is upright, and can result in the diver sagging down in the jacket when floating at the surface. Solutions to this problem include the cummerbund (a broad adjustable waist band) and the crotch strap (a strap between the legs). The crotch strap, when adjusted correctly, is effective at preventing this shift, but may prevent the weight belt from falling clear of the diver if dropped in an emergency. Fitting the weight belt over the crotch strap after putting the BC on can be difficult. The cummerbund is an attempt to avoid this problem, as the weight belt can not be snagged on it in the same way, but the weight belt must then be worn either under the cummerbund, obstructing access to the buckle, or below the cummerbund. The effectiveness of a cummerbund depends on a waistline which is smaller than the circumference of the upper torso, and it may constrain free breathing if fitted too tightly.

This tendency of the inflated BC to shift towards the head is less of a problem when the weights are carried in integrated weight pockets on the BC, but it may then have a tendency to slide towards the head when deflated on an inverted diver underwater. This is less of a problem for the average recreational diver, who does not spend much time head down underwater.

Back inflation

Back inflation buoyancy compensators are typified by the stainless steel backplate and wing arrangement popular with technical divers, but other arrangements are also available. Wings or Backplate and wing consist of an inflatable bladder worn between the diver's back and the cylinder(s). Invented by Greg Flanagan in 1979 for North Florida cave divers, the back plate and wing configuration is not a recent development, but has regained popularity because of suitability for technical diving where it is often used, as the technical diver often carries multiple cylinders on his back and/or clipped to D-rings on the harness webbing. The bladder and cylinders or rebreather are fastened to a backplate which is strapped to the diver by the harness. The wing design frees the divers sides and front and allows for a large volume bladder with high lift capacity (60 lbs /30 liter wings are not uncommon). Some designs use elasticated webbing or bungee cords around the bladder to constrict the bladder when not inflated, although there is dispute as to the wisdom of this addition.[6]

Other back inflation buoyancy compensators are more like the jacket style regarding the structure, attachment to the diver, and accessories, differing mainly in the bladder position, which is similar to a wing, being entirely behind the diver, without extensions to the sides or front.

A few short-lived rigid air compartment back inflation BCs were marketed in the 1970s.

A hybrid arrangement is also possible, which has most of the buoyancy in the back, but has a small amount to the sides below the arms.

Sidemount wings

A variation on the back mounted buoyancy compensator is used without a backplate for side mount diving This arrangement is functionally similar to wearing the buoyancy compensator sandwiched between the cylinder(s) and backplate, but there is no backplate or back mounted cylinder. The buoyancy cell may be mounted between the sidemount harness and the diver, or on top of the harness.[7]

Some side mount harnesses are adaptable for use with a back mount cylinder as an option, without the rigid backplate.[7]

Construction

Buoyancy compensators of all types have been made in both single skin and casing and bladder arrangements. The strength and damage resistance of both these systems of construction depend more on the design details and quality of materials and manufacture than on the choice of arrangement, though maintenance may vary, as it is quicker to clean, dry and inspect a single skin than a bladder and casing, and the bladder and casing will have more components for an equivalent layout.

A single skin construction uses the material of the buoyancy bladder as the structural material for the unit, and a casing and bladder structure uses the casing for load bearing purposes and to protect the bladder, which is a replaceable part.

Operation

Neutral buoyancy

The diver needs to be able to establish three states of buoyancy at different stages of a dive:

  1. negative buoyancy: when the diver wants to descend or stay on the seabed.
  2. neutral buoyancy: when the diver wants to remain at constant depth, with minimal effort.
  3. positive buoyancy: when the diver wants to rise or float on the surface.

To achieve negative buoyancy, divers who carry or wear buoyant equipment must be weighted to counteract the buoyancy of both the diver and the equipment.

When underwater, a diver often needs to be neutrally buoyant so that the diver neither sinks nor rises. A state of neutral buoyancy exists when the weight of water that the diver displaces equals the total weight of the diver. The diver uses a BC to maintain this state of neutral buoyancy by adjusting the BC's volume and therefore its buoyancy, in response to various effects, which alter the diver’s overall volume or weight, primarily:

In practice, the diver doesn't think about all this theory during the dive. To remain neutrally buoyant, gas is added to the BC when the diver is negative (too heavy), or vented from the BC when the diver is too buoyant (too light). A feature of diving is that there isn't any automatically stable equilibrium position for a diver wearing a BC, or even simply for a diver with lungs full of air. Any change in depth from a position of neutrality and even a small changes in volume, including the simple act of breathing, result in a force toward an even less neutral depth. Thus, maintenance of neutral buoyancy in scuba must be a continuous and active procedure—the diving equivalent of balance, in a positive feedback environment. Fortunately, the diver's mass provides a source of inertia, as does the liquid medium, so small perturbations (such as from breathing) can be compensated for easily by an experienced diver.

A feature of scuba which is often non-intuitive for beginners, is that gas generally needs to be added to the BC when a diver descends in a controlled manner, and valved-off (removed or vented) from the BC when the diver ascends in a controlled manner. This gas (added or vented) maintains the volume of the gas bubble in the BC during depth changes; this bubble needs to remain at constant volume for the diver to remain even approximately neutrally buoyant. When gas is not added to the BC during a descent, the gas bubble in the BC decreases in volume due to the increasing pressure, resulting in faster and faster descent with depth, until the diver hits the bottom. The same runaway phenomenon, an example of positive feedback, can happen during ascent, resulting in uncontrolled ascent, until a diver prematurely surfaces without a safety (decompression) stop.

With experience, divers learn to minimize this problem, starting by minimizing the size of the "constant volume bubble" in their BC's. This requires learning the minimum weighting requirement needed for their system (see factors above). These techniques keep the volume of the gas bubble within the BC as small as possible at the beginning of a dive, while leaving just enough gas in the BC at first submersion to be able to compensate for the expected slow loss of diver weight as the dive progresses, as a result of gas used (in practice, about 5 to 8 lbs. lost per cylinder, as noted above).

Somewhat complex automatic reflex behaviors are also developed by experienced divers, involving breathing control and BC gas management during depth changes, which allow them to remain neutrally buoyant from minute to minute during a dive, without having to think much about it. Experienced scuba divers may often be identified by the fact that they maintain neutrality without any fin use, as fish do.

Orientation in the water

Main article: Diver trim
Divers with neutral buoyancy and horizontal trim are less likely to touch / disturb the bottom

The vertical-horizontal orientation, or trim, of the submerged diver is influenced by the BC and by other buoyancy and weight components and contributed to by the diver's body, clothing and equipment. The diver typically wishes to be positioned nearly horizontally (prone) while under water, to be able to see and swim usefully, but more nearly vertical and perhaps partly supine, to be able to breathe without a regulator when on the surface. Buoyancy and trim can significantly affect hydrodynamic drag on a diver and the effort required to swim. The effect of swimming with a head up angle, of about 15° as is quite common in poorly trimmed divers, can be an increase in drag in the order of 50%.[10]

The orientation of a static and stable object in water, such as a diver, is determined by its center of buoyancy and its center of mass. At equilibrium, they will be lined up under gravity with the center of buoyancy vertically on a line with, (and preferably above) the center of mass. The diver's overall buoyancy and center of buoyancy can routinely be adjusted by altering the volume of the gas in the BC, lungs and diving suit. The diver's mass on a typical dive does not generally change by what seems like much (see above—a typical dive-resort "aluminum 80" tank at 200 bar contains about 2.8 kg (~6 lbs) of air or nitrox, of which about 2.3 kg (~5 lbs) is typically used in a dive, although any air spaces such as in the BC and in diving suits will expand and shrink with depth pressure. Large changes in buoyancy are of course possible if the weight belt is jettisoned, or a heavy object is picked up.

Generally, the diver has little control of the position of the center of buoyancy in the BC during a dive, only the amount of buoyancy. However the diver can change his/her centre of gravity by adjustment of the equipment setup, which includes its configuration and position of weights, which ultimately influence where the effective BC lift is positioned relative to his Center of Gravity.[11]

Traditionally, weight belts or weight systems are worn with the weights on, or close to, the waist and are arranged with a quick release mechanism to allow them to be quickly jettisoned to provide extra buoyancy in an emergency. Weight carried on a belt can be distributed to shift the weight forward or backward to change the position of the diver's center of mass. Systems that integrate the weights into the BCD, can provide added comfort so long as the BCD does not have to be removed from the body of the diver, for example in an underwater emergency such as an entanglement. When a weight integrated BCD is removed a diver wearing no weight-belt and any type of foamed neoprene wetsuit will be very buoyant.

By inflating the BC at the surface, the conscious diver may be able to easily float face-up, depending on his equipment configuration choices. A fatigued or unconscious diver can be made to float face up on the surface by adjustment of their buoyancy and weights so the buoyancy raises the top and front of the diver's body and the weights act on the lower and back of the body. An inflated Horse-collar always provides this orientation, but an inflated vest or wing may float the diver face-down if the center of buoyancy is behind the centre of gravity. This floating orientation is generally considered undesirable and can be minimized by relocation of some of the weights further to the rear, and using higher density cylinders (typically steel), which also move the center of mass towards the back of the diver. The BC type can also be selected with this factor in mind, selecting a style with a center of buoyancy further forward when filled, as this has the same net effect. Any or all of these options can be utilized to trim the system out to its desired characteristics[12] and many factors can contribute, such as the number and position of diving cylinders, the type of diving suit, the position and size of stage cylinders, the size and shape of the diver's body and the wearing of ankle weights, or additional dive equipment. Each of these influence a diver's preferred orientation under the water (horizontal) and at the surface (vertical) to some degree.

Hazards

Gas supply and consumption

Gas consumption varies depending on the dive profile and diver skill. The minimum consumption is by a diver who uses the correct amount to neutralize buoyancy and does not waste gas by overfilling, or by excessive weighting. The actual volume of the bladder should not affect gas consumption by a skilled user. Deep dives will require more gas, and dives in which the diver ascends and descends by large amounts and/or frequently, will require venting for each ascent and top up for each descent. The amount of gas used was generally below 6% of the gas consumption during the dive during US Navy trials[4] and the use of small pony cylinders for inflation was considered adequate, but not necessary.

Most BCs allow oral inflation both underwater and on the surface. This could theoretically reduce gas consumption, but is generally not considered worth the effort and slightly increased hazard of taking the DV out of the mouth underwater, and possibly having to purge it before breathing again. Oral inflation is, however, an alternative inflation method in case of a failure of the pressurized inflation system.

Emergency inflation by expendable CO2 cartridge is provided on some BCs.

History

In 1957, F. G. Jensen and Willard F. Searle, Jr began testing methods for manual and automatic buoyancy compensation for the United States Navy Experimental Diving Unit (NEDU).[14] In their early tests, they determined that manual systems were more desirable due to the size of the automatic systems.[14] Later that year, the Walter Kiddie and Co. sent a prototype buoyancy compensating tank for use with two cylinders to NEDU for evaluation.[15] The valves of this aluminium tank system leaked and testing was delayed until 1959 when it was recommended for field testing.[15]

The ABLJ was developed by Maurice Fenzy in 1961.[3] Early versions were inflated by mouth underwater. Later versions had their own air inflation cylinder. Some had carbon dioxide inflation cartridges (a holdover, for surface use, of the Mae West flyer's lifejacket) to facilitate emergency ascent. This was abandoned when valves that allowed divers to breathe from the BC's inflation bag were introduced. The Fenzy ALBJ provided a proof of concept for buoyancy compensation, however the large-volume ring behind the diver's neck caused the jacket to ride up against the diver's windpipe, despite the crotch strap.

In 1968, dive shop owners, Joe Schuch and Jack Schammel, developed a more comfortable buoyancy compensator vest that featured a smaller buoyancy ring behind the diver's head, and a midriff section with sufficient volume to lift the diver's head out of the water in the event that one or both of its CO2 cartridges were detonated for emergency ascent. In 1969, the original Control Buoyancy Jacket or "CBJ" was manufactured by Waverly Air Products of Chemung, NY and sold in dive shops throughout the east coast of the United States. By 1970, a push-button inflator using air from the diver's SCUBA tank augmented the manual inflation hose.

Since 1970 most BCs have used for inflation mainly gas from one of the diver's main cylinders, and an oral inflation tube have been generally retained for abnormal situations (no high pressure gas left, malfunction of an inflator hose) both underwater and on the surface.

Scubapro introduced the stabilizer jacket in 1971, with a patented "360° flow through design", which allowed air to flow over the shoulders and under the arms, and around the cylinder mount. Later products from competitors avoided patent infringement by eliminating some of the air path options, such as separating the bladder under the arms or over the shoulders.[5] These modifications also simplified the structure of the bladder. One of these later models was the Seatec Manta, with shoulder buckles and a softpac structure (without a rigid backpack)[5]

In 1972, Watergill developed the At Pac wing, the first wing-style BC, which was provided with a cummerbund and padded shoulder straps, and an integrated weight system.[5]

In 1985 Seaquest, Inc. introduced the Advanced Design Vest (ADV), a design featuring an under-arm wrap, shoulder buckles and a cummerbund. This design was duplicated by other manufacturers and continues to be produced as of 2013 [5]

Rigid shell back inflation buoyancy compensators were marketed by U.S Divers (UDS-I system) and Dacor (CV Nautilus)for a short period in the mid 70s. The Nautilus had an automatic inflation system using a regulator to maintain a constant volume, but the changes in buoyancy due to wetsuit compression and gas usage were not well compensated and the system never caught on.[5]

More recent innovations for jacket BCs include weight pouches to adjust attitude underwater, putting the weights on the BC rather than on a weightbelt, integrated regulators, heavily reinforced 1050 denier ballistic nylon. Innovations for backplate and wing include redundant bladders, stainless steel backplates, lightweight soft nylon backplates, and 85 lb lift bladders.

Dive Rite pioneered the first purpose-built wing for diving twin cylinders in 1985. Other tech diving wing manufacturers include Ocean Management Systems, Halcyon and Oxycheq. Other BC manufacturers include Sherwood, Zeagle, Scubapro, Mares and Cressisub.

Other buoyancy equipment

There are other types of equipment worn by divers that affect buoyancy:

See also

Wikimedia Commons has media related to Buoyancy compensators.

References

  1. 1 2 European terminology
  2. 1 2 North American terminology
  3. 1 2 Historicizing Lifestyle: Mediating Taste, Consumption and Identity from the 1900s to 1970s (Hardcover), Raptures of the Deep: Leisure, Lifestyle and Lure of Sixties Diving by Bill Osgeby ISBN 978-0-7546-4441-5
  4. 1 2 3 4 5 Middleton, JR. (1980) Evaluation of Commercially Available Buoyancy Compensators. US Department of Defense Technical Information Center (http://www.dtic.mil/) http://archive.rubicon-foundation.org/3374 Accessed 5 June 2013
  5. 1 2 3 4 5 6 McLean, David. (2006) https://drive.google.com/?tab=wo&authuser=0#folders/0B3Z4b8qrjCTWSkJWd1N6YW5udTQ accessed 2 December 2013
  6. Discussion of Bungied Wings, aka Bondage Wings
  7. 1 2 Kakuk, Brian; Heinerth, Jill (2010). Side Mount Profiles. High Springs, FL: Heinerth Productions. ISBN 978-0-9798789-5-4.
  8. 1 2 Williams, Guy; Acott, Chris J (2003). "Exposure suits: a review of thermal protection for the recreational diver". South Pacific Underwater Medicine Society journal 33 (1). ISSN 0813-1988. OCLC 16986801. Retrieved 2009-06-13.
  9. Fead, L (1979). "Is dropping your weight belt the right response?". South Pacific Underwater Medicine Society Journal (reprinted from: NAUI News, September 1978) 9 (1). ISSN 0813-1988. OCLC 16986801. Retrieved 2009-06-13.
  10. Passmore M.A, Rickers, G. (2002), Drag levels and energy requirements on a SCUBA diver Sports Engineering 2002, 5, 173-182, Blackwell Science ltd.
  11. Swimming Position Centroid Calculation Methodology illustration from huntzinger.com
  12. Surface Buoyancy Moment Arm illustration from huntzinger.com
  13. http://www.emedmag.com/html/pre/tox/0500.asp CO2 Toxicity
  14. 1 2 Jensen, FG; Searle, Willard F (1957). "Buoyancy Control of Open Circuit Scuba". United States Navy Experimental Diving Unit Technical Report. NEDU-RR-8-57. Retrieved 2009-06-13.
  15. 1 2 Janney, G. M; Hanger, G. W (1960). "Walter Kiddie and Co. - Buoyancy Compensating Tank". United States Navy Experimental Diving Unit Technical Report. NEDU-Evaluation-7-60. Retrieved 2009-06-13.

Further reading

This article is issued from Wikipedia - version of the Tuesday, April 19, 2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.