Akaflieg München Mü10 Milan

Mü10 Milan
Role Training Glider
National origin Germany
Manufacturer Akaflieg München
Designer Dipl.-Ing. Egon Scheibe
First flight 1934
Retired 1959
Number built 1


|} The Akaflieg München Mü10 Milan is a two-seat glider aircraft that was designed in Germany in 1934.[1] Only one copy of the design was built.

Development

The Mü10 Milan is one of the most successful gliders built by Akaflieg München in its early history. Construction of this two-seater, designed by Dipl.-Ing. Egon Scheibe, uses mixed materials with wooden wings and tail surfaces covered with fabric, as well as a welded steel tube fuselage covered with fabric, the first time welded steel tubing was used for a practical sailplane.

Performance of the Mü10 Milan was found to be good at low speeds, suiting the aircraft to thermalling, due to the use of homegrown aerofoil sections developed by Egon Scheibe, who was now leader of the Akaflieg München design team. The sections used were highly cambered in the leading edge with virtually no camber aft of mid chord, producing a section with reduced twisting and pitching moments and high lift coefficients.

Accommodation in the Mü10 Milan was in two cockpits, one forward of the wing leading edge for the student and another under the trailing edge of the centre-section aft of the mainspar. Entry into the front cockpit was via a removable canopy, (largely opaque with portholes in the first iteration), built up with wooden frames and Plexiglas panels. The rear cockpit was accessed via a large door on the port side of the fuselage with windows under the wings forward to the front cockpit glazing and in the centre-section above the instructor's head. The rear access door could also be used as an airbrake to assist in approach control.

A close-up of the nose showing the Akaflieg München logo.

Despite the low performance of the Mü10 Milan, with an L/D of 20, the aircraft was listed as high performance as late as 1938, perhaps due to the many cross-country flights the aircraft is credited with, such as Hesselberg-Prague (1934), a world record breaking 180 km flight in 1935, Salzburg-Fara d'Alpago / Italy (195 km, 1937) and Bern-Pallanza/Lago Maggiore (136 km; 1938) as a two-seater. Success in gliding competitions was also achieved with the 1934 Rhön-construction prize and 1st place at the ISTUS Conference (International Study Commission for gliding). At Salzburg it was flown by Ludwig Karch to a height gain of 2980m (9777 feet) and 195 km (121 miles) distance over the Austrian Alps.[2]

The 'Milan' was retired to the Deutsches Museum München, at Oberschleissheim, before World War II, surviving the war to be resurrected by Akaflieg München in 1951 to assist with training new students, as well as carry out long distance cross-country flights and mountain flying, until at least 1959 with the Mü10 finally being retired to the Deutsches Museum München for a second time.

The Mü15 showing the retractable mainwheel

Variants

Akaflieg München Mü10 Milan – two-place glider; steel-tube fuselage, Mü Scheibe wing section and wooden wings. One unit constructed.
Akaflieg München Mü15 - Development of the Mü 10 with 19m span wings, flaps and a mainwheel.[3]
A development of the Mü10 with a longer wing, flaps and a mainwheel was first flown in 1940, at Ainring in Austria, as the Akaflieg München Mü15. This aircraft was equipped for blind flying but had poor roll response, requiring large doses of the oversized rudder to complete turns with lots of skid. Flown until the war situation became too serious, the Mü15 had flown a total of 45 hours when flying ceased in November 1941.[3]
Akaflieg München Mü20 - Further development of the Mü10/Mü15 line with a 20m (65.6 feet) wing and 500kg all-up weight. Design of the Mü20 was almost complete when work was abandoned.[4]
Further improvement in the two-seat Mü10/Mü15 line came with design of the 20m span Akaflieg München Mü20, design of which was almost complete when it was abandoned.[4]
Akaflieg München Mü24 Milan II - A proposed instrument flying-version[5]
In the early 1960s students at the Akaflieg designed a cloud/instrument flying version of the Mü10. The Akaflieg München Mü24 Milan II was to have had similar layout and profiles to the Mü10, with the slow-flying qualities of the Mü Scheibe aerofoil sections and improved aerodynamics for the fuselage and wings. The Mü24 did not progress beyond the drawing board.[5]

Specifications (Mü10 Milan)

Data from [2]

General characteristics

  • Crew: 1 pilot
  • Capacity: 1 passenger
  • Length: 6.725 m (22 ft 1 in)
  • Wingspan: 17.8 m (58 ft 5 in)
  • Wing area: 20 m2 (215 ft2)
  • Aspect ratio: 15.8
  • Wing profile: Scheibe Mü
  • Empty weight: 180 kg (397 lb)
  • Gross weight: 335 kg (739 lb)

Performance

  • Maximum glide ratio: 20
  • Rate of sink: 0.65 @ 50 km/h (31 mph) m/s (128 ft/min)

References

  1. Mü10 "Milan"
  2. 1 2 Simons, Martin. Sailplanes 1920-1945”. 2nd revised edition. EQIP Werbung und Verlag G.m.b.H.. Königswinter. 2006. ISBN 3-9806773-4-6
  3. 1 2 Mü15
  4. 1 2 Mü20
  5. 1 2 Mü24 "Milan II"
  • Simons, Martin. Sailplanes 1920-1945”. 2nd revised edition. EQIP Werbung und Verlag G.m.b.H.. Königswinter. 2006. ISBN 3-9806773-4-6
This article is issued from Wikipedia - version of the Tuesday, June 23, 2015. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.